Search Documents

By J. W. Cunningham, W. A. Tiller, D. H. Lane

The effect of ultrasonic vibrations on ingot solidification has been considered both theoretically and experimentally. The theoretical section elucidates the mechanisms by which the ultrasonic vibrations might refine the ingot structure. The experimental section describes a very efficient means of introducing the ultrasonic vibrations to the freezing interface. The application of this technique to the consumable-electrode arc melting process shows that the columnar mode of freezing may be effectively suppressed yielding an ingot structure consisting predominantly of equiaxed grains. The results support the contention that the ultrasonic vibrations increase the nucleation frequency in the layer of liquid adjacent to the freezing interface. CERTAIN structural characteristics of as-cast ingots are undesirable since they create considerable difficulty for subsequent processing and often produce defects in the finished product. These structural defects are illustrated in Fig. 1(a), and are: 1) planes of weakness where columnar grains growing from the different mold faces meet, 2) strength anisotropy due to the preferred orientation of the columnar grains and 3) inhomogeneity due to segregation at dendrite boundaries within the columnar grains and at the columnar grain boundaries. The type of ingot structure that eliminates 1) and 2) and diminishes 3) is the fine-grained equiaxed structure illustrated in Fig. 1(c). Many attempts have been made to produce the desirable ingot structure illustrated in Fig. 1(c) by inoculating, casting with varying superheats, vibrating or stirring, or by irradiation with ultrasonic vibrations. These attempts have met with various degrees of success, the ingots generally having the structure illustrated in Fig. 1(b). All four methods have been the subject of numerous investigations,1"4 the latter producing the most erratic behavior and inconsistent success. The method of ultrasonic irradiation during ingot solidification has shown considerable promise on small-scale ingots (diam 2 in.) but has not yet been successfully adapted to large-scale operation. The present paper considers the application of ultrasonic radiation to ingot solidification both theoretically and experimentally. The purpose of the paper is to elucidate the mechanism by which ultrasonic energy refines the ingot structure and to describe a method for producing the desirable ingot structure in both laboratory scale experiments and in ingots of commercial size. THEORY Conventional Casting—Before discussing the possible effects of ultrasonic radiation upon ingot structure let us first briefly review the reasons for the breakdown of columnar crystallization to equiaxed crystallization during ingot solidification. The following is a slightly oversimplified description. In the conventional method of casting, the alloy having a certain degree of superheat, T, is poured to fill a cold mold which is at room temperature, Tc,. Due to conduction of heat through the mold wall the outer rim of liquid metal cools rapidly to the liquidus temperature and begins to supercool. At some degree of supercooling, nuclei of solid form at random in this supercooled layer at the mold surface. The grains in this chill layer begin to grow inwards producing a solute build-up, thus lowering the freezing temperature at the interface as illustrated in Fig. 2. As growth proceeds, the temperature gradient in the solid conducts away not only the latent heat of fusion evolved during growth but it also conducts away some of the superheat of the melt so that the temperature

Jan 1, 1961

By Joseph A. Holmes

The public is already familiar with the general fact that the scope and the financial resources of the approaching St. Louis World's Fair are much larger than those of any of the preceding great expositions; and both the visitor and the exhibitor, when he comes to St. Louis in 1904, will find it to be a real World's Pair, with exhibits and visitors from every known country. Passing over the subject, as to the general Exposition, with this brief statement, I ask Sour attention to the consideration of a few important facts connected with the proposed mining exhibits at this Exposition. First of all, I may say that. reading- and writing-rooms and library facilities will be furnished in the Mines Building for miners and mining engineers, and it is expected that when they visit the Exposition they will make these rooms their headquarters, and give the Chief of the Department and his assistants an opportunity to extend to them such courtesies as may be possible. One of the exhibits in the Mines Department will consist of models and maps arranged to show the nature and extent of the mining operations in the United States at the time of the purchase of the Louisiana Territory in 1803, the event which

Jan 1, 1903

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By M. Turner-Jones, N. Steenekamp

