Search Documents

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,' the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

THE Mining Methods Committee during the past year has spent much of its time developing the interest of members of the Institute in the work that comes under its direction. The response on the part of the membership has been most encouraging and in order to give a concrete form to the program which it hopes to develop, an "Outline for Papers on Mining Methods" has been drawn up and is herewith submitted for consideration. This outline has slowly taken shape until it now represents ideas contributed by a great many men, and it is hoped that it will be suggestive and helpful in the preparation of papers. This program can be used for the preparation of papers covering single large operations or, preferably, as the basis for a description of methods and the presentation of results obtained either in different districts or in different branches of the industry. The Committee presents this outline for the consideration of the various Sections of the Institute with the request that they will endeavor to interest the members of the Sections in covering comprehensively the mining operations with which they are connected. It is not the plan of the Committee to publish a paper on every mine, giving all the details outlined, but rather that an engineer familiar with a district prepare the general information and engineers of each important mine in the district compile the specific information of the mine with which they are connected. The general information and the specific information shall be sent to the Committee, and with this information the Committee will prepare a paper on the results obtained under the various mining methods in the different districts. The Committee requests that all papers shall be compiled under the direction of the Chief Engineer of the company and then submitted to the General Manager before acceptance for publication or compilation and tabulation with other similar data. Where the study of this subject approaches the fields of other standing committees of the Institute, the

Jan 5, 1922

By R. V. Mrazek, F. E. Block, S. B. Knapp

The mixed homogeneous and heterogeneous kinetics of the thermal decomposition of tungsten hexacarbonyl were studied by employing a batch reactor. The system was such that a sample of tungsten hexacarbonyl could be injected into the preheated reactor, and the progress of the reaction followed by a simple pressure measurement. Both the homogeneous and heterogeneous reactions were found to be first order, and approximate activation energies were determined for each reaction. It is shown that the dis-proportionation of carbon monoxide to give carbon and carbon dioxide cannot be the source of carbon in tungsten deposits prepared by this reaction. The kinetics of the thermal decomposition of tungsten hexacarbonyl have been investigated as part of a continuing study by the U.S. Bureau of Mines on the decomposition of organometallic compounds. Reactions involving the thermal decomposition of metal carbonyls have a potential application in the preparation of pure metals and fine metal powders. Indeed, it was these applications which provided the impetus for much of the early work involving the carbonyls of nickel1 and iron.' The relative lack of study of other metal carbonyls can be traced to the comparative difficulty in synthesizing these compounds. The most common use for tungsten hexacarbonyl has been as an intermediate in vapor-phase plating.7'8 However, attempts to obtain a carbon-free deposit of tungsten by this method have not been successful, and some investigators have taken advantage of the carbon contamination and used this process to form tungsten carbide deposits.lo Other investigators have studied the thermodynamic properties11"14 and molecular structure of tungsten hexacarbonyl. However, very little is known about the kinetics of this thermal decomposition, the mechanisms involved," or the source of carbon in the resulting plate. In contrast, studies have been made of the kinetics of the thermal decomposition of nickel tetracarbonyl, iron pentacarbonyl, and molybdenum hexacarbonyl.'l It has been found that these thermal decompositions occur by a mechanism which is partially heterogeneous in nature. Information available on the equilibrium constants for the decomposition of tungsten hexacarbonyl was used to determine a temperature range, 500" to 560°K, in which the reaction could be expected to be essentially complete. APPARATUS The apparatus used allowed the injection of a sample of tungsten hexacarbonyl into a preheated batch reactor and the use of a simple pressure measurement to follow the progress of the reaction in the sealed reactor. The pressure was sensed by means of a pressure transducer (Consolidated Electrodynamics Corp., 0.3 pct)* capable of operating at the *Reference to specific products is made to facilitate understanding and does not imply endorsement of such brands by the Bureau of Mines._______ reaction temperature. This type of sensing element was chosen to avoid the problem of condensation of the sublimed carbonyl in the capillary tubing leading to any type of remote pressure-sensing device. stirring was provided by rotating the entire apparatus. Glass beads placed in the reactor provided a pulsating agitation. To minimize thermal gradients in the reactor walls, the reactor was constructed of aluminum. The support tube which held the reactor in the furnace was thin-walled stainless steel to minimize heat conduction out of the reactor. As a result of these measures, a nearly uniform temperature (°C) was maintained throughout the reactor. Fig. 1 is a schematic diagram of the apparatus. The small gear motor rotated the entire apparatus at about 200 rpm. The bearings shown at the ends of the air cylinder were perforated to allow air to be fed to the charging piston and to allow inert gas to be fed to the reactor during the preheating period. The sample was simultaneously injected and sealed inside the reactor by operation of the air piston. Fig. 2 shows a cross section of the air cylinder and the adjoining portion of the support tube leading to the reactor. The sample carrier is shown in place at the right-hand end of the injection rod extending from the air piston. The piston is shown in the retracted position, as it would be prior to the start of an experiment. The small Teflon gasket which encircled the sample carrier at the end of the injection rod sealed the reactor when the sample was injected. This seal was maintained throughout the test by maintaining air pressure on the piston. The sample carrier was a 2-in. section of thin-walled, -in.-diam nickel tubing with an internal blank about 1 in. from the base and with the base end sealed.

