Search Documents

By Calvin R. Davis

The bucket elevator is probably the oldest known form of conveyor. Its history can be traced back to the days of Babylon where wicker baskets lined with a natural pitch and fastened to ropes operating over wooden sheaves turned by slaves, were used for the elevating of water into irrigation ditches. It is not unnatural for the bucket elevator to be the first in history, for even today engineers and designers recognize that well designed, correctly applied bucket elevators offer unequaled advantages over other bulk material elevating methods. The bucket elevator's vertical design saves valuable floor space. It provides flexibility of machinery layout with lowest initial capital expenditure, which is its principal advantage. While the advantages of the bucket elevator have long been recognized, there has been a tendency to lean away from its use because of high maintenance without reliability. CHAIN Belt Company found that the bucket elevator, if correctly applied, can be built to be as dependable and reliable as any other piece of machinery in today's modern processing plants. It is not difficult to understand why the bucket elevator is looked upon sometimes as a necessary evil in the material handling system. Very little has been published or written about the specific use or application of bucket elevators other than in manufacturers catalogs. Most of today's elevator application was set forth at the turn of the century by Hetzel (1). There have been many improvements made in the manufacturing techniques of elevator components, improvements in material selections, all which can be used to improve today's bucket elevator. To best understand the improvements which have taken place recently in the design and application of bucket elevators, an understanding of basic elevator principles is desirable. In general, it can be said that bucket elevators are classified into two basic types : (1) centrifugal discharge and (2) continuous. Elevators in use today are either of the centrifugal discharge type or the continuous type, or a combination of both in special applications.

Jan 1, 1958

By R. L. Marek

[An important problem in the efficient conduct of industry is that of helping the individual employee to formulate in attitude toward his work which will result in the reduction of accidents and the promotion of safety. Perhaps nowhere is the need greater for this type of psychological training of carefully selected men than at oil refineries whore both the raw materials and the finished products are highly inflammable and explosive in nature. However, the refinery organization usually is well adapted to educational safety activities -- much more so than in the producing, pipe line, and marketing departments where the personnel are more or less scattered; but the sore general principles of conduct hold true in any industrial organization. This problem of directing the attention of tie employees to their specific tasks or helping them to control and frequently eliminate hazards engendered by adverse mental attitude or emotion is met most satisfactorily by carefully selecting applicants and placing theta at jobs for which their ability best fits them. The subsequent training of these carefully selected employees to assure their Most effective work in accident prevention may be accomplished in a variety of gays, ouch as by personal supervision and instruction, inspections, drills, and by the studied use of well thought out safety pamphlets and posters.]

Jan 1, 1932

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By Larry H. Heflin

The Washington Metropolitan Area Transit Authority's Wheaton Station and tunnel design was completed and offered for bid in the Spring of 1983. The format was unique to the Authority: a four part, four fiscal year contract developed in response to funding limitations with construction divided into four stages allowing the maximum amount of work to be done each year for the funds available. The bid was based on the entire contract, but was orginally awarded for only the first year's work. Each year's work had a maximum funding limitation thus safe guarding the Authority from a grossly unbalanced bid. The Authority's estimate for this work was $83,871,524. The low bid came in at 61% of this for a total low bid of $51,512,058. The low bidder was ILBAU America Corporation whose home offices are in Austria. Following receipt of the bids (and resolution of objections cited by other bidders who felt that the job could not be done for the $51 Million dollar figure), a Notice-To-Proceed was given on October 5, 1983. The construction contract allows a Value Engineering Change Proposal, called a VECP which is initiated and developed by the contractor to change the drawings, specifications or other requirements of the contract. Among other things the VECP should decrease the contract price while maintaining the service life, reliability, ease of maintenance, and standardized features and appearance and not require an unacceptable extension of the contract time. A VECP must estimate the amount of the net savings

