Search Documents

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By Evgueni Jak

Recent advances in analytical, experimental techniques, and computer-based theoretical modelling of fundamental properties and elemental processes, provide new opportunities to develop the next level of whole-of-reactor pyrometallurgical furnace models. These models have the potential to significantly improve the prediction of, and adding value to, industrial operations. In non-ferrous smelting, the starting point of these models is the development of multicomponent thermodynamic databases for gas-slag-matte-speiss-metal-solids phases supported by systematic experimental research. The whole-of-reactor-models additionally should take into account kinetic processes taking place at micro- and macro- scales, and other key factors. Examples of applications of the latest research tools and modelling approaches to analysis of industrial flash and top submerged lance (TSL) sulphide smelting processes are presented. Different levels of industrial modelling are discussed from elemental local reactions, through general and more detailed whole-of-reactor-models, to plant sections and further to whole plant operation models. Some principles for development of pyrometallurgical reactor models are discussed.

By D. C. Sisti

A technical evaluation of actual performance of the preparation facilities at Beaver Consolidated Coal Co.'s Stinson plant is presented, with special emphasis on sulfur reduction in 1-1/2 x 3/8 in., 3/8 in. x 28 mesh, and 28 mesh x 0 size fractions. Evaluation of the heavy medium section of the plant and the treatment of the 28 mesh x 0 coal is included. Design criteria considered for sizing and selection of equipment required to process 1-3/4 million tpy of raw coal on coals of divergent washability characteristics are summarized.

Jan 1, 1976

By G. H. Lind

This paper discusses the traditional costing approach currently used in the underground coal mining industry. Activity Based Costing (ABC) is identified as being a potentially more effective manner in which to cost underground coal mining systems. With the use of a costing framework developed by the author incorporating new thinking to eliminate the shortcomings identified in the traditional costing approach, a comparison of two types of underground coal mining systems, viz. continuous miner and longwall, is conducted. It is found that under certain criteria, in all cases, irrespective of the way in which the systems are costed, the continuous miner system is currently the better investment. It is also observed that when a system is costed using ABC that better investment decisions result when compared to costing the same system using traditional costing techniques. It is further seen that traditional costing techniques tend to overestimate the total costs of a mining system. This paper shows one application of ABC that can be incorporated as a management tool.

Jan 1, 2001

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated field program over a 37-month period (April 1978 - May 1981). This project was part of a much larger study to determine the economic feasibility of expanding the open-pit, mine-mill operation 10-fold to 80 kt/d (88,000 stpd). The resource project included more than 120 km (74 miles) of core drilling and 64 km (40 miles) of drill rig access way construction under adverse topographic and climatic conditions, detailed geological mapping, and other related activities. The Los Bronces deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. The mineralization is hosted by intrusive and extrusive igneous rocks. Various stages of erosion, oxidation, leaching, and supergene enrichment of copper are present. Drill hole indicated geologic reserves are estimated at 1.3 Gt (1.4 billion st), averaging 0.81% copper and 0.016% molybdenum at a cutoff grade of 0.6% copper equivalence decreasing to 0.25% over the life of the mine. Trace amounts of silver are also present.

Jan 1, 1987

By M. Saghaeian, R. Hejazi, H. Abedini

Vertical ring and Pulsating Wet High Intensity Magnetic Separator (VP-WHIMS) is widely used for week magnetic mineral beneficiation or ferrous impurity removal from non-metallic minerals. Because of the complexity of this machine, mathematical modelling of its process is complicated and time consuming. In this paper, artificial neural network (ANN) and response surface methodology (RSM) were applied to evaluate the VP-WHIMS performance and optimize its main operating parameters in beneficiating of the Chadormalu hematite sample. The operational parameters of this magnetic separator are considered as: magnetic field intensity (2500-8500 gauss), pulsating frequency (20-100 %max), ring rotation speed (0.6-4.6 r/min) and slurry concentration (15-35 w/w %). Concentrate grade and recoveries (weight and Fe) are monitored as responses. Centre composite design (CCD) was used for experimental study. Four process variables were set using small CCD. Eight star points (a=±1), eight axial points (a=±2) and five replicates at the centre point (a=0) were chosen as experimental points. In ANN system, the best network topology was obtained as (4-5-3). The weights connection and biases were obtained using batch back propagation (BBP) method for 21 experimental data points. The results indicate that ANN

