Search Documents

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By Remi Tremblay

This paper describes the laboratory study which permitted an exploration of high grinding ball consumption in the secondary open circuit wet grinding mills at the Sidbec-Normines plant, Port Cartier, Québec. Corrosion undoubtedly exists but is of minor importance. Abrasion resulting from the physical nature of the company's iron concentrate is the main reason for the high ball wear. It was found that at least 30% reduction in ball consumption is possible by decreasing attrition grinding through the use of lifters in the mill. At the industrial level this would entail more lifters and/or higher lifters in the mill linings.

Jan 1, 1984

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery' reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.' They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

By Carl Wagner

AT elevated temperatures. most metals react with oxygen, sulphur, or halogen rather rapidly, although a coherent layer of the reaction product is formed and separates the two reactants from each other. The reaction proceeds, since one of the reactants or both dissolve and diffuse across the reaction product. In many cases the rate is diffusion-controlled as is indicated by the validity of the parabolic rate law of Tammann&apos; and Pilling and Bed-worth. wott and Gurney&apos; have suggested that diffusion processes also play an important part in the case of reduction reactions. This is confirmed by observations reported below. In general, however, the rate of reduction reactions is determined not exclusively by diffusion processes. Reduction of Silver Sulphide Above 179°C silver reacts with liquid sulphur very rapidly. Since the volume of silver sulphide is much greater than that of the equivalent amount of silver, a coherent layer of silver sulphide is formed in accordance with a rule established by Pilling and Bedworth.&apos; According to Wagner&apos;,&apos;&apos; silver ions and electrons migrate from the Ag-Ag,S interface across the silver sulphide layer to the Ag,S-S interface where the following chemical reaction takes place: 2 Ag +2 e + S Ag,S If silver sulphide is reduced by means of hydrogen, the equivalent volume of the reaction product, silver, is less than that of the initial substance. Accordingly, no coherent layer of silver is formed. Instead, fine filaments of silver grow from the silver sulphide surface into the ambient gas. This phenomenon has been investigated by many authors, especially by Kohlschiitter," who has also reviewed previous literature. Kohlschiitter has interpreted the observed phenomena by migration of "silver" dissolved in silver sulphide. According to Wagner,&apos; silver ions and electrons are the migrating particles. The sequence of consecutive steps involved in the reduction of silver sulphide is shown in Fig. 1. Every- where at the silver sulphide surface, hydrogen reacts with sulphur so that excess silver ions and electrons are formed, which migrate at random until they are captured by a nucleus of metallic silver. If such a nucleus lies on the surface and material is furnished only from the base, the original nucleus is pushed outward and thus a filament grows. Removal of sulphur and formation of metallic silver may also take place at different points when silver sulphide is reduced by copper. The reaction is usually formulated as: AgL,S + 2 Cu = Cu.S + 2 Ag but the actual reaction products are silver and a solid solution of the two sulphides. Primarily, excess silver and electrons dissolved in silver sulphide are formed. After a certain degree of supersaturation has been reached, nuclei of metallic silver may form. If, however, a silver foil is in contact with the silver-sulphide phase, as is shown in Fig. 2, silver ions and electrons will migrate to the Ag,S-Ag interface where they are captured. To confirm this scheme, a composite sample, with the geometry shown in Fig. 2, was made by pressing silver sulphide tablets 0.6 cm in diam and 0.4 cm high together with a copper cylinder and a silver foil in crucibles of iron, which does not react appreciably with silver sulphide at 400°C. After heating for 3 to 7 hr at 400°C. the specimens were cut normal to the phase boundaries. It was found that the thickness of the silver foil had increased from 0.01 cm as initial value to a maximum value of 0.06 cm. In the interior of the silver sulphide tablets only traces of metallic silver were observed. These observations show clearly that silver ions and electrons may migrate over distances of several millimeters before they form metallic silver. Reduction of Cuprous Sulphide by Iron The behavior of cuprous sulphide is very similar to that of silver sulphide, since the lattices of the high temperature modifications are identical, but in Cu.S there is a variable deficit rather than an excess of metal. To investigate the displacement of copper by iron, cuprous sulphide powder covered by a copper foil was pressed in iron crucibles and heated up to 800 °C for 3 to 7 hr. The thickness of the copper foil increased from an initial value of 0.005 cm to a nlaximum value of 0.029 cm. In the interior of the