Jan 1, 1969

By D. Havlena, A. S. Odeh

The material balance equation used by reservoir engineers is arranged algebraically, resulting in an equation of a straight line. The straight line method of analysis imposes an additional necessary condition that a successful solution of the material balance equatiott should meet. In addition, this algebraic arrangement attaches a dynamic ineuning to the otherwise static material balance equation. The straight line method requires the plotting of one variable group vs mother variable group. The sequence of the plotted points as well as the general shape of the resulting plot is of utmost importance. Therefore, one cannot progrm the method entirely on a digital computer ar is usually done in the routine solution of the material balance equation. If this method is applied, then plotting and anaIysis are asential. Only the appropriate equations and the method of analysis and interpremtion with comments and discussion are presented in this paper. Illustrative field examples for the various cases treated are deferred to a subsequent writing. INTRODUCTION One of the fundamental principles utilized in engineering work is the law of conservation of matter. The application of this principle to hydrocarbon reservoirs for the purpose of quantitative deductions and prediction is termed "the material balance method of reservoir analysis". While the construction of the material balance equation (MBE) and the computations that go with its application are not difficult tasks, the criteria that a successful solution of the MBE should fulfill have always been a problem facing the reservoir engineer. True and complete criteria should embody necessary and dcient conditions. The criteria which the reservoir engineer uses possess a few necessary but no sufficient conditions. Because of this, the answers obtained from the MBB are always open to question. However, the degree of their acceptability should increase with the increase in the number of the necessary conditions that they should satisfy. Generally, the necessary conditions commonly used are (1) an unspecified consistency of the results and (2) the agreement between the MBE results and those determined volumetrically. This second criterion is usually overemphasized. Actually, the volumetrically determined results are based on geological and petrophysical data of unknown accuracy. In addition, the oil-in-place obtained by the MBE is that oil which contributes to the pressure-production history,' while the volumetrically calculated oil-in-place refers to the total oil, part of which may not contribute to said history. Because of this difference, the disagreement between the two answers might be of paramount importance, and the concordance between them should not be overemphasized as the measure of correctness of either one. In this paper, a third necessary condition of mathematical as well as physical significance is discussed. It is not subject to any geological or petrophysical interpretation, and as such, it is probably the most important necessary condition. It consists essentially of rearranging the MBE to result in an equation of a straight line. This straight line method of the MBE solution has invalidated a few long time accepted concepts. For instance, it has always been advocated that if a water drive exists, but one neglects to take it into account in the MBE, the calculated oil-in-place should increase with time. The straight line method shows that in some cases, depending on the size of the neglected aquifer, the calculated oil-in-place might decrease with time. The straight line method requires the plotting of a variable group vs another variable group, with the variable group selection depending on the mechanism of production under which the reservoir is producing. The most important aspect of this method of solution is that it attaches a significance to the sequence of the plotted points, the direction in which they plot, and to the shape of the resulting plot. Thus, a dynamic meaning has been introduced into the picture in arriving at the final answer. Since the emphasis of this method is placed on the interpretation of the sequence of the points and the shape of the plot, one cannot completely automate the whole sequence to obtain "the best value" as normally done in the routine application of the MBE. If one uses the straight line method, then plotting and analysis are musts. The straight line method was first recognized by van Everdingen, et al,2 but for some reason it was never fully exploited. The advantages and the elegance of this method can be more appreciated after a few cases are carefully treated and worked out by it. SOLUTION OF THE MATERIAL BALANCE EQUATION SATURATED RESERVOIRS The MBE for saturated reservoirs written in AIME symbols is

