Search Documents

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By N. A. D. Parlee, I. D. Shah

ThIS reports on some work done on the solubility and diffusivity of oxygen in liquid silver. Solubility. Improvements in the measurement of the solubility of oxygen in silver and silver alloys were made because precise data were needed for calculating diffusion coefficients of oxygen in these alloys. The apparatus and the procedure used were similar to those of Parlee and Sacris.' The main improvement was in the temperature-measuring technique. A MV30 mullite protection tube containing a calibrated Pt-Pt, 10 pct Rh thermocouple was inserted in the reaction tube from the top through a vacuum-tight swage-lok fitting. The protection tube was well-immersed in the liquid silver, which was heated by induction. A Leeds and Northrup potentiometer was used in connection with the thermocouple. All runs reported were made at 1 atm. The temperature range investigated varied from 940" to 1200°C. The ternary point in Ag-0 phase diagram2 is at 939°C and 0.32 wt pct O. This point was reinvestigated using the above-described apparatus and was found to be at 939°C and 0.315 wt pct 0. It was determined by observing the sudden evolution of oxygen at this point while the solubility measurements were made. The point was easily reproducible if precautions were taken to keep the liquid silver essentially in equilibrium with oxygen and to lower the temperature very slowly. All of the results of this new solubility investigation are plotted in Fig. 1. They are represented by the "least-squares" line shown in the figure and the following equation for solubility at po2 = 1 atm: log% O =695.4/T - 1.086 This equation differs only slightly from that proposed by Parlee and sacrisl and that of Diaz, Masson, and Richardson.3 The points of Parlee and Sacris, using an optical pyrometer, are shown for comparison.

Jan 1, 1968

By Julius Rubinstein, Victor Badenicov

The development of column flotation is the most significant achievement in the area of mineral processing in the last few decades. The high efficiency of column flotation allows a reduction in process time, a decrease in the number of cleaner stages and in the volume of the circulating load in the flotation circuit, and, as a result of this, an increase in consistency and reliability of operations. Unique multisectional column flotation apparatuses were developed. Such designs have a number of essential advantages as compared to monocells. A change from monocells to multisectional column allows to provide favourable conditions for separation of particles of various floatability. To attain that aim particular hydrodynamics and aeration regime is established in each section of the column, operational variables being adjusted according to the floatability of the material. Therefore in multisectional column machines the material-apparatus feedback can be established, process variables optimized depending on the characteristics of the floated materials. This concept forms the basis of column designs we have developed. For the first time column cell with alternating slurry Rows (combination of co- and counter-current flows) were developed and commercialized . Successful operation was reported of the new generation of columns with cell volumes of 10 to 80 m3 and the height of 4-6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants. Operation experience of these cells showed their considerable design and operational advantages and verified the proposed options and relationships. The new apparatus is provided with a pneumohydraulic aerator allowing to control bubble size distribution, the service life of the aerator is not less than two years. A multilevel flotation model was developed and used to work out a technique of column design and process parameters calculation. A method of the apparatus design parameters calculation based on laboratory test results (scaling up) was worked out. The method is based on flotation macro and micro-hydrodynamics simulation.

Jan 1, 1995

By E. G. Beinlich

The continuing search for faster, safer, and more economical methods of excavating underground openings has led the staff of the Mather mine of the Negaunee Mine Co. directly to mechanical boring of raises and drifts. The mine is located within the city limits of Negaunee and Ishperning in the eastern portion of the Marquette Iron Range in the Upper Peninsula of Michigan. It is owned jointly by McLouth Steel Corp., Bethlehem Steel Corp., Republic Steel Corp., and The Cleveland-Cliffs Iron Co., who also serves as the operating agent. A total of 2,400,000 tons of iron ore averaging over 60% Fe is mined annually by the block-caving method. This provides feed for the Pioneer pellet plant at Eagle Mills where 1,450,000 tons of pellets are produced yearly with the remaining tonnage being sold as coarse ore. Technical staff of Cleveland-Cliffs have long realized that improved methods of advancing raises and drifts were a necessity if underground mining of iron ore was to survive the transition period in the steel industry's requirements from direct-shipping ore to pelletized ores. For this reason, the Mather mine embarked upon an experimental raise-boring program with a prototype machine in 1961. Improvements since that time in equipment and practice have resulted in the acceptance of mechanical boring of raises as a standard development tool and a vital link in the fulfillment of an orderly development schedule. Advancement of large-diameter openings such as main-level drift headings by mechanical methods in the harder, more competent types of rock has developed more slowly in the mining industry due to the need for more compact and portable machinery and improved bit technology. Many of the obstacles have been overcome by the manufacturers, and in March 1967 it was decided to proceed with a program to bore approximately 4000 ft of 13-ft-diam drift in the Mather graywacke footwall rock.

