Search Documents

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By C. O. Esterhuysen, J. P. Deetlefs, C. A. Wessels

The productivity indices of the Republic of South Africa compare poorly with those of its competitors in the rest of the world. The theory of productivity is relatively simple, and various models are available to demonstrate this. The problem is how to apply the theory in practice and to convert it into a practical management system that will guarantee results. The secret lies in a management approach that aims at a continuous improvement in achievement and that involves the entire work force down to the lowest level in the process. Good management systems ensuring the necessary attention to, among others, management by objectives, finance, personnel, maintenance, planning, and control are a prerequisite for continued improvement and staff involvement. The net result of such an approach is described by the term performance management, which encompasses the total integration of al a company's management systems.

Jan 1, 1989

By Ira Brotman

The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S. his paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20?30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition. The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project?s progress and allow for validation of consolidation and strength gain rates and magnitudes.

By R G Warren

Sparse geochronological data have been combined with data on felsic suites and depositional facies of rocks to provide an overview of the development of the Arunta Block. The study provides a basis for construction of a map showing the distribution of granites and associated felsic extrusive rocks in the Anmta Block. The tectonic evolution can be subdivided into a series of significant time intervals. Only in the initial stage, to about 1880 Ma, was there any subduction-related magmatism. All later felsic magmas were crustal-derived melts. The early, pre-1880 Ma arc-related units in the SE contain small showings of Cu, probably including the small Cu deposit in the Casey Bore Inlier at the edge of the Simpson Desert. The most significant time-interval for formation of mineral deposits was 1820-1760 Ma, when volcanogenic Cu-Pb-Zn deposits formed in the Strangways Metamorphic Complex and also in the Jervois district. Stratabound tungsten lodes in the hanging wall of

Jan 1, 1994

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By Paul D. Foote

Most of the treatises on metallurgy intimate that simultaneously with the development by the atomic physicist of a really satisfactory theory of the atom will be inaugurated a new epoch in the science of metals. Metallurgically and metaphorically, we shall dwell in the Utopia of Sir Thomas More. It is my privilege this afternoon to demonstrate that this state has not arrived. An atom is a miniature planetary system consisting of a positively charged nuclear sun about which revolve electrons each carrying the negative charge e. The charge on the nucleus is + Ze where Z is the atomic number and the number of planetary electrons in a neutral atom is equal to Z. These electrons are arranged in several groups having different binding energies. Ordinary x-ray phenomena relate to processes occurring deep within the atom, usually with electrons in the so-called K or L shells. Such electrons in the heavier atoms are so closely bound to the nucleus that the forces exerted by neighboring atoms in a solid are relatively inappreciable. For most practical x-ray investigation, the atom may be considered as in the gaseous phase completely isolated from its neighbors. The K radiation from an element in the gaseous state, in the solid or liquid phase, or even in combination with other elements in all its possible valences, is almost identical.‡ Visual and ultraviolet spectroscopy is concerned with disturbances of the most loosely bound outer or valence electrons of the atom, always in the vapor state. The remarkable progress of the last year in both theo-

Jan 1, 1926

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By J. A. Dos Santos

"INTRODUCTION Dramatic reduction in energy use and environmental impact can be achieved with sandwich belt high angle conveyors that serve as the vital link in any IPCC (In-pit Crushing and Conveying) system. These high angle conveyors are not new at all, but have not found wide use in IPCC systems where they can realize the greatest advantage. Reduced energy consumption and environmental impact, with IPCC systems, was already realized in the 1970s. With the bulk material haulage limited to conventional open trough conveyors the most direct path out of the open pit was precluded, requiring low angle spiral ramps and/or deep slots and/or tunnels through the high wall of the open pit. These excavations, to accommodate the low angle limitations, represented undesirable impact on cost and on the environment. Against this backdrop, a major study in 1979 sought to develop high angle conveying systems that could continuously haul the mined bulk material directly out of the pit, along the high wall – the shortest distance between the two end points. Between 1979 and 1982, that study developed sandwich belt high angle conveying systems that utilized all conventional conveyor equipment including smooth surfaced rubber belts that could be continuously scraped clean. These systems had all of the positive features of conventional conveyors but overcame the angle limitation. By hugging the bulk material between two belts, the material’s internal friction could be developed to facilitate conveying at any high angle up to 90 degrees (vertical). After an intense testing period (about one year) on the first large scale prototype system, commercialization began in 1983 with the installation of a 60 degree incline system at a western United States coal mine, elevating 2000 t/h of coal to a train load out system. It did not take a long period of scrutiny and acceptance before this high angle conveyor found use in the most rugged requirements of an IPCC system. This was only the second commercial sale, and after more than 150 commercial installations, it remains arguably the most significant high angle conveying system. In 1984, a copper mine in Serbia, already using pit perimeter crushing and conveying, decided to move their primary crusher deep into the pit and to use a sandwich belt high angle conveying system to elevate the ore continuously, directly out of the pit, along the high wall to the pit perimeter where it then transferred to a conventional conveyor for the remaining haul to the plant. The system had significant features including 2000mm wide belts that elevated 250mm coarse ore, at 4000 t/h, over six 15-meter high benches for a total 90 meters of net lift. The system was able to reduce the truck haulage fleet by ten 200 ton trucks realizing great cost savings, zero emissions to the air and greatly reduced traffic congestion in the pit. The system operated successfully until 2002 when the mine shut down. Many successful sandwich belt high angle conveyors followed with the current count of commercial installations at more than 150. Despite the great success with this system, its use has not been repeated as part of an IPCC system."