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By C. E. Fivaz

SYNOPSIS Tribute is paid to J.S. MacArthur and the Forrest brothers for their invention. The opinion is expressed that the successful application of their process, not only saved the gold-mining industry on the Witwatersrand from stag¬nation for an indefinite but probably prolonged period, but also made a major contribution to the economic growth of the country in the twentieth century. A background is given of the activities of prominent chemists who researched the solubility of gold in cyanide solution prior to the MacArthur-Forrest invention. An account is given of the invention and patenting of the cyanidation process, and of the golden rule that the patentees laid down for themselves, which came close to wrecking the invention. The South African gold-mining scene from the discovery of gold on the Witwatersrand in 1886 up to 1890 is sketched. An account is given of how, when unoxidized ores were first encountered, the recovery efficiency dropped alarmingly, gold shares were sold on an unprecedented scale, and doom and despondency seized the town of Johannesburg. The complete turnabout in the fortunes of the South African gold-mining industry after the introduction of the cyanidation process in 1890, the steady rate of increase in production after the Anglo-Boer War, and its effect on the South African economy are described. A brief look is taken at the effect of gold mining on secondary industry. The deportment of the gold that is not dissolved from the ore by the cyanidation process is illustrated. Some thoughts are expressed on what can be done to increase the gold recovered by cyanidation.

Jan 1, 1988

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By R. E. Schilson, F. H. Poettmann

The direct determination of the stabilized performance behavior of low capacity, slowly stabilizing gas wells is extremely time-consuming and wasteful of gas. From both field experience and theoretical considerations, a test procedure has been evolved by which the stabilized hack pressure behavior of such gas wells can he predicted without having to revert to long time flow tests. The method consists of using the isochrona1 test procedure to establish the slope of the back pressure curve, "n", and the short time variation of the performance coeficient, "C", with time. From this short time transient flow data and theoretical considerations, the value of C at large times can he established. By assuming the radius of drainage of a well to be half the distance between wells, one can calculate the stabilization time for various well spacing patterns. Once the stabilization time for a given .spacing has been determined, the value of C can be calculated and the stabilized back-pressure curve can he. establbrhed. The calculated perfortnance coefficient as a function of tinze was cotnpared to the experintentally measured values for a number of gas wel1.e. The deviation of the calc~*lated from the cxperimental res1tlt.s vary depending on the set of short time experimental points used to evabrate the parcrttzeters of the equation. The longer the tirne far the flow test data user1 in the calculations, the better was the agreement with the experimental results. The time necessary to obtain this data from well tests varies consitlerably, depending on the physical natrcre oj the rt3scrvoir under consideratiot~. INTRODUCTION For many years, the U. S. Bureau of Mines Monograph 7' has served as a guide for testing and evaluating the performance of gas wells by means of the back-pressure method. The back-pressure performance of a gas well is expressed by the following equation: Q~ CW-W.........(I) where the characteristics of the back-pressure equation are determined by C, the performance coefficient, and n, the exponent which corresponds to the slope of the straight line when Q and {P* - PN2) are plotted on logarithmic paper. Q is gas flow rate at standard conditions, and P, and P, are equalized and flowing bottom-hole pressures, respectively. Prior to the development of the back-pressure tcst, the "open flow" capacity method of testing a well was common. By this method, the wells were flowed wide open to the air and the flow rate measured. Such procedure was wasteful of gas and did not provide information on the deliverability of the gas to the pipe line. Monograph 7 Procedure The back-pressure method of testing wells was developed to overcome these shortcomings. Although much has been learned regarding the laws of the flow of gas through porous formations, the original development of the back-pressure relationship was based entirely on empirical methods. The back-pressure behavior provides the engineer with information essential in predicting the future development of a field. It permits him to calculate the deliverability of gas into a pipe line at predetermined line pressures, to design and analyze gas gathering lines, to determine the spacing and number of wells to he drilled during the development of a field to meet gas purchasers' requirements, and to solve many other technical and economic problems. As described in Monograph 7, the flow-after-flow method of back-pressure testing, when applied to fast stabilizing and usually high capacity wells, correctly characterized the behavior of the well. However, as the value of the gas at the wellhead increased, small capacity gas wells having slow rates of stabilization became economically operable. The flow-after-flow method of testing could not be used to describe the behavior of these slowly stabilizing wells. The procedure of Rawlins and Shellhardtl for establishing the back-pressure behavior of a gas well was based on the rcquirement that the data be obtained under stabilized flow conditions; that is, that C is constant and does not vary with time. C depends on the physical properties of the reservoir, the location, extent and geometry of the drainage radius, and the properties of the flowing fluid. In a highly permeable formation, only a very short period of time is required for the well to reach a stabilized condition, and, consequently, the requirements for the test procedure described in Monograph 7 are met. For a given well, n is also constant

