Search Documents

By R Robinson

Modem occupational health practice can be described as the fitting of work to the individual and each individual to his job; perhaps a non-traditional way to view occupational health. This two-component description is achieved through the development of programs to implement and monitor specific job procedures, from the monitoring of unwanted exposures to contaminants to the auditing of mine sites. This paper is about such programs. Some attempt must be made to evaluate the effectiveness of the program and several performance indicators which are intended to measure the effectiveness of such a program are offered.

Jan 1, 1994

By H. L. Talbot, R. S. Young, A. Golledge

THE differentiation of, oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a complex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite satisfactory for routine control purposes. EXPERIMENTAL For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to - 200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyromorphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1947

By S. Rupprecht, G. Rapson

Long blast hole drilling has been successfully implemented since the 1950s in caving operations, steeply dipping wide reefs and boxhole/raise developments worldwide. However, when applying long hole drilling to narrow tabular reefs, the challenges of achieving high economic drilling rates, combined with acceptable accuracy and appropriate powder factors have yet to be overcome. The focus in this paper is the selection, application and optimization of long hole drilling equipment at mining operations shallower than 2 000 meters. The drilling, blasting and cleaning operations have to be optimized as a process if maximum production at minimum per unit cost is to be achieved. For this to be possible, it is essential that the mine design and layout match the mining process being implemented. The critical parameters affecting the sustainable implementation of long hole drilling in stoping applications for platinum mines are improved safety and higher production rates compared to conventional methods. In terms of drilling, both top hammer and down-the hole hammer configurations have been considered. For economic drilling, the benefits of monitoring and optimizing performance (i.e. drill bit rotation, thrust, and percussive power) for specific rock types are discussed. While the drive is for longer, more accurate, smaller diameter holes to reduce drilling costs, the design of appropriate blast hole patterns and the corresponding charging and initiation systems is crucial for success. The effect of hole diameter and pattern on the powder factor, when comparing small diameter, shorter holes versus large diameter, longer holes, is a major factor in achieving good blasting results. Once appropriate drilling and blasting have been implemented, the cleaning process becomes a potentially critical operation to ensure the production, cost and safety goals are met. Hence, the blast hole pattern and charge have to be integrated for optimal fragmentation to suit the cleaning cycle for maximum production output. Providing that long blast hole drilling is applied as a process in a planned, committed and well-managed manner, the benefits in safety, production and cost over conventional methods should be achievable. However, if the implementation process is not planned and supported by all parties concerned, it will not be possible to succeed in the new operation. Hence, an implementation or roll-out plan of new technology is crucial for success.

Jan 1, 2004

By Ross Gilders, Leo Cheung, C. David Desjardins

"For the past twenty years significant progress has been made in bacterial leaching. In fact, a recent article in the Northern Miner has cited that nearly all new copper production is based on bioleaching. The bacteria that play the predominant role in bioleaching is an obligate chemolithoautotroph called thiobacillus ferrooxidans. These bacteria thrive in areas rich in sulphide and prefer low acid media. In the simplest sense, they metabolize sulphide converting it to sulphate either as acid or as soluble metal sulphates. This process is well known because these bacteria generate acid mine water. Over the last five( 5) years, we have been carrying out development work on creating optimum bioleach conditions for the extraction of metals from sulphide rich ores and concentrates. Recently, a study was carried out on a byproduct sulphide concentrate produced in a tin flowsheet developed for the Mt. Pleasant Mine of ADEX Mining Corp. The objective was to determine whether a bioleach process might successfully leach this sulphide material which contains copper, zinc, iron and, what is more important, trace metals such as Indium, Gallium, and Bismuth. The current work describes the successful recovery of these metals achieving extractions of more than 80% by applying bioleaching techniques. An overview of this technical program forms the basis of this paper.IntroductionBio-Oxidation of metal sulphides has emerged to be one of the leading edge hydrometallurgical processes for the economic extraction of metals from ore and concentrates. The fundamental process involves the bacterial assisted oxidation of sulphide to sulphate yielding metal sulphates which can be subsequently leached by conventional means. The bacteria that play the predominate role is an obligate chemolithoautotroph named thiobacillus ferrooxidans (TF). These bacteria thrive in areas rich in sulphide and occur naturally worldwide. In fact, TF is responsible for generating acid in water (acid mine water) from exposed sulphide surfaces primarily through the oxidation of pyrite. TF bacteria thrive under the proper conditions of temperature and oxygen supply in the presence of sulphides and populations in excess of a million per millilitre (ml) of solution are achievable. Typically, at room temperature, the bacteria will bio-oxidize in a pH range of 1.0 to 3.0. Today, bio-oxidation has been applied commercially with great success for the extraction of uranium, copper, and gold."

