Search Documents

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By S. E. Bretherton

MOST metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other metals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthless. Such was the experience of the oldest mines in Leadville, Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered y smelting the cinder or clinker left in the re-

Jan 7, 1914

By Dorsey A. Lyon, Robert M. Keeney

This bulletin is one of a series dealing with the application of the electric furnace to the smelting of ores and the manufacture of alloys, and is published by the Bureau of Mines in the endeavor to increase efficiency in metallurgical processes. The bulletin presents, first, a critical discussion of the possibility of smelting copper ores in the electric furnace; second, the results of the experimental work of other investigators on the electric smelting of copper; third, the results of experiments by the authors on the electric smelting of native copper concentrates and sulphide copper ores; and, fourth, a comparison of the electric furnace with the blast furnace and reverberatory furnace for copper smelting. Before considering the electric smelting of copper ores the reader should understand that the electric furnace was not developed as a competitor of the combustion furnace, but for the purpose of doing high-temperature work that can not be done in the combustion furnace, and for the treatment of ores from deposits that are in regions where fuel is scarce and costly but hydroelectric power is comparatively cheap, as in Chile, and in certain parts of Canada, the United States, and Mexico. Furthermore, it is not the object of this report to try to prove that the electric furnace should replace the reverberatory or the blast furnace, as used at present in smelting copper ores, but to show that the electric furnace may be used with advantage in localities where conditions are not favorable to the use of the reverberatory or the blast furnace. For example, otherwise valuable ore deposits may be situated in a district so remote from, or inaccessible by, railway that the cost of get- ting coke for smelting, or of transporting the ore to a smelter, is pro- hibitive. If there is sufficient water power at hand, from which electric power can be developed at a reasonable cost, and this electric power is used for smelting the ore in an electric furnace, with subse- quent bessemerizing, if necessary, the concentrated product may be

Jan 1, 1915

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By W. R. Crane

THE support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident then that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 9, 1924

By E Ruhanen, S Kauvosaari, M Kosonen, C Meintjes

The Yara Siilinjärvi plant is located in the central part of Finland. Siilinjärvi is Western Europe's only apatite mine and annually it produces 1 Mt of apatite concentrate, which creates approximately 10 Mt of tailings.At the beginning of 2017, tailings handling in Yara Siilinjärvi was brought to a new era, by replacing the conventional tailings storage facility with a new tailings treatment plant. The new high-density tailings disposal system with two paste thickeners increased the percentage of solids in the slurry from 45–48 per cent to 66-68 per cent, making it possible to deposit as a paste. This extended the life-span of the current tailings storage facility by 15 years; from 2020 to 2035.This paper presents the storyline of the Yara Paste Plant Project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After some successful pilot trials, the final process design was implemented. Process instrumentation and automation played a key role in the project, as the aim of the Yara Project was to make the plant operable remotely from the main plant. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances.This paper discusses the results from the Yara site since the new tailings treatment plant commenced. Some of the main points are that the operation has been running consistently with an underflow solids content of 66-68 per cent, with average beach slope angles of 3.5 degrees in the tailings disposal area. This control system additionally facilitates minimum use of flocculant, which delivers significant savings to operating costs. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the Paste Plant. During the first year of operation, the plant’s availability has been very good, over 97 per cent.Currently, the plant still has its own staff working there during the daytime, but the Paste Plant is now already operated remotely during the night shifts. The long-term goal is to gradually transition into operating the plant completely remotely.CITATION:Ruhanen, E, Kosonen, M, Kauvosaari, S and Meintjes, C, 2018. Optimising the operation of paste thickening at the Yara Siilinjärvi Plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 297–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Krystyna Raszka, Jerzy Iskra

The paper presents results of spectrophotometric investigations concerning the adsorption of sodium oleate on silicon carbide in the presence of the cations of multivalent metals, applying the ATR IR technique with computer-aidedprocessing of the spectrum. The analysis of these spectra indicates the occurance of distinct OH and COOH bands in the pH range in which the hydroxy complexes of metals of the type MeOH+ and MeOH++ reach in the respective cases the highest concentration in the solution. The correlation of these results with those of flotation, measurements of the zeta potential confirms the proposed mechanism of activation of the flotation of silicon carbide, applying sodium oleate as a collector, the collection taking place over the adsorption of hydroxy complexes of the type MeOH+ and MeOH++

Jan 1, 1995

By M. H. Loveman

The orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°201, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Syrnes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 anually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The . closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 1, 1917

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By S. B. Christy

The fact that many millions of gold have been extracted by the cyanide process, during the last five or six years, from South African tailings which could not be profitably worked by any other method previously tried upon them, lends a peculiar practical interest to this branch' of metallurgy. Numerous writers have recently made valuable contributions on the process without exhausting the many complexities of the subject. Among the first American writers on the subject in its modern aspect were two former students of the University of California, Mr. Louis Janin, Jr., and Mr. Charles Butters. Young Janin was one of the first to enter this field, and performed much useful experimental work in the early stages of the history of the process. At about the same time, Mr. Charles Butters, who had left California to erect chlorination works for the Robinson mine at Johannesburg, became interested in the cyanide process, and, after getting the chlorination plant in working order, put up, for working the tailings from the Robinson mine, a cyanide plant which achieved the first large-scale success ever made with this process. The papers which Charles Butters, together with John E. Clennell and Edgar Smart, have contributed on the chemistry of the process, were among the first to give any adequate idea of its nature.* Another important contribution to the literature of the subject is the paper of Dr. A. Scheidell, published in 1894 as a " Bulletin of the California State Mining Bureau." This contains an admirable summary of the state of the art at the time of its publication.