"The Lonmin Base Metal Refinery treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode as well as a concentrate containing the platinum group (PGM) metals. The original process employed a Sherritt design and utilizes atmospheric and pressure leaches for the dissolution of base metals. This paper describes the original flow sheet and the improvements made to enhance PGM recoveries, product quality and to increase capacity. Changes include the introduction of flash recycle cooling on the autoclave, batch leaches to improve the quality of the PGM concentrate and the implementation of solid-liquid separation with centrifuges. INTRODUCTIONThe Lonmin Base Metal Refinery (BMR) is about 100 km north-west of Johannesburg and treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode and a concentrate containing the PGMs. The plant was commissioned in 1985 based on a Sherritt design to treat 12 tonnes converter matte per day. The original flow sheet consists of a milling circuit, an atmospheric leach and a pressure leach to produce a PGM concentrate which is despatched by helicopter to the Lonmin Platinum refinery in Brakpan, about 40 km east of Johannesburg. The liquor from the atmospheric leach is treated by crystallization to produce a nickel sulphate hexa-hydrate crystal. The leach liquor from the pressure leach is treated by a selenium removal step followed by electro-winning to produce copper cathode. The spent solution from the copper electro-winning is recycled to both the atmospheric and pressure leach steps to provide sulphuric acid for the leaching reactions.Modifications were made to the original circuit to increase the plant capacity, to improve the PGM recoveries and to improve the quality of the PGM concentrate. Capacity increases included all the unit operations, new mill, new first stage, additional autoclaves, additional nickel sulphate crystallizers, new copper electro-winning and new batch leach reactors for upgrading the PGM concentrate. The current circuit is described in this paper and not the detailed history of each plant change."

Jan 1, 2012

By K. V. Fedotov, G. I. Sarapulova

The study is devoted to the earth's surface protection and is aimed at improving the ecological safety of the territories in the mining industry. Identification of the diagnostic signs and quantitative criteria for the disturbance of soil geochemical properties and water chemistry represent an important scientific task in anthropogenically disturbed landscapes in the context of comprehensive exploitation of mineral resources. The study is aimed at geological and ecological analysis of the migration peculiarities of the man-caused chemicals and elements in soils and soil-surface water environment. We received new results. These results assist in estimating the peculiar features of distribution of heavy metals total and mobile forms (Cu, Ni, Zn, Pb), depending on the physical and chemical parameters of the disturbed soils. We obtained the empirical relationships describing heavy metals localization and accumulation processes depending on buffer properties of soils (pH, N, Corg), salinization factor and contamination with oil products. Anthropogenic geochemical barriers spontaneously formed in the area of industrial facilities were revealed in the territories of industrial facilities. These barriers prevent the further distribution of elements and pollutants in the landscapes. This makes it possible to create their artificial analogues in order to limit further migration of pollutants and to immobilize valuable components. Analysis of diagnostic features of soils geoecological state and factors influencing the distribution of heavy metals in the soil-surface water geosystem allows the identification of the geochemical barrier type with the aim of elements immobilization in a limited area of the territory. We applied modern physical and chemical methods of analysis, a package of statistics programs in Excel and modeling techniques. The proposed approach is innovative and therefore can be attractive. The accumulation of useful components losses in mineral resources exploitation is a promising reserve for their recovery from the soil with specifically arranged properties. The methodology of this research is also promising for the prediction of the environmental emergencies of the anthropogenic nature. This is consistent with the requirements of state control of environmental safety in the course of comprehensive exploitation of mineral resources.