Jan 1, 1985

"The research aimed at solving the problem of measuring instantaneous local physical quantities for multiphase flows in mineral processing, which are common in minerals industry and with significant challenges. Due to the lack of proper measurement tools currently in minerals industry, multiphase flows (such as in flotation cell) are treated as in a “black-box”. It is crucial to develop measurement technique by which the acquired processing data can be used for process optimization and control. By measuring the conductivity distribution across a measurement area, Electrical Resistance Tomography (ERT) has been adopted by many researchers to monitor and investigate many processes involving multiphase flows in other industry sectors. A compact ERT probe was built and then used to measure the conductivity distribution within a few flotation machines. In a flowing foam flotation column, the results showed that ERT can accurately measure the change of liquid content (high conductivity fluid distribution). In another part of work, based on the Green-Kubo relations, ERT can measure turbulence via the fluctuation of conductivity caused by bubbles moving through the measurement area, changing the density of the fluid. The tests with the Metso 3 m3 RCS flotation cell were also carried out for turbulence measurement under different air rates and impeller speeds. The results of flotation cell from ERT measurement showed that varying impeller speed had more pronounced influence than changing air rate. When impeller speed is increased, the size of the high turbulent zone increases. ERT is a powerful technique that has the potential to be used for a wider range of applications. The future work will be carried out with more case studies and expanded to more processes such as leaching process, high temperature flows in further downstream production chain (steel making process and alloy manufacturing process).INTRODUCTIONMultiphase flows constitute a majority of the naturally-occurring and industrially-relevant flows, especially in mineral processing. Some of the measurement techniques have been used for the study of fluid characteristics. Optical techniques such as Laser Doppler Anemometry (Kyselaa et al., 2013) and Particle Image Velocimetry (Nobach and Bodenschatz, 2009) can produce accurate measurement results with high spatial and temporal resolution, but their applications are limited to transparent flows. Hot wire probes (Amini et al., 2013) have high spatial and temporal resolution in turbulence quantification, but they are susceptible to environmental factors."

Jan 1, 2018

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By J. H. Brophy, S. J. Michalik

A constitution diagram for the system Mo-Ir has been determined. The maximum solubility of iridium in molybdenum is 16 at. pct at 2110ºC and decreases to less than 5 at. pct at 1500°C. The solubility of molybdenum in iridium is 22 at. pct. Three intermediate phases appear in the system: 8 MoJr, having the p-tungsten structure; a phase, a cornplex tetragonal structure; and the hcp ? phase. Metallography, melting point determinations, X-ray diffraction and fluorescence, and electron micro-probe unalyses were employed in establishing the diagram. PREVIOUS to the present investigation, the intermediate phases in the Mo-Ir system were identified, but no detailed account of the phase diagram has been reported in the literature. Raub1 investigated alloys of Mo-Ir over an extensive range of composition between the temperatures of 800º and 1600°C. The in-termetallic compound MosIr was found to exist with nearly pure molybdenum, as the solubility of iridium in molybdenum was not detectable parametrically in this temperature range. MO3Ir was found to be iso-morphic with a ß-tungsten type structure, having a parameter of 4.959Å. An intermediate hcp phase, designated as the ? phase, ranged in composition from 52 to 78.5 at. pct at 800ºC, and from 41 to 78.5 at. pct Ir at 1200°C. Parameters noted for the ? phase were as follows: at 42.7 at. pct Ir, a = 2.771i0, c = 4.4366, c/a = 1.601; at 78.5 at. pct Ir, a = 2.736A, c = 4.378A, c/a = 1.600. Molybdenum was found to be soluble in iridium up to 16.5 at. pct Mo (83.5 at. pct Irj, with the parameter of iridium increasing to 3.845A at the solubility limit. Knapton,2 who investigated alloys between 15 and 85 at. pct Ir, essentially agreed with Raub's data, but, in addition, found a a phase in as-melted alloys near 25 at. pcto Ir. The oaphase lattice parameters were a = 9.64Å, c = 4.96Å, c/a = 0.515. The a phase was replaced by the 8 -tungsten phase on annealing at 1600°C. Knapton concluded that the a was stable only at elevated temperatures, and placed the composition of the a phase at approximately 30 at. pct Ir. The intermetallic compound Mo3Ir, with a lattice parameter of 4.965A, was included among the 8-tungsten structures reported by ~eller.' Matthias and Corenzwit,4 and Bucke15 studied the superconducting nature of MosIr, and reported a superconducting transition temperature of 8.$K. The present investigation describes the phase relationships in the Mo-Ir alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURES Alloys for the determination of the phase diagram were prepared from powders. Commercial 99.9 pct Mo from Fansteel Metallurgical Corp. and 99.9 pct Ir powder from J. Bishop and Co. Platinum Works were used. The powders were weighed to nominal compositions, mixed, and then pressed, without binder, into compacts weighing 4 to 6 g. These were presintered in uacuo between 1200' and 1400°C for 1 hr, to reduce the degree of spattering during subsequent arc-melting. The compacts were arc-melted in a nonconsumable tungsten electrode furnace six times on alternate sides on a water-cooled copper hearth in an atmosphere of zirconium-getter ed argon at 500 mm of mercury pressure. In almost all cases, this procedure yielded buttons of satisfactory homogeneity. The composition of all melted buttons were confirmed by X-ray fluorescent analysis using the experimentally determined ratio of the iridium La1 line intensity to that of the molybdenum Ka1 line as a function of composition. In this determination four alloys analyzed by wet chemical methods were used as standards. An uncertainty range of ±1 at. pct has been attributed to all indicated compositions. All heat treatments and solidus measurements were carried out in tantalum resistance heating elements in vacuum conditions of 10-4 to 10-5 mm of mercury. A detailed account of this procedure has been reported by Schwarzkopf and Brophy.8 In the heat treatment and solidus measurements of iridium-rich alloys (50 at. pct Ir or greater), a tungsten lining was inserted into the tantalum resistance heating element because of a eutectic reaction which occurs between iridium and tantalum at 1948ºc.7 Heat treatments and solidus measurements carried out at compositions less than 40 at. pct Ir both with and without tungsten linings within the resistance