Jan 1, 1996

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

By William A. Beck

"The Old Cline mine, also known as the Old Cruse mine, was first worked for gold in1895. The property was opened by several shafts and trenches; and some stoping has been done, producing several cars of copper-gold ore in the early nineteen hundreds. Chalcopyrite is visible in selected samples; and, with the aid of a mineralite, several samples showing a considerable amount of scheelite were found on the old waste dumps.The mine is in Township 6, Cabarrus County, N. C., 5 miles north of the village of Mount Pleasant, 10 miles northeast of Concord, and about one-half mile south of Watts Crossroads. It is one-fourth mile east of the county road.When examined, the property was owned by H. F. Tompkinson, Concord, N. C., and was leased, with option to buy, by L. Nash. Titles of record were not investigated.As stated above, the Cline mine was first worked in 1895. The property was Purchased in 1902 by J. A. Clark and A. A. Smith of Atlanta, Ga., and worked for gold and copper. No record is available of the quantity of ore removed during these operations.A Bureau of Mines mining engineer3/ examined the mine as, a copper prospect on October 13, 1944.The Cline mine is in an area characterized by flat to rolling topography, dissected by many streams and rivers. It lies in the Piedmont Plateau and Varies in elevation from 700 feet to 800 feet. The surrounding country is partly wooded and partly cleared farm land.A quartz vein occurs in country rock of quartzite and greenstone.4./ The ore occurs in a series of quartz lenses, having a width of 1 to 3 feet and dipping about 750 NE, and striking N. 300 W. All these lenses have fairly sharp boundaries and in some cases are entirely separated from each other, while at other times they are connected by thin stringers of quartz. They can be traced for 1,000 to 1,200 feet by a series of shafts and test pits."

Apr 1, 1946

The results of a systematic geochemical survey of rare elements are applied to elucidate genetic relations in a suite of rocks and to predict the probability of mineralization. The geology, radioactivity, major element geochemistry and classification of the main intrusives are described. The distribution of a group of rare elements, their concentration trends and the bearing these have on the emplacement sequence of the rocks are considered in some detail. The guides for exploration in the Pilanesberg that emerge are listed and some areas which substantiate predictions are described briefly. It is concluded that a study of rare element trends can make a considerable contribution as an exploration tool and for clarifying relations between the members of rock suites.

Jan 1, 1986

By Song Yongxue

During the design and operation stages of a block caving project, a large amount of research and development work has been undertaken in the Tongkuangyu Copper Mine. This paper presents the research achievements from these studies, including a rock mass quality evaluation method, cavability prediction, fragmentation evaluation, caving mechanisms, a computerised production scheduling model and the optimised draw control system. The main features of the block caving system in the Tongkuangyu Copper Mine are also discussed.

Jan 1, 2000

[ARTICLE I. NAME AND OBJECT Section 1. This Society shall be known as the Society of Petroleum Engineers of the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. Section 2. The object of the Society of Petroleum Engineers shall be to furnish a medium of cooperation among those interested in the petroleum-natural gas industry an to promote the advancement of this branch of mineral technology through meetings to stimulate the preparation, reading, discussion and circulation of papers connected therewith. ARTICLE II. MEMBERS Section 1. Any person who is a member of AIME may become a member of this Society by the specified process. Section 2. Local organizations may be formed by the Society of Petroleum Engineers as subsidiary units, the membership of which shall be subject to and in accordance with the by-laws of the Institute.]

Jan 1, 1961

By E. William Heinrich

With the mounting emphasis on unconventional energy sources, total consumption of lithium minerals will increase significantly in the next decade. The recent development of the lithium battery, for example, may greatly boost the demand for lithium metal. At the same time, the growth in the ceramic, glass, and chemical industries is bound to increase the demand for lithium minerals. In fact, the entire consumption or utilization breakdown of lithium minerals will change considerably from its current pattern. Briefly, today's market for lithium minerals' can be grouped into three categories: (1) Lithium concentrates. Accounting for 57% of market use, these concentrates are beneficiated Li-A1 silicates for ceramic, glass, and glass-ceramic raw materials. The concentrates are chiefly spodumene; inverted iron-depleted beta-spodumene; and petalite or its isochemical decomposition product spodumene + quartz intergrowth ("squi"). In the past, lepidolite has also been used.