Jan 1, 1970

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By W. K. Collins

Engineered Scavenger Compounds (ESCs), developed by the U.S. Bureau of Mines, are a novel class of compounds that can selectively recover a desired element from a solid or molten alloy. Lithium titanate (Li2Ti3O7 or L'20-3T'02) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (Al-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both are metastable, the hexagonal phase that forms during the scavenging of Li from Al-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li2Ti3O7 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1993

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

In low carbon TRIP steels, the formation of carbide-free bainitic ferrite is crucial for the stabilization of austenite. Based on experimental investigations modeling the bainite reaction is examined adopting diffusional and displacive mechanisms, as well as the semi-empirical JMAK approach. Transformation tests were carried out to study the isothermal austenite decomposition into bainitic ferrite for a model steel containing 0.6wt%C, 1.5wt%Mm and 1.5wt%Si which replicates the composition of remaining austenite at the start of the bainite reaction in a classical C-Mn-Si TRIP steel. In the diffusional approach, classical nucleation theory is employed and subsequent growth of bainite plates is modeled using the Zener-Hillert theory. In the displacive approach, the autocatalytic nucleation of bairtite plates is assumed to be rate controlling. The predictive capability of all models is evaluated for temperature ranges where different morphologies of bainitic ferrite have been detected, The shortcomings and inherent challenges associated with either of these modeling approaches will be delineated.

Jan 1, 2003

By J Lainé, M Badawi, A C. de Araujo, Y Foucaud, C Veloso

Flotation is the one of the most used techniques for the mineral separation of non-ferrous ores worldwide. However, the increase of the complexness along with the decrease of ores liberation sizes ought to become important challenges for mineral processing, including flotation. It now appears necessary to better understand the fundamentals of the flotation process, particularly the adsorption of flotation reagents at the liquid/mineral interfaces, to propose further improvements. Flotation relies on different phenomena: surfactants adsorption, on one hand, and collision, adhesion, and transport of particles with bubbles, on the other hand. For acknowledging the reagents adsorption mechanisms, molecular modelling tools borrowed from chemical and material sciences, are increasingly used. Atomistic simulations were successfully applied to study the flotation reagents interaction with various mineral surfaces, eg of two common minerals from iron ores, kaolinite, and magnetite surfaces, or with fluorite surface, a tungsten ores common gangue mineral.

Aug 24, 2022

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10 ? 15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2012

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By P. N. Harris

The Colloquium on 'Recent Mining and Metallurgical Developments in the Orange Free State' was held at the Civic Centre in Welkom on the 4th and 5th May, 1983. The Chairman of the Orange Free StatejKlerksdorp Branch of the Institute and Acting General Manager of Unisel Gold Mining Company, Mr D. A. Parfitt, opened the proceedings, and Professor A. N. Brown gave the welcoming address. Mechanization of mining The South African Institute of Mining and Metallurgy is to hold a one-day colloquium on 'Developments in the Mechanization of Mining Operations' during September 1984. Surfac,e mining and quarrying The Second International Surface Mining and Quarrying Symposium is being organized by The Institution of Mining and Metallurgy in association with the Institute of Quarrying.

Jan 1, 1983

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By Lewis Blanchard Brown

It is my purpose in the following paper to describe the south-central part of Siberia, with special reference to its geology and the mineral deposits. This region is known politically as the Achinsk and Marinsk districts of the Tomsk Government. It is situated among the Altai mountains, in. ]at. 50° to 55O n and long. 87O to 93O E., not far from the northern frontier of Mongolia, and is divided as follows: Mining Districts.—(1) The Tomsk mining district, including the political districts of Altai (belonging to the private crown lands of the Russian Emperor) and Marinsk; (2) the AchinskMinusinsk mining district, including the political districts of Achinsk and Minusinsk; and (3) the North Yenisei mining district, situated in the northern part of the Yenisei political district of the Yenisei Government. Fig. 1 is a map of the Tomsk mining provinces, showing the useful mineral-deposits, excepting those of gold, and giving the routes of the railroads and post-roads connecting the various districts. Political Divisions.—The Tomsk Government is sub-divided into seven " oojesdy " or districts, as follows: Barnaul; Biisk; Kuznetsk; Kainsk; Kolyvan; Marinsk; Narim; and the Altai district (private land, as above). The Yenisei Government is sub-divided into five "oojesdy" or districts, as follows : Erasnojarsk ; Kansk; Yenisei; Achinsk; Minusinsk. Concerning the geology of the region, in addition to the record of my own observations, references will be made to the works of earlier writers. These have been consulted for the purpose of comparison, as regards the districts which I have actually traversed, and for the purpose of completing my account of such portions as I have not been able to visit.

Jan 1, 1904

By Zárate G. E.

Practical and statistical considerations concerned with the sampling, sample preparation and chemical analysis of precious metal ores are reviewed. The principal requirements related with the characteristics of sample cutter, sample preparation, equipment and methods are discussed. The main errors introduced in the different stages of the sampling systems are defined. The application of statistical techniques to evaluate these errors to determine the ore grade variation and to design the number of increments needed to get an accurate assay are presented. Finally, results obtained with the application of this method to gold and silver ores are analyzed and some recommendations are given.

Jan 1, 1984