Search Documents

By Afonso Garcez de Azevedo, Anna Carolina Lopes Rabello, Renan Tavares Vicente, Sergio Neves Monteiro, Amanda Maia Ferreira dos Santos

Civil construction is a sector of extreme impact in the Brazilian economy, with construction and demolition waste (RCD) having an extreme impact on the amount of urban solid waste. In this research it was proposed to propose a way of using these residues in the construction of concrete artifacts for structural use. Concrete specimens with sand substitution by RCD were produced in different percentages as a way to contribute to reduce,recycle and reuse thi large amount of waste from the construction industry. The objective of this work was to study the mechanical properties of structural concrete with total and partial replacement (25, 50, 75 and 100%) in sand mass. The results of the compression test indicate good quality for concretes with mass substitution of up to 75% per RCD.

Mar 1, 2018

By R. O. Dannenberg

Exploratory research was conducted to ascertain the feasibility of recovering beryllium from Spor Mountain, Utah, ore by the sodium fluosilicate (Na2SiF6) method used industrially for processing beryl. Na2SiF6 requirements to form water-soluble salts of beryllium were determined for three different samples--two clayey ores containing 0.6 and 1.3 pct BeO, respectively, and a calcareous ore containing 0.6 pct BeO. The ores were sintered with Na2SiF6 at 750° C for 3 hours. About 80 pct of the beryllium was rendered water soluble by sintering the 0.6-pct BeO ores with 30 and 40 lb Na2SiF6 per lb BeO contained in clayey and calcareous ores, respectively. The higher grade 1.3-pct BeO clayey ore required only 20 lb Na2SiF6 per lb BeO to solubilize over 80 pet of the beryllium. As the 0.6-pct BeO clayey ore was possibly the most representative of the deposit as presently delineated, leach liquor prepared from this sample was treated to recover beryllium salts. About 60 pet of the beryllium contained in the ore was recovered as beryllium hydroxide, which then was calcined to yield a 99-pct BeO final product by means of the following operations: (1) Sintering with Na2SiF2, (2) leaching with water, (3) precipitating crude Be(OH)2 by adding NaOH, (4) filtering to separate the hydroxide from the NaF solution, (5) redissolving the crude Be(OH)2 in excess NaOH, (6) filtering to reject caustic-insoluble impurities, and finally (7) boiling the Na2BeO2 filtrate from (8) to precipitate pure Be(OH)2. Reagent consumption was 49 lb Na2SiF6 per lb BeO recovered and 17 lb NaOH per lb BeO.

Jan 1, 1963

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988

By David B. Brooks, William A. Wallace, James R. Dunn

As the conflict between the mineral industry and preservationists steadily increases, it becomes urgent to determine as precisely as possible the costs of developing vs. not developing our domestic mineral resources so that enlightened mineral policy decisions can be made. A simple discounted cash flow equation is suggested as an approach to assigning a public-interest dollar value to mineral resources. Present value of a piece of land underlain by a mineral resource is taken as equal to the discounted cash flow derived from the resource corrected for present and future surface land values. The equation is effective as a base for mineral aggregate resource planning for metropolitan areas if transportation cost differences are substituted into the cash flow component. Suitably modified, the equation can be fitted readily into an existing computer simulation program for aggregate mineral resource planning in metropolitan areas. However, because of the lack of accurate input, the equation is less effective for other mineral commodities such as base metals and coal. Nevertheless, within a somewhat philosophical context, the equation still has utility and is effective in defining the problem of public interest values for minerals other than mineral aggregates.

Jan 1, 1972

By S. K. Chan, C. Badeen, S. Goldthorp, H. Feng, I. Alilovic, R. Turcotte

Over the last few decades, water-based explosives and their precursors, despite their apparent insensitivity, have been involved in a number of accidents around the world. A large proportion of these accidents occurred when these emulsions were pumped either for their manufacture, transport, or handling. In Canada, this has led to the development of “Guidelines for the Pumping of Water-Based Explosive”, which state that “using pumping pressures well below the laboratory measured minimum burning pressure (MBP) of the corresponding emulsions or watergels is a good safety practice”. However, in the above document, there is no description on how the MBP should be measured. In the last few years, a research program at the Canadian Explosives Research Laboratory (CERL) in collaboration with Orica has been focused on the development of a validated measurement protocol for realistic MBP measurements.