Jan 1, 1963

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By B. H. Caudle, A. D. PUCKETT

This paper summarizes precent knowledge of the ignition qualities of pure hydrocarbons likely to be present in modern Diesel engine fuels, as shown by an extensive search of the technical literature. The report also discusses the possible significance of cetane number and hydrocarbon struc- ture. Cetane or cetene numbers, and other physical properties, are tabu- lated for about 100 hydrocarbons, and a bibliography is appended. In recent years the Diesel engine has enjoyed increasing popularity due to its dependability, inherent characteristics of fuel economy, and the fact that it operates on a fuel that hitherto has been available in comparatively large quantities at a low price. These qualities have en- abled the compression-ignition engine to compete very favorably with other types of prime movers in many fields and have led to predictions of fur- ther rapid expansion in the application of Diesel power. In a survey of the field of all petroleum fuels for combustion engines, Holaday et al (9) have predicted that by 1948 railroads will be using 10 times as much Diesel fuel as was used in 1939 and that over-all consumption will have doubled that of 1939. Other estimates of the yearly demand for Diesel fuels five years hence vary from 2,6 to 5 times the amount used in 1944. Into this picture has come the question of whether the greatly in- creased production to meet this estimated demand is compatible with the maintenance and possible improvement in quality of fuels necessary to satisfy future engines. Unfortunately perhaps for the Diesel engine, factors other than those of simple arithmetical multiplication must be considered. For example, the consumption of oil in central heating plants doubled from 1935 to 1943, and a further increase of 57 percent of the 1943 demand is expected by 1950. Jet propulsion has been developed to the stage where it is entirely practical for military aircraft. Catalytic cracking plants, many of which were constructed to meet the war- time accelerated demand for high-octane gasoline, are taking their place in the refining industry. All these developments, as well as the Diesel engine, require material of approximately the same boiling range. Virgin gas oils make excellent burner fuels, perform most satisfactorily in the gas-turbine units for aircraft according to present information, and are at a premium as catalytic cracking stock.

Jul 1, 1948

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

By Lichao Ding, Jingbiao Fan, Yunnen Chen

"With the development of industrial production, more and more wastewater containing high concentration ammonia nitrogen was discharge into the environmemt, which caused serious harm to the environmemt. Treating the wastewater has great significance to protect water resources. Using air-stripping combined with oxidation to uptake high concentration of ammonia nitrogen wastewater. The influence of operating parameters was investigated. Experimental results revealed that pH of solution, aeration time and aeration strength showed heavy influence on ammonia nitrogen removal. Air-stripping combined with oxidation can be considered as an alternative approach for the removal of high concentration of ammonia nitrogen from practical metallurgical wastewater. When pH was 11, aeration time 20 min, aeration strength 1040 Lh-1, and oxidation with 10 % NaClO solution 10 min, the initial ammonia nitrogen 2130 mgr1 could reduce to 12 mgr1. Other items could also be removed to meet the ""Integrated wastewater discharge standard (GB8978-88)"".1. IntroductionThe rapid development of human activities has caused a worldwide increase of nitrogen in rivers, lakes and coastal waters. It leads to considerable eutrophication and an increase in the frequency of toxic algae blooms [1,2]. The concentrations of nitrogen in the water of China are pervading high [3]. The discharge of wastewater containing high concentration of ammonia nitrogen is one of the most important factors. Great efforts have been devoted to the removal of ammonia nitrogen from wastewater. Traditional methods include biological denitrication [ 4 ], chemical precipitation with magnesium ammonium phosphate [5], electrochemical conversion [6], air-stripping [7] and so on. Biological denitrication is the most common process in the treatment of ammonia nitrogen wastewater. But the process is only suitable for the removal of relatively low ammonia concentration due to the requirement of appropriate C/N ratio [8]. Chemical precipitation needs additional reagents, which may introduce new pollutants to water body. Electrochemical method often uses expensive metal or metal oxide as electrodes, and also consumes large quantity of energy [6].Although air-stripping makes use of stripping tower and consumes energy, it is very suitable for the removal of relatively high ammonia concentration. Different air-stripping conditions would appear different removal efficiency. And only air-stripping the effluent can not be attained the ""Integrated wastewater discharge standard (GB8978-88)"". In this study, we use air-stripping and oxidation to removal high concentration of ammonia nitrogen from simulated and real ammonia nitrogen wastewater."

Jan 1, 2011