Jan 1, 2018

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By A. Vifian, I. lwasaki

Several samples of copper-nickel ore from the Duluth Gabbro were studied to relate their mineral-ogical characteristics with their amenability to concentration by flotation. The most common rocks in the samples were norites, gabbros, and troctolites. The texture of the rocks varied from coarse pegma-titic to very fine. The copper contents ranged from 0.2-0.7% and the nickel contents from 0.07-0.15%. The ore minerals were chalcopyrite, cubanite, pyrrhotite, and pentlandite. Most of the ore minerals occurred in interstices between laths of plagioclase, but some were included in the gangue grains. The samples responded readily to xanthate flotation. After a 65 to 100-mesh grind about 95% of the copper and 85% of the nickel were recovered in a bulk sulfide concentrate. Such recoveries remained constant even with grinds as fine as 270 mesh due to the extremely fine inclusions of sulfides in the silicate gangue. A finer grind than 270 mesh was necessary to free the copper-iron sulfides from the nickel-iron sulfides. A combination of time and British gum* was quite effective in producing concentrates analyzing 25-30% copper. The nickel concentrate averaged 1.5% nickel. Most of the nickel lost in the tailing was present as un-liberated sulfides and not as nickel in the olivine structure. The nickel content of the olivine was only about 0.05 or 0.08%. Western world nickel usage in 1967 is expected to be the second highest on record, amounting to 825 million lb. Despite a rise in mine production, however, demand is expected to exceed supply in 1968. ' Hence, exploration, development, and production expansion projects are being accelerated on a world scale. In Minnesota the copper-nickel bearing Duluth Gabbro is receiving much attention. During the past year 11 companies have been granted leases in the region, and the 1967 Minnesota legislature enacted a tax law designed to encourage the development of a copper-nickel industry. Although it is only during the past few years that mining companies have shown an active interest in the Minnesota copper-nickel deposit, copper-nickel minerals have been known to exist in northeastern Minnesota since 1899.3 At the 28th Mining Symposium, Dr. P. K. Sims, from the Geological Survey of Minnesota, gave a review of copper-nickel exploration in northeastern Minnesota,4 in which he emphasized that the potential of the Duluth Gabbro complex is large. Tests on samples from the Kawishiwi River area were reported by the United States Bureau of Mines in 1955.' In 1964, the Mines Experiment Station described tests on samples from the Gunflint Trail: and in 1966 the Minnesota Geological Survey published a geological map of the Gabbro Lake Quadrangle. The Mines Experiment Station published a study of the concentration of a Minnesota copper-nickel ore in 1967.7 The present paper is divided into three parts. The first describes the mineralogy of some rock samples from the Kawishiwi River area of northeastern Minnesota; the second summarizes the results of numerous flotation tests that were made on the samples, and the third explains the loss of nickel in the flotation tailing. MINERALOGY OF KAWlSHlWl ROCKS Recently five samples of mineralized gabbro from the Kawishiwi River area, a few miles east of Ely, were received at the Mines Experiment Station. One of the samples was a 175-lb composite, which was designated Ore 1556. The other four samples were 7-lb grab samples that had been obtained from four different exploration pits. They were designated Ore 1626, Lots 1 through 4. Basic Mineralogy: Many authors have reported that the rocks of the so-called gabbro of the Duluth Intrusion vary widely in composition.8-9 The samples on which our studies were based also contained a wide range of rocks. A gabbro, olivine-gabbro, anorthosite-gabbro, norite, and a troctolite were represented. The essential minerals in the samples were plagio-clase, pyroxene, and olivine, in variable proportions.

Jan 1, 1969

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Hans Chr Andersen

Almost every form of iron ore and carbon material has been used as a raw material in the production of pig iron in electric reduction furnaces. Experience derived from the operation of the large 33,000-kva. Tysland-Hole furnaces, however, indicates that production results are very much influenced by the raw material conditions. The author presents the principle pattern of the metallurgical structure of the interior of an electric pig iron furnace. On the basis of this, he discusses the variations of electrical and metallurgical conditions for the process which will take place with changing raw materials. The formation of a coke bed underneath the electrodes, and its influence on the furnace operation, is illustrated. Quality and grain size of the coke added to the charge will influence the build-up of the coke bed and will thereby also affect the electrical re-''Elektrokemisk A/S, Oslo, Norway. resistance and reduction potential in the furnace.

Jan 1, 1963

By Ionel Gardescu

IN connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,1 an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the dis-placement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S5, R4, the sand reservoir R, R1, R2, F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415 lb. per sq. in. with no free gas present. This was ascertained by. closing off all the outlet valves, and determining the coefficient of compressibility of the system by means of the dis-placement chamber D.