Jan 1, 2014

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

A Kellogg type computer model of the slag fuming process is applied in reverse to derive some thermodynamic properties of components in lead blast furnace slag. At 1200¦C, the average activity coefficients calculated were 3.40 (S.D. 0.50) for ZnO referred to the pure solid; 0.657 (S.D. 0.022) for PbO referred to the pure liquid; for the ratios y 3.175 y (referred to the Feo.9450, Fe304 pure solids) 4.19 (S.D. 1.15), and for yCaS/ 1CaO (referred to the pure solids) 5.10 (S.D. 2.96). Statistical relationships were derived for these activity coefficients and ratios as functions of the composition of slag, which contained in molar percentages 1.9 - 12.6% ZnO, 19.8 - 24.9% Fe0.9450, 0.9 - 1.6% Fe304, 0.002 - 1.9% PbO, 16.1 - 18.6% CaO, 25.9 - 31.0% SiO2, 4.8 - 5.5% MnO, 9.2 - 10.3% A101.5, 1.2 - 1.4% CaS, and 5.1 - 9.6% "Mgo" (the balance).

Jan 1, 1980

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By Oliver Bowles

AUTOMOTIVE TRANSPORT by highway, which has become indispensable to modern life either in peace or war, involves the use of powerful machines, many of which travel at high speed. To start, accelerate, and stop each motor vehicle demands the use of clutch and brake. Friction is applied intensively to both these mechanisms, and their linings must therefore be of materials that will resist wear and that will not ignite with the heat of friction. Asbestos, that curious fire-resisting: natural fiber that may be woven into unburnable cloth, is eminently suitable for this special' use, and no satisfactory substitute for it has yet been found Because- asbestos is regarded as absolutely essential to all types of motor transport on land, and in addition is indispensable to. many .other kinds of machines and equipment, the situation of the- United State's with respect to supplies of-raw-material-is of special interest: From the standpoint of national self-sufficiency, conditions are far, from satisfactory, for United States mines furnish only three to four percent of the total domestic require-

Jan 1, 1938

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

The use of mining by-products for beneficial use may face approval, and acceptance barriers. This paper described the use of a sustainability framework to assess the safety, effectiveness and economic value of modified bauxite residue (Alkaloam«) for use on agricultural land in the Peel-Harvey region of Western Australia. The results indicate the merit associated with using this by-product from a safety and, private, community and environmental value perspective. They may be used to indicate the worth of pursuing any future community acceptance and agency approval process.   The use of Alkaloam« for beneficial use on agricultural land in Western Australia was first investigated over 25 years ago. Efforts to gain regulatory approval and community acceptance of Alkaloam« have had a complicated and enduring history. Understanding and assessing the value of a by-product using social and economic considerations, in conjunction with an environmental assessment, provided a more complete evaluation to that previously used.

Jun 1, 2010

By Siemag Transplan GmbH

At the Hansa Mine in Dortmund, Germany, coarse run-of-mine coal, up to 60 mm in particle size, has been brought to the surface hydraulically from a depth of 850 m since November 1977. Hoisting is done by a three-chamber pipefeeder, by means of which up to 400 t/h can be lifted. The pipefeeder operates without problems, and has so far shown itself to be efficient and reliable. Vertical hoisting can be carried out by water supplied from the surface, from underground, or from a surface water supply in combination with minewater from underground. Water that flows into the mine, which would in any event have to be pumped to the surface, can be utilized for hoisting operations. The energy costs per ton of coal for a lifting height of 850 m vary between 41 and 62 South African cents, and therefore lie within the range of costs that apply to conventional hoisting.

Jan 1, 1980

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983