Jan 1, 1953

By P. G. Winchell, A. J. Heckler

An experimentally simple method for determining the effect of alloying elements on the activity of carbon is validated in Fe-Ni-C austenite. The technique consists of the equilibration of carbon between specimens of different nickel contents within a sealed silica capsule. The attainment of carbon equilibrium within each capsule is evidenced by: 1) in each capsule specimens of the same nickel content attained the same final carbon content regardless of their initial carbon contents, 2) in every capsule the final carbon content was reached for most nickel contents by carburizing and by decarburizing. The activity of carbon attained within each capsule was calculated from the carbon content of a binary Fe-C alloy placed within the capsule, and from the activity coefficient of carbon in the Fe-C system as found by Smith for CO/CO2/C equilibrium. The activity of carbon in Fe-Ni-C austenite determined by this method at 1000°C agrees with prior work by Smith, who used mother method. The measurements are extended to 800°and 1200°C. The activity coefficient of carbon 7c, in Fe-Ni-C austenite is given by: where xC is the ratio of carbon to metal atoms and XNi is the ratio of nickel to metal atoms and where the standard state is chosen such that yC = 1 as xc approaches zero in Fe-C alloys. This equation appears to be valid for xni < 0.3, and 1073° < T<1473°K. ThE activity of carbon in Fe-C austenite has been measured by smithL at 800°, 1000°, and 1200°C. Smith has also studied the effect of nickel on the activity A. J, HECKLER and P. G. WINCHELL are Graduate Student and Associate Professor of Metallurgical Engineering, respectively, School of Metallurgical Engineering, Purdue University, Lafayette, Ind. This paper is based on a thesis submitted ty,to Purdue University, in partial fulfillment of the requirements for the degree of M.S. in Metallurgical Engineering which A. J. HECKLER received from Purdue in January 1962. Manuscript submitted August 13, 1962. IMD of carbon in austenite at 1000°C. In both these studies the activity of carbon was fixed by a flowing CO-C02* *Gas mixtures of hydrogen and methane were also used in Ref. 1 but these results are not incorporated in Ref. 2 or in the present study. gas mixture. In the present work, Smith&apos;s results for Fe-Ni-C austenite are confirmed and extended to 800" and 1200°C by a different experimental technique. EXPERIMENTAL PROCEDURE In essence the experimental technique consisted of enclosing specimens of various nickel contents in an initially evacuated silica capsule and annealing the capsule until carbon equilibrium was attained among the enclosed specimens. The carbon activity obtained within the capsule was determined from the final carbon content of the binary Fe-C alloy included in each capsule and the results of smith.&apos; In order to evaluate this method the absence of nickel transfer between specimens must be established and the attainment of carbon equilibrium between samples must be assured. The absence of nickel transfer was demonstrated in the case of an originally pure iron sample which was annealed at 1200°C in a capsule with a 27.3 at. pct Ni alloy. The final nickel content of the iron specimen was less than 0.1 at. pct, a change which has a negligible effect on carbon activity. The attainment of carbon equilibrium was demonstrated within every capsule and in over half the results by achieving the same final carbon content in a sample which carburized during equilibration and in a sample of the same nickel content which decarburized during equilibration. The base Fe-Ni alloys were vacuum melted from Ferrovac E or electrolytic iron and Mond or electrolytic nickel. The samples were rolled and/or swaged and their carbon content adjusted to the desired pre-equilibration level either by methane-hydrogen carburization or by direct carbon transfer from a graphite source in a sealed silica capsule. As mentioned previously, high-carbon and low-carbon samples were prepared for most nickel levels in each capsule. The specimens were cleaned and

Jan 1, 1963

By Harold M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since In most fields gas under pressure is the main source of the energy causing the oil to move throug the sands into the wells and thence to the surface, this coincident production of natural gas will contime as long as present day producing methods are used. Generally the use of this gas is restricted, and markets are not readily available Consequently, a large portion of the gas produced at such times is often wasted by being blown into the air.

Dec 1, 1930

By P. G. Carpenter, R. G. Nisle, F. W. Bubb

It is the purpose of this paper to describe an electrical computer which has been constructed to solve the equations for vapor-liquid equilibrium in multi-component systems. The instrument consists of seven component-computing units each with proper indicating means and power supplies. Each unit is a resistance network with a voltage matching servomechanism, and each provides an output voltage proportional to the mol-fractions for vapor and liquid phases. These voltages are summed and matched with a reference voltage to provide the solutions. Any reasonable number of such units may be put together to make a computer. The theory and operation of the computer is discussed. A number of applications and examples of computer results are given. The computer yields the over-all vapor or liquid fraction to a probable error of 0.002. An interpolation method is described which reduces the probable error to 0.0002. INTRODUCTION The process known as Flash Vaporization may be described as follows: A mixture of known composition of relatively volatile components is allowed to come to thermodynamic equilibrium at some given temperature and pressure by any path whatsoever. In general, a vapor and a liquid phase will be present at equilbrium. The problem is to determine the fractions of the mixture in the vapor and liquid phases, and to determine the mol fractions of the various components in each phase. The relations that exist between these various quantities at equilibrium are well known and will be given later. These equations are difficult to solve, yielding only to trial-and-error methods. The virtues of the analog computer are its speed and the automatic character of its calculations. The device is operated by turning a crank which varies the value of v, the total vapor fraction. This actuates a number of servomechanisms which perform automatically all computations. This computer facilitates the solution of such problems as (to mention a few] : Analysis of separator operation, studies of changes in composition of reservoir fluids with pressure decline, and analysis of natural gasoline plant operation. Examples of some of these problems are given in detail later. STATEMENT OF THE PROBLEM The essential equations are xm = 1+(km-l)v . . (1) Kmzm ym =------------------------. . (2) 1 + (Km-l)v ; n n S S xm= --------------------=1 1 + (Km-l)v m = 1 m=1 ......(3) n n S = S Km Zm =1 S ym 1 + (Km-1)v m=1 m = l ......(4) where ym = Vm/V = Mol fraction of m-th component in vapor phase. xm = Lm/L = Mol fraction of m-th component in liquid phase. Zm = Fm/F = Mol fraction of m-th component in mixture. KM = ym/xm = Equilibrium constant for m-th component at the given temperature and pressure. v = V/F = Mol fraction of vapor in the mixture. F = Total mols of a mixture of n components. V - Total mols of vapor in the mixture. L = Total mols of liquid in the mixture. Fm = Total mols of m-th component. Lm = Mols of m-th component in liquid phase. Vm = Mols of m-th component in vapor phase. Assuming the total mols of the mixture F and its composition (all the Fm) to be known — either from a quantitative analysis or from the amounts put together to make the mixture — the zm = Fm/F may be regarded as known quantities. From the given temperature and pressure of the mixture the K., are known (principally from experimental data). The primary problem is then: having given all the zm and Km to calculate v and all the fractions xm and ym. Having calculated these ratios, it is a simple matter to calculate V. L. Vm, Lm from their defining equations. SOLUTION OF THE PROBLEM Basic Computer Unit The computer consists of n units, each of which provides voltages xEo and YE, proportional to x and y as in