Jan 1, 1897

By G. M. Brownell

Introduction The Flin Flon mine is located on the boundary line between the provinces of Manitoba and Saskatchewan at a point about four hundred miles northwest of Winnipeg. A branch of the Canadian National railway provides the town of Flin Flon with direct transportation facilities. The property was staked in 1914 and, after a considerable amount of exploration; the Hudson Bay Mining & Smelting Company was organized and brought the property into production in November, 1930 (1). Mining is carried on by open pit and underground methods at the rate of about 4,400 tons per day. Production for the year 1934 was: 99,334 ounces of gold; 1,335,319 ounces of silver; 37,486,054~pounds of copper; and 49,427,280 pounds of zinc; in addition to small amounts of cadmium and selenium. The Flin Flon deposit is one of the largest low-grade ore deposits in Canada with complete hydro-electric and metallurgical plants for the production of blister copper and electrolytic zinc. Previous Work The development of the Flin Flon mine into one of the major mining operations in Canada has created a need for a more detailed geological study of the area. Practically all of the information published to date concerns the general surface features. It is the purpose of this paper to deal more specifically with the ore-body and its relationship to the enclosing rock as revealed by studies made possible through recent underground development. The earliest published report on the area is by E. L. Bruce (2), who made a reconnaissance geological investigation of the region for the Geo-logical Survey of Canada in 1914 and established the main. petrological units. Several years later the area immediately around Flm Flon was mapped in greater detail by F. J. Alcock (3). In the summer of 1934, the area of Missi sediments to the north and east of the mine was studied by J. W. Ambrose. His report has not yet appeared in print but his findings are of importance.

Jan 1, 1935

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement' affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911

By Peter Price

Introduction The Horne mine, the property of Noranda Mines, Limited, has in the last six years become one of Canada's leading gold and copper producers. Since the smelter was blown-in during December, 1927, up to the end of 1933, it has produced approximately 1,200,000 oz. of gold and 35O,OOO,OOO lb. of copper. The property is situated within an area occupied entirely by pre-Cambrian rocks and characterized by the complexity of rock types and structures common in such terrain. But apart from this the mine also presents other features of unusual interest in the size, number, and variety of the ore-bodies, the mineralogical associations, and the rather exceptional values both in gold and copper. It is not surprising, therefore, that a study of the geology of the mine should bring to light many interesting problems. The present paper summarizes, as concisely as possible, the results of such a study. Actually, it is a much abridged version of a more comprehensive and detailed paper completed by the writer a year ago (1), but embodying certain corrections and additional data made possible as a result of further development at the mine and of field work carried out during the summer of 1933. Owing to limitations of space, the paper is, in the main, a presentation of conclusions arrived at in the course of the study. Much of the supporting evidence cited in the thesis referred to has, of necessity, been omitted here.

Jan 1, 1934

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators' and Miners' organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929

By George Stone

THE stack gases from regenerative furnaces are very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300° C. (572° F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450°. The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the .boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 10, 1913

By Edwin A. Sperry

The use of steam-stamps in the crushing of ore for the purpose of amalgamation has been very limited, and little has been written on the subject. As the writer has been operating a mill of this kind during the past year, it is possible that he may be able to present a few points in regard to mill-practice in this line which will be of interest. The mill herein referred to contains two Tremain steamstamps, a more detailed description of which will be given below. A bond and lease had been taken on a property on Cross mountain, Gunnison county, Colo., and the parties operating wished to prospect it thoroughly and did not wish to ship out the ore, owing to high freight-rates. They looked around to find some mill that would answer the purpose and not be too expensive. The steam-stamp in question was finally decided on, and the writer was employed to erect and operate it. The economy of construction was demonstrated at the outset. The stamps were dropping within ten days from the time that the machinery was unloaded on the ground. A large portion of this period was consumed in waiting for supplies and fittings which should have been on the ground at the Hame time with the machinery. Ore.—The ore to be treated was a mixture of white, porous quartz, with the decomposed and undecomposed oxides of iron and manganese in varying proportions, from the pure white quartz to solid pieces of the oxides. It appeared to be the product of replacement in a soft dolomite at or near the line of contact with a dike of porphyry. On careful examination with the aid of a microscope it was found that the gold was in the form of an extremely thin film over the surfaces of the quartz, making only a bronzy-yellow coating, quite readily distinguished from the film of iron oxide, which was also present. Mill.—The mill was constructed on the usual plan, with the ore-bin above and against the hill, which was cut into for the

Jan 1, 1897