Jan 9, 1974

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the GEORGIA PRODUCTION UNITED STATES PRODUCTION IMPORTS Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

By G Harbort, T Georgiev, M Phillips

Phu Bia Mining Ltd, a subsidiary of Pan Australian Resources Ltd owns and operates the Phu Kham copper concentrator located in the Xaysomboun District, Lao PeopleÆs Democratic Republic. Construction and commissioning of the 12 Mt/a copper concentrator and associated facilities was undertaken by Ausenco Ltd and handed over to Phu Bia Mining Ltd in April, 2008. The first copper concentrate was produced in April 2008 and the ship carrying the first shipment of copper concentrate set sail 27 July 2008. Nameplate mill throughput was reached in August, 2008 when 1 020 000 dmt of ore was treated in the milling and flotation circuit. The Cu-Au mineralisation is contained in skarn and stockwork mineralisation and is interpreted as a distal expression of a conventional porphyry copper-gold system. Copper mineralisation is principally in the form of chalcopyrite with lesser bornite. Gold occurs as small grains, typically associated with copper minerals. In the upper portions of the orebody, oxidation and water table movements have resulted in near surface leaching of the copper and below the leached zone, supergene enrichment resulted in chalcocite mineralisation. The circuit operates with a semi-autogenous grinding (SAG) û ball mill circuit, feeding a bank of OK200 rougher cells. Rougher concentrate is reground in an IsaMill prior to entering a cleaner circuit consisting of three stages of cleaning and one stage of cleaner scavenging. The concentrate typically assaying 24 per cent Cu and 6 - 7 g/t Au is hauled for over 1000 km across the border to the Port of Sriracha in Thailand, and stocked in sheds at the wharf from which it is shipped to various Asian smelters. This paper discusses the successful commissioning and ramp up to design tonnage and metallurgical performance. In addition, a program to optimise both the comminution and flotation circuit is detailed with reference to grinding efficiency, flotation residence time and size by size mineral recovery.

Jan 1, 2009

By Andrew R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past; from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

May 1, 2002

By S. J. Macnaughton

The Olympic Dam deposit in South Australia contains 2% copper and 0.06% uranium, which are present as bomite, chalcocite, chalcopyrite, uraninite, coffinite and brannerite. The copper is principally recovered using flotation. The flotation tailings, which contain the bulk of the uranium, and typically 0.3% copper, are leached using sulfuric acid and an oxidant at atmospheric pressure. This paper describes the results from a detailed investigation of the leaching behaviour of this ore. The influence of acid strength, Fe3+ concentration, redox potential and temperature on the dissolution of uranium and copper minerals was studied. Experimental data were obtained from extensive batch leach tests. Mineralogical studies, including SEM analysis of individual mineral grains, were also carried out. The maximum extraction of uranium determined experimentally was in good agreement with that predicted from SEM determination of the proportion of refractory brannerite in the ore. The leaching rate of copper was found to be independent of acidity over the range 20 g L-' to pH 2.0, but was strongly dependent on temperature and Fe3+ concentration. Uranium extraction showed a weak de endence on acidity, Arrhenius temperature dependence and a complex co-dependence on F>+ concentration and redox potential. A kinetic model has been developed, which predicts copper and uranium dissolution. This model will be incorporated into a more comprehensive model that can be used to predict leach performance and reagent consumption for specific ore samples.

Jan 1, 1999

By Chuck Edwards

"The development of two large, high-grade uranium projects has been proposed for northern Saskatchewan. The projects are now under review by a joint federal/provincial panel. The McArthur River project is owned by the McArthur River joint venture (Cameco Corporation 53.991 %, Uranerz Exploration and Mining Limited 29.775%, Cogema Resources Inc. 16.234%) and operated by Cameco. Cameco proposes to mill the McArthur River ore at the existing Key Lake mill. The Cigar Lake project is owned by the Cigar Lake joint venture (Cameco Corporation 48.75%, Cogema Resources Inc. 36.375%, Idemitsu Uranium Exploration Canada Ltd. 12.875%, Korea Electric Power Corporation 2.000%). The Cigar Lake joint venture proposes that Cameco operate the Cigar Lake mine for the owners, and that Cogema mill the ore at their McClean Lake mill, now under construction. Proposed systems provide safe mining and ore handling, and allow the milling of McArthur River ore at Key Lake and Cigar Lake ore at McClean Lake. This avoids the disturbance of new sites for milling and tailings disposal.The McArthur River and Cigar Lake deposits are the largest known high-grade uranium deposits in the world. The ore grades at McArthur River and Cigar Lake are at least 100 times those that are mined elsewhere. It is proposed to mine these deposits using remote underground mining methods, to crush and grind the ore underground, to pump a thickened ore slurry to surface, and to transport it in special containers by truck to the mills.During all mining and processing stages the ore is fully contained. Radon emission is controlled by positive ventilation of all process vessels, with the process ventilation backed up by the primary mine ventilation system. Radiation is controlled by heavy steel pipe and vessel walls, concrete walls and sometimes lead sheeting."

Jan 1, 1997