Jan 1, 2014

By Byron R. Berger

Disseminated Au-As-Hg mineralization is localized along the Getchell Fault system at the Getchell Mine in north-central Nevada. Replacement ore bodies occur in Cambrian carbonaceous limestone and limy shale beds. Cretaceous granodiorite, dacite porphyry, and andesite porphyry dikes parallel the fault zone and are spatially associated with the mineralization. Hydrothermal alteration and mineralization occur continuously along 4-5 km of the fault system, and extend more than 1 km down-dip. Alteration consists primarily of removal of carbonate and deposition of quartz, pyrite, and carbonaceous material. Marcasite, sericite, kaolinite, calcite, barite, and fluorite are common. Gold content reaches more than 43 ppm in parts of the altered zones and averaged 9.3 ppm in the mined ore bodies. For the mineralized zones as a whole arsenic averages 0.28%, and occurs primarily as realgar, orpiment, and arsenopyrite. Mercury (22 ppm) is finely disseminated and mercury-bearing minerals are seldom recognizeable. Accessory mineralization includes antimony (100 ppm), copper (47 ppm) , lead (18 ppm) , molybdenum (10 ppm) , tungsten (16 ppm) , and zinc (50 ppm) . Geologic field studies and K-Ar dating suggest that the mineralization is related to a hydrothermal system produced by the granodiorite and related dikes.

Jan 1, 1975

By Cripps-Clark CJ, Deague TK

In order to study conditions under which SiO(g) may be formed in a blast furnace, equilibrium phase diagrams were constructed for the combustion of high and low ash cokes with oxygen-enriched blast and oil injection under conditions of high and low raceway pressures. Free energy minimisation techniques were used to calculate the composition of gaseous and condensed phases. Where coke ash is assumed, for simplicity, to comprise Si02 only, the coke can be comple- tely gasified, mainly to SiO and CO, under restricted conditions of coke to blast ratio and at temperatures greater than 1600 - 1650¦C, depending on system pressure. The formation of SiO(g) is partially suppressed by the introduction of alumina into the ash, because of the formation of solid and liquid alumino- silicate compounds. The minimum temperature for complete silicon gasification is raised to about 1700¦C. The results of the equilibrium calcula- tions are related-to actual raceway conditions. It is proposed that virtually all silicon in the coke ash is gasified such that, on condensation, it affects hot metal chemistry and slag properties and secondly, that the effects will be greater with higher ash cokes.

Jan 1, 1980

By J. E. Hilliard, J. W. Cahn

In this paper it is suggested that the degree of contiguity (or contact) between adjacent grains be described by three parameters which can be rigorously determined from measurements on a random plane of polish. An expression is also derived for the number of contacts per unit volume and it is shown that this quantity can-not, in general, be estintated from measurements on a random plane. IN a recent contribution1 Gurland has proposed various parameters for describing the degree of contiguity (or contact) between grains of the same phase in an alloy. To relate these parameters to measurements on a random two-dimensional section, it was necessary in most cases to make some assumption about the form of the structure. Since Gurland was specifically interested in sintered carbide structures, he chose, quite reasonably, to assume that the grains were constant-size spheres and that all the intersections were flat areas of constant radius. Since, as we will show, the relationships between the parameters and the measurements are strongly dependent on the grain shape and size distribution, it is evident that these assump tions will not be satisfactory approximations for a

Jan 1, 1960

By Lawrence Bbosa, Aubrey Mainza, Indresan Govender

"Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to develop a probability based model for the power draw of a tumbling mill. Experiments are conducted using dry spherical glass bead charge in a laboratory scale tumbling mill, which is mounted with a torque transducer and tachometer to measure mill power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For both sets of data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. The information from both techniques is then used to develop a model for the power draw as a function of particle size, mill speed and volumetric filling. Predictions of the model match well with measured and calculated values. The model is found to predict mill power within close agreement with measurement and follows trends consistent with existing work on tumbling mill modelling."