Jan 1, 2018

By H. Wilton Clark

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and wash-ability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semi-anthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations. The pitching seams, chiefly Lower Cretaceous, occur in the western belt of the Rocky Mountain foothills and the eastern slopes of the Rockies themselves. (The road to Tent Mt. strip pit, elevation 7000 ft, is shown on p. 832.) Formations extend from the U. S.-Canadian boundary for several bundred miles in Alberta and continue for a similar distance in British Columbia. Present geological estimates show a probable reserve of the order of 25,000 million tons of coal ranging from high volatile bituminous to semi-anthracite, with a large percentage of coking coal, constituting one of the major world reserves of that type. It should be noted that although the quoted estimate probably errs on the conservative side, the question of access to the seams in a mountainous terrain will always be a problem; a wide divergence may exist between actual reserves and the quantities of coal economically recoverable. An excerpt from the Canadian government Report of the Royal Commission on Coal 1946 states that conditions favorable to coal formation were intermittent and these intervals relatively brief in comparison with periods in which no coal was formed. Conditions were favorable to the growth or accumulation of vegetation in one area, while fresh water sediments and marine shales were being deposited in other areas. During periods of emergence the coal deposits were subjected to erosion or were covered by coarse sands and gravels from the mountains, whereas during submergence they were covered by fine clays deposited in embayments of the sea. During some of the periods of coal formation, volcanic activity deposited beds of fine volcanic ash and dust with the coal-forming vegetation. Coal deposits reach their greatest development in the mountains and thin rapidly to the east into the plains area, where they are deeply buried beneath younger sediments. For example, in the Fernie area of southeastern British Columbia there are in places 22 seams having an aggregate thickness of 150 ft in a stratigraphic interval of 3500 ft, whereas at Cole-man in the Alberta Crowsnest area the measures are only 800 ft in thickness and contain a maximum of five seams aggregating about 47 ft of coal. At Belle-vue, 10 miles further east, the measures are reduced to 430 ft with only three seams aggregating about 37 ft of coal. Subsequently the tremendous forces involved in the upthrust of the Rocky Mountains produced great displacement of the coal-bearing formations and at the same time a change in geologically young coals from low to high rank. The floor or footwall of most seams consists of carbonaceous shales, which are almost as adaptable to bending as the coal seams themselves. The seams show very few cleats or cleavage planes and have been so weakened structurally that as mined 50 pct or more will pass through a ¼-in. screen, seldom

Jan 1, 1955

By John Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6, without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high MgO siliceous phosphate matrix from South Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth, and the phosphate flotation stage produced concentrates analyzing about 31% P20S' 0.7% MgO and 4% acid insolubles. The overall P20S recovery in the two stages is about 85%.

Jan 1, 1989

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By Unkown

To the Membership of the Institute Gentlemen: The Mineral Industry of Canada in 1948 The preliminary estimate issued by the Dominion Bureau of Statistics and tabulated in the Bulletin of January, 1949, indicated that the value of Canada's mineral production in 1948 reached an all-time high of $808,180,216, showing an increase of 25 per cent over the previous record of $644,696,007 established in the preceding year. The output value of metallics was increased by 22.4 per cent; of fuels, by 43.7 percent of other non-metallics, by 19 per 'cent; and of structural materials, by 16.8 per cent. The value of metals produced in 1948 at $483,770,759, was about $87,000,000 more than in the previous year. There were substantial increases in the tonnages of copper, lead zinc nickel, and other base metals produced, but the rises in market prices for such metals accounted for most of the gains in output values. Production of gold at 3,495,403 ounces valued at $122,339,105 indicated an increase in volume of approximately 500,000 ounces and an increase in value of 14 per cent. Despite the benefits provided under the Emergency Gold Mining Assistance Act 1948 the volume of gold produced in the year was still nearly 2,000,000 ounces less than the record of 5,300,000 ounces established in 1941. The value of mineral fuels produced in 1948, at $158,787,255, was 44 per cent above the 1947 total. Coal production at 18,431,250 tons valued at $107,298,757, while substantially higher than in the preceding year was still half a million tons below the record reached in 1942. Striking developments in the Leduc field in Alberta were responsible for bringing the output of crude petroleum in the year to a new high of 12,098,166 barrels, valued at $36,858,959.

Jan 1, 1949

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012