Search Documents

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By P. E. L. Balestra, A. O. Filmer

The kinetics of the reactions involved in the non-oxidative dissolution of nickel concentrate in hydrochloric acid were studied by electrochemical and powder-leaching methods. It was found that the rate of non-oxidative dissolution increases with a cathodic shift in the mixed potential, which can be achieved by an increase in the nickel-to-sulphur stoichiometric ratio at the reaction surface. An unactivated concentrate with a sulphur content of 36 per cent exhibited a mixed potential of +O,3V (SCE) and could not be leached satisfactorily in 3 M hydrochloric acid at 60°c. When activated material (18 per cent sulphur) was leached, it had a mixed potential of -O,3V, and high iron and nickel extraction rates. Results reported by other workers on the non-oxidative dissolution of sulphides are explained in terms of the mixed potentials at which dissolution occurs.

Jan 1, 1981

By Margaret N. Maxey

For the past quarter century, it is fair to say that the political agenda of Western industrialized societies has been driven by those opposed to forms of economic growth providing sustenance to a growing population. They regard growth as the major threat to their social philosophy which champions a wholly "new ethic of biocentric equality" or "living as if Nature mattered." This ethic demands that "a violent, plundering humankind" must abandon its alleged rape of Planet Earth and derive its ethical norms from pre-existing harmonies and fragile, precarious balance present in Nature. A Green political agenda appeals strongly to deep longings shared among many people whose temperament seeks tranquillity in a world of wild natural beauty uncluttered by dependency on tools and experts and specialists. According to proponents of the Green philosophy, our world is pregnant with enormous problems. Armed with expanded political powers, regulatory guardians at state and local levels have mustered their forces with shotguns cocked, poised to prod an ignorant and lazy citizenry to the altar for an exchange of vows with Environmental Ethics. Social engineers have skillfully discredited the traditional role of professionals in scientific engineering who are summarily dismissed as the failed architects of an industrial system pillaging the earth. They stand accused of producing unmanageable offspring - from mining minerals and energy resources to disposing of toxic wastes - whose disputed parentage and expectant crimes against humanity must be prevented by removing them from normal custody. Green critics claim that markets cannot be given custody of industrial offspring - pollutants, wastes, land-use abuses. Markets appear to have failed to provide equity to present and future generations. The only custodian with sufficient coercive power seems to be the regulatory bureaucracy. The upshot is a stark Hobson's choice - Shotgun Wedding vs. Custody Dispute. It derives its fateful predestination from an uncritical acceptance of several preconceptions which currently undergird the altar of Sustainability characterized by its acolytes as "a new and exciting doctrine." It is significant that Limits to Growth slogans of the 1970s have been displaced in the 1990s by the more palatable language of Sustainability. As a policy recommended to forestall an impending doom, Sustainability derives its credibility from dire predictions of global warming, ozone depletion, acid rain and the like. The Rio Declaration announced to the world in June 1992 that, although energy is essential to human well-being, its production and consumption in wealthy industrialized nations is unsustainable. It called for a complete overhaul of energy systems with nothing short of a total replacement of fossil fuels, uranium fission reactors, and large hydroelectric projects by means of so-called renewable energy sources, augmented by coercive regulations to force conservation and limit consumption demands. The social and political consequences of such a sweeping

Jan 1, 1995

By P. C. Richards

"Future Integrated Gasification Combined Cycle (IGCC) power plants will have superior environmental performance and unmatched efficiency.The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an IGCC plant. SCGP flexibility has been demonstrated for feeds ranging from bituminous coals to lignites and petroleum coke, and the process is ideally suited for combined cycle power generation, resulting in efficiencies of 42% to 46% (LHV).In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology is being built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N. V. Sep). The plant is scheduled to start up in 1993. IntroductionBasic ConceptShell's experience with gasification dates back to the 1950s, when the first Shell Gasification Process was commissioned with oil as feedstock. There are now over 140 SGP gasifiers licensed. The experience gained on oil gasification provided a firm theoretical and practical base for the start of coal gasification process development in 1972.At that time, there were serious concerns about the future availability and price of crude oil. Coal gasification (making carbon monoxide and hydrogen by the partial oxidation of coal) was considered to be an important option for refinery applications, because the synthesis gas (syngas) produced can be used as:• a chemical feedstock for making transportation fuels and chemicals;• a source of hydrogen (making use of the water gas shift reaction) for upgrading petroleum products; and• a fuel for heating process streams and/or generating electricity."