Jan 1, 2014

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By William Petruk

The capabilities of SEM/image analyzers for determining quantitative mineral data which have a bearing on extractive metallurgy have given applied mineralogy a new dimension. The capabilities include automatic mineral identification, unattended operation, search for rare minerals, and measurements of (1) mineral quantities, (2) grain and particle size distributions, (3) liberation characteristics of minerals in ground ores, and (4) mineral associations. Data on mineral quantities define the distributions of elements among minerals, provide background information on characteristics of the samples, and provide a data base for a mineral-materials balance. Size analysis data of the minerals in unbroken ores are used to predict the grind required to liberate minerals. Data on liberation analysis can be used in many ways. One application is to process the image analysis data for feed, concentrate and tails by a materials balancing technique to calculate the recovery of liberated and unliberated grains at each point in a circuit. The calculated recovery data define the behaviour of an ore in a concentrator, pilot plant or bench test, and indicate whether recovery improvements are possible and/or feasible for a particular ore.

Jan 1, 1991

By E. Bauer

During 1987 and 1988, the Eighty Four Complex Mine of BethEnergy Mines, Inc. used the open entry longwall recovery method to recover one partial and three complete longwall faces. Various cement- concrete supports were utilized to support the open recovery entry until the approaching longwall face cut into this entry. This recovery method and the supports used were studied by the mine personnel and the Bureau of Mines. This paper discusses the findings, results and conclusions of that study.

Jan 1, 1988

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023

By W. B. Lambert

A common decision in openpit mining is to determine the extraction sequence of notional three-dimensional production blocks so as to maximize the net present value of the extracted orebody, while adhering to precedence and operational resource constraints. This openpit block sequencing (OPBS) problem is commonly formulated as an integer program, with binary variables representing if and when each block is extracted. In practical applications, the number of blocks can be large and the time horizon can be long; therefore, instances of this problem can be difficult to solve using the exact approach of optimization. The problem is even more challenging to solve when it includes explicit minimum operational resource constraints. Our maximum value feasible pit (MVFP) algorithm generates an initial integer feasible solution for OPBS problems, in which minimum operational resource constraints are strictly enforced. As an exact approach, we present a Tailored Lagrangian Relaxation (TLR), in which the selection of constraints to dualize is guided by information provided by the MVFP algorithm. We present results and graphics to demonstrate the utility of our techniques for instances containing up to 25,000 blocks and 10 time periods.

Jan 1, 2013

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

By Leah Penner, Thomas J. Ruth, Paul Schaffer, François Benard, Edouard Asselin, Stefan K. Zeisler, Thomas J. Morley

"This paper details the electrodeposition of metallic molybdenum from an aqueous, acetateelectrolyte containing molybdate ions. The deposition is carried out in a highly concentrated (up to I 0 M) acetate bath in the presence of a very low concentration of bone glue (60 µg/L). The molybdenum metal deposits are up to 20 µm thick and adherent. The deposits were characterized by XRD and XPS analysis. The deposition process is very inefficient, as up to 99% of the current is used to generate hydrogen during electrolysis. The effect of acetate concentration, pH, additives and current on the deposition efficiency and physical properties of the molybdenum deposit were investigated and optimized to obtain smooth, adherent coatings.IntroductionMolybdenum has increased thermal and wear resistance properties that are often utilized in material coatings [I]. These coatings are most often manufactured by sintering, pressing or spraying molybdenum powder at elevated temperatures, as a substitute method for standard metallurgical practices, such as electroplating [2, 3]. The lack of reports describing molybdenum deposition is most likely due to the highly oxophilic nature of molybdenum and the stability of its oxides, especially in water. Previous attempts to electrochemically reduce molybdenum from molybdate (Mool·) ions to molybdenum metal have reported the production of either a poorly adherent mixed oxide [4-6], or a thin(< 0.1 µm) metallic film [7-9]. Thick metallic molybdenum is capable of being co-deposited with one of the iron-group metals (Ni [10], Co [11] and Fe [12]) to produce an alloy [13, 14]. These alloys, however, may not be suitable for applications requiring pure molybdenum as they usually contain less than 50% molybdenum (often less than 30%)."

Jan 1, 2012

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996