Jan 1, 1950

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors&apos; point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.&apos;-* Author&apos;s Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully&apos;s electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully&apos;s "precipitate1&apos; density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

By Lynce AJ

A method has been developed for the prediction &apos;of &apos;the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b&apos;f the circuit on a digital computer by means of. matheinatical&apos; models ":bf the"&apos; individual units:, the. development of which is- also discussed&apos;., At present, in order to establish &apos;the!&apos;" charac&apos;teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know&apos;the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. &apos; ,Fiiither work on :the- separate identification &apos;of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of deslim-ing, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants. IN the past, mills treating ores of tin and tungsten by gravity concentration have recovered very little mineral finer than 325 mesh, although some form of slime concentration has been generally attempted by the use of buddies or round tables. This paper describes a series of pilot plant tests made in 1942 and 1943 in which the use of the Sullivan deck was investigated for the recovery of an appreciable amount of the fine values formerly lost. The investigation was initiated by the U. S. Government in an effort to increase the wartime production of tin. Bolivian milling practice at that time included jigging of the coarse sizes, tabling of the intermediate sizes on conventional shaking tables, and the use of buddies or round tables on the finest sizes. Flotation of the pyrite was employed at different stages of the treatment, depending upon the quantity present and the preference of the operator. Usually good recoveries and the bulk of the production were made in the jigging and tabling operations provided that these sections were not overloaded. Buddies and round tables were used for a small additional recovery if it could be shown that they could pay for their high cost of operation. Extensive test work established that by a combination of desliming, classification, and Sullivan deck treatment, cassiterite as fine as 10 microns (1500 mesh) could be recovered when proper conditions were maintained. This test work has been verified by several full-scale installations. The method is generally applicable to the preconcentra-tion of large tonnages of low-grade ores or tailings for the recovery of a small amount of a valuable heavy mineral. The Sullivan deck (or now the Denver Buckman tilting concentrator), which is the essential part of the method, was devised originally for the recovery of tin from tailings of the Sullivan concentrator, Kimberly, B. C. Since the material treated contained only 0.05 pct Sn, it was impractical to attempt to recover cassiterite finer than 500 mesh.*

Jan 1, 1951

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of deslim-ing, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants. IN the past, mills treating ores of tin and tungsten by gravity concentration have recovered very little mineral finer than 325 mesh, although some form of slime concentration has been generally attempted by the use of buddies or round tables. This paper describes a series of pilot plant tests made in 1942 and 1943 in which the use of the Sullivan deck was investigated for the recovery of an appreciable amount of the fine values formerly lost. The investigation was initiated by the U. S. Government in an effort to increase the wartime production of tin. Bolivian milling practice at that time included jigging of the coarse sizes, tabling of the intermediate sizes on conventional shaking tables, and the use of buddies or round tables on the finest sizes. Flotation of the pyrite was employed at different stages of the treatment, depending upon the quantity present and the preference of the operator. Usually good recoveries and the bulk of the production were made in the jigging and tabling operations provided that these sections were not overloaded. Buddies and round tables were used for a small additional recovery if it could be shown that they could pay for their high cost of operation. Extensive test work established that by a combination of desliming, classification, and Sullivan deck treatment, cassiterite as fine as 10 microns (1500 mesh) could be recovered when proper conditions were maintained. This test work has been verified by several full-scale installations. The method is generally applicable to the preconcentra-tion of large tonnages of low-grade ores or tailings for the recovery of a small amount of a valuable heavy mineral. The Sullivan deck (or now the Denver Buckman tilting concentrator), which is the essential part of the method, was devised originally for the recovery of tin from tailings of the Sullivan concentrator, Kimberly, B. C. Since the material treated contained only 0.05 pct Sn, it was impractical to attempt to recover cassiterite finer than 500 mesh.*

Jan 1, 1951

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015