By Matias Suarez, Diego Zenteno

It is known that the introduction of electronic timing in the sequencing of blasting has changed the vision and way in which mining is developed. It is possible to deal with more complex and sophisticated drilling designs, without compromising productivity or safety. It has been shown in various studies, that a correct timing of the blasting provides an improvement in the improvement of the processes downstream, due to a decrease in the resistance of the resulting fragments coming from the interaction of the waves generated in the detonation of explosive loads. On the other hand, it has also been shown that variations in the composition of a same type of explosive, has a significant influence over the resistance of the blasted material, also the energy associated to break it, affecting directly its degree of fragmentation. This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002). This study focused on the methodology of the formation and measurement of seismic pulses, through the rock massif. For this purpose, seismic pulses were acquired in the field and then, the different dynamic phases of the wave were molded mathematically, with the purpose of favoring the coupling between them.

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By L. S. Panyity

THE State of Ohio is among the pioneers in the production of oil and gas. Numerous anticlinals, such as the Macksburg, Cow Run and Newport, have been thoroughly developed, and the pools found in connection with them are quite in accord with the structural theory. Numerous oil and gas pools found in the Berea sand, however, demand a different explanation. The study of these pools belongs to the sub-surface geologist, as it is possible to understand the factors controlling "off-structure" accumulations only after a careful study of well records. By carefully analyzing the various 'conditions over a large territory, it is possible to understand the otherwise meaningless mass of data that one may have at hand, and put it into tangible shape, from which various conclusions may be drawn. The territory here discussed includes Belmont, Guernsey, Muskingum, Noble, Monroe, Morgan, Washington, Athens and Meigs counties, containing the majority of the prolific oil and gas pools of the Carboniferous system in southeastern Ohio. The general dip of the strata is to the southeast, the entire territory lying on the northwestern flank of the Appalachian geosyncline. The best known oil- and gas-producing horizon in the territory is the Berea sand, which lies near the lower part of the Mississippian, with the Sunburry shales (the coffee-shales of the driller) above, and the Bedford shales below it. The Bedford is underlain by the thick Ohio shales. The Ohio and Bedford contact is considered to be the dividing line between the Carboniferous and Devonian systems. The Berea is one of the most persistent of recognizable oil and gas horizons; its outcrop has always been found in its expected place, and it has always been penetrated whenever the drill went deep enough. It is not expected, however, even of the most uniform formations, that no lithological variations should occur, and the Berea is no exception. Nevertheless, there appears to be a certain regularity in its variation, the main features of which directly affect the accumulation of petroleum.

Jan 8, 1918

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By J. W. Halley

RIMMING steels derive their name from their action during solidifica-tion in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop ill the molds, are deter-mined by the Composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accu-rately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring condi-tions and furnace practice on the distribution, though there is still much to be done in this direction.

Jan 1, 1938

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013