Jan 1, 1994

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

Little information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's," ' Kick's,%nd Bond's' theories. Theories by Bond and Wang," Lineau,' Hatch,' Roller," and others were not considered applicable. Those used in this investigation may be expressed mathematically as follows: [ ] The above equations were employed to determine values of KK, K for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement.

Mar 1, 1956

In the Massif du Sud ophiolite complex platinum group elements occur predominantly as ultrafine-grained inclusions of rutheniridosmine, laurite and iridosmine. These form primary inclusions less than 5 to 10 um in diameter within chromite in podiform chromitite fringed by dunite, and emplaced subsequent to solidification of the host harzburgite. There is no specific association with trace inclusions of transition metal sulphides. The crystallization of then: Ir. Os and Ru minerals may have occurred concomitant with hromite, perhaps related to more reducing conditions produced by crystallization of the chromite. The Ir, Os. and Ru show pronounced fractionation from Pd, Pt and Rh expected to be also present in the mantle source rock. The dunite shows evidence of metasomatic origin from adjoining harzburgite, and the possibility of selective crystallization of the Ir sub-group elements suggests that Pd, Pt and Rh may have been transported elsewhere.

Jan 1, 1989

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

The international scientific and engineer-ing community is being challenged to take advantage of the opportunity offered by the U.N. International Decade for Natural Disaster Reduction (IDNDR) program to reduce rapid onset geological hazards along the Pacific Rim. Natural disasters observe no national boundaries; international cooperation offers the best opportunity to reduce the losses these catastrophic events create.

Jan 1, 1990

By S. K. Tarby, V. S. Robinson III

A number of experimental determinations of the vapor pressure of liquid silver have been reported in the literature. 1-8 This communication presents additional data for the vapor pressure of liquid silver measured in the temperature range of 1450° to 1600°C and summarizes the results of previous investigations. The results reported here were obtained as part of a

Jan 1, 1969

"In order to increase control over blasting, it is important to identify the imperative mechanismsand to quantify their participation during the rock fracturing process. The useful energyreleased by the detonation of an explosive is split into shock and gas energies. The relativeimportance of these two energies in the rock fracturing process is still an area of active debate."

Jan 1, 1999

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10?15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed, and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2013

By David B. Gladwin

Regional characteristics in the coal resource base have resulted in application of different mining methods across Canada. Longwall methods predominate in eastern Canada, whereas open pit, hydraulic and room-and-pillar methods are utilized in the west. Both provincial and federal agencies have regulatory responsibilities and both also share in the development of R&D programs. This paper outlines the scale and scope of the various agencies involved with health and safety R&D in our expanding coal mining industry. Specific R&D activities in ventilation, dust control, explosion hazards, tunnel boring, strata control and truck braking, which form part of the national program, are outlined.

Jan 1, 1982

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world&apos;s production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By K:-I. Rhee

The recovery of tellurium from Te-cement obtained during the processing of copper anode slimes was carried out by a series of hydrometallurgical processes, i.e. leaching Te-cement in NaOH solution, precipitation of impurites with the addition of Na2S followed by direct electrowinning of tellurium in NaOH solution. The optimum conditions for each process were determined and discussed in terms of various parameters associated with each step to maximize the recovery and purity of tellurium. The final purity of tellurium from electrowinning in alkaline solution was found to be more than 99.9 %.

Jan 1, 1997