Jan 1, 1932

By William J. Dimond

Computor analysis has opened a new world of information for the mining of resources. This paper is directed at the mining of coal. The same procedures apply to most mining projects. The available facts when evaluated against the variables produce the answers. The project must be carefully analyzed, so that the facts can be organized in a data file. The file can be expanded as additional information is obtained during the entire life of the mine. If the mine is pre-planned, the file will be expanded in an orderly fashion and updated information will be available at all times. The development of a property goes through several phases; Exploration, Economic Analysis, Development, Production, and Reclamation. Each phase is an expansion of the data file. The validity of the answers is directly related to the accuracy and quantity of available data. The basis for a data file is horizontal position, and elevation of each piece of information. A coordinate system and datum are reference for a digital (X, Y and Z) position in a spatial system, a three dimensional digital model of the mine. The current practice is to use the State Plane Coordinate system and elevations as established by the U. S. Coast and Geodetic Survey. Each state has adopted this system by law. In the event there is litigation, it is an advantage to have the data on the legally recognized system. The control must be expanded so that all data can be assigned a digital position, and planned to fulfill the requirements for all phases of the mining operation. The project must be analyzed to insure that the objectives can be achieved without duplication or loss of time. sufficient data must be available to reach each required level of information. The coal data can be defined in two categories, spatial

Jan 1, 1977

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Arthur F. Taggart

The major portion of the work described in this paper was performed by R. W. Young, † a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at east 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation. In

Jan 1, 1918

By E. D. Gardner

"Introduction Ore from stopes in metal mines is generally dumped or drawn into chutes or raises through which it passes by gravity to the haulage levels. Occasionally, and under some conditions quite frequently, the ore in a chute will wedge or hang and refuse to run. This hanging of the ore may be due to the packing of damp or clayey material, to boulders forming an arch, or to loose lagging or other timber becoming lodged in the chute.In drawing material from a loading chute it is drawn out a car at a time, and the intermittent flow of the material .increases its tendency to hang. When the obstruction in the chute is near or at the loading gate, the chute pullers start the ore by punching it with iron bars inserted through openings in the chute gate. When the obstruction is beyond reach of the bars, other means of starting the ore must be used.In some systems of mining, chutes or ore raises are built with timber as the stope extends upward. Generally, a manway is left alongside of the chutes, and when the ore hangs in a chute usually it can be started by a miner from the manway ladder by pounding on the timbers of the chute or by punching the ore with a bar inserted through small holes in the chute lining. Special methods of starting clogged ore, such as shaking a chain left hanging in the chute, are used at some places.In other systems of mining, ore passes or chutes are run through solid rock and when the ore hangs in one of these passes, either it must be blasted or else started from the top. Sometimes the ore can be started by running water into the top of the chute, but if the water does not start the ore moving, it must be blasted from underneath. This is done by detonating a bundle of cartridges under the obstruction in the chute or raise."

Jan 1, 1927

By F. H. Samuel, A. M. Samuel, H. R. Ammar

Casting imperfections, such as porosity, in cast aluminum components greatly influence their fatigue properties. The effect of porosity on the fatigue life of 319-F and A356-T6 aluminum alloys was studied, where the porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The results show that porosity has the most detrimental effect on the fatigue life: 92 % of all tested samples fractured due to porosity acting as the main crack initiation site. In the absence of casting imperfections, other microstructural aspects such as slip bands can be responsible ( 4 % ). The porosity was investigated in terms of the pore size at the sample fracture surface and its location i.e. near the edge or close to the interior. It was found that porosity located far from the sample surface (edge) has less influence on the fatigue crack initiation, and the fatigue life decreases as the size of the pore located at the sample surface increases. Aluminium

Jan 1, 2006

By Etsuro Shibata

The saturated solubility of chromium oxide and the valence of chromium in the slag are important matters when considering how to effectively utilize chromium-containing slags. The experimental data of various types of slags cited in the literature were arranged according to the optical basicity in order to evaluate the effects of the oxygen potential and the slag composition. The saturated solubility of chromium oxide and the Cr2+/ Cr3+ ratio tend to decrease with the increase of the optical basicity of the slag at an oxygen potential below 10.5 atm. However, at an oxygen potential of 0.21 atm, the saturated solubility and the Cr6+/Cr3+ ratio tend to increase with an increase of the optical basicity. A practical approach was suggested to reduce chromium in the stainless steel slag and simultaneously recover it as a ferroalloy by the direct smelting reduction of chromium oxide in the molten slag using some reductant in a small furnace.

Jan 1, 2003

By S Servant

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the stope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the stope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this mine.

Jan 1, 1998

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014