Search Documents

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By C. K. Leith

ManGanese is one of the minerals which is principally consumed in countries other than origin. Nearly 85 per cent. of the world's production is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent. of the world production comes from Brazil, Russia, India, the Gold Coast of Africa and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this inovement is for considerable distances and is occan bornc. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metallurgical methods, only 35 per cent. of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explorations now under way, indicate no shortage from a world standpoint for many deeades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel industry uses over 90 per cent. of all the manganese mined and is acquiring control of a considerable part of the production in all of the principal fields—the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies arc of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing uneasiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few cnough to warrant the belief that more or less monopolistic elements of control arc not impossible.

Jan 1, 1927

By Vladimir Jindrich

This paper presents a history of a successful three year effort in locating a large, economic deposit of high purity limestone. The exploration program has been carried out by Ernest K. Lehmann & Associates, Inc., geological consultants, for Dravo Corporation, owner of the limestone property which is now under development. The permission of Mr. L. P. Struble, Jr, President of Dravo Lime Company, and Mr. M. W. Robinson, Director of Research and Development, to present this paper is gratefully acknowledged. The limestone property is on the Ohio River near Maysville in northern Kentucky, 60 miles east of Cincinnati (Fig. 1). The area lies at the eastern flank of the Cincinnati Arch, a regional structure where the Lower Paleozoic strata crop out below the adjacent younger sedimentary rocks of the Illinois and Apallachian basins. In general, the limestone formations of the Middle Ordovician High Bridge group offer the best potential for industrial limestone in Kentucky and adjacent parts of Ohio and Indiana. These formations are exposed along the axis of the Cincinnati Arch in central Kentucky. Toward the west, east and north, strata of the High Bridge group are progressively deeper, concealed beneath a succession of interbedded fossiliferous limestone and shale. The High Bridge group limestone formations are shallow-marine deposits largely of tidal flat, shallow lagoon and related environments. Principal lithologies include cryptocrystalline micritic limestone and crystalline dolomitic limestone to dolomite. Shale and bioclastic limestone are subordinate but the proportion of shale increases in the basal formations. Characteristic, is the occurrence of several thin beds of bentonite that serve as regional stratigraphic key horizons.

Jan 1, 1975

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

By R. Hurman Eric

The dew-point technique of activity measurements take advantage of the volatility of a component in solution. The pressure of the volatile component over a sample is determined from observations of the temperature at which condensation of the vapor occurs. The method is applicable best when the vapor pressure of the components would differ by about two to three orders of magnitude. Experimentally, this is a closed system involving the use of evacuated and sealed transparent quartz sample probes. Furthermore reliable vapor pressure data of the volatile component is essential along with a specialized high temperature furnace capable of giving reproducible results. In this context, the vertical Dew-Point Furnace (DPF) was designed and built after elaborate trails until enough proficiency was gained for reproducible results. Over the years the DPF was modified and improved. The DPF developed was versatile and could easily be used for activity measurements in the isopiestic mode (another method of measuring activities of a volatile component in a solution). The necessary ancillary systems; namely evacuation-flushing-evacuation followed by sealing of quartz sample probes under vacuum were also perfected over the years. As and when necessary the dew-point technique was supplemented by classical equilibration-quenching method employed on the sealed quartz sample probes to reveal necessary phase equilibrium information. The following were studied utilizing the above technique: (i) Activities in CU2S-PbS and FeS-PbS binaries and CU2S-FeS- PbS ternary at 1200°C; (ii) Activities in Cu2S-SnS and FeS-SnS binaries and Cu2S-FeS-SnS ternary at I200°C; (iii) Phase equilibria and thermodynamic in Cu-Pb-S, Fe-Pb-S, Fe-Sn-S, Cu-Sn-S and Ag-Sn-S systems. Most recently the following systems have been tackled: (i) Phase equilibria and thermodynamics in the Ag-Pb-S and Sn-Pb-S systems; and (ii) Activities in Ag2S-FeS-CuzS-PbS quaternary at 1200°C.

Jan 1, 2003

By L. R. Jackson

THE idea presented in this paper is that the capacity of a metal for plastic flow before rupture is dependent on the type of stress system applied-that is, the absolute magnitude of the stresses are unimportant provided that they are large enough to produce continued flow; the important factor is the "type" of stress system. A term called the "triaxial stress ratio" is defined in such a way that this ratio can be used to characterize the "type" of system. The paper is divided into three sections. The first section discusses means of representing the effect of complex stresses on plastic flow and defines "triaxial stress ratio"; the second section discusses various methods of' obtaining complex stress distribution. The third section gives some experimental results showing the effect of types of complex stress on the capacity of various metals for flow. An appendix discusses some details on methods of obtaining complex stresses. I. REPRESENTATION OF COMPLEX STRESS SYSTEMS AND THEIR EFFECT ON PLASTIC FLOW Representation of Stresses It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses [S1 S2 5 S3]. This system can be resolved into a new system consisting of the three components [ ] and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation [ ] Sm is given by Eq. I and S1 is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. [ ] Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1944

By A Tsang, D La Rosa, L Julian, W Hunt, R Pratama

Mineral extraction is facing the twin challenges of finite resources and increasing environmental and economic costs. Society’s growth is matched by an increase in demand for the earth’s resources. It is incumbent on us as contemporary mining professionals to promote and facilitate ethical and efficient practices. Technological developments have and will continue to allow a decrease in viable cut-off grades, creating new economic opportunities from deposits that were previously uneconomic. Mining low-grade deposits however, even with perfect recoveries, will have a significant environmental cost for the metal won. The greatest opportunity to increase metal with the least environmental cost is to increase the metal yield from existing mines. The determination of mining polygons is a critical juncture where rock is typically subjected to the binary grading of either ore or waste. This is undertaken using a number of factors, such as the mining equipment being used and the recovery in the processing plant. Traditionally, mining polygons were generated on the in situ grade control model. This ignores the complex differential blast dynamics that occur during blasting. Two opportunities exist to improve metal yields: optimise the blast design to achieve the post-blast muck pile that will support the greatest outcome; and generate optimised polygons on the post-blast muck pile. A data set from a Canadian Gold deposit is used to demonstrate the potential benefit of iterative blast movement modelling and grade control polygon optimisation on metal yield. The impact of blasting on the total recoverable metal is presented, highlighting blast design as a critical process in the mining value chain.

Sep 1, 2024

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By E. T. White, Dean Ilievski

"Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known. This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal ""best"" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.IntroductionCrystallisation operations, including precipitation, are widely used in a number of hydrometallurgical processes to recover a desired component or to remove an undesired impurity. The goals of industrial precipitation processes are to maximise the recovery while maintaining product quality (generally product crystal size distribution, purity and morphology and product handling properties). Knowledge of the precipitation mechanisms and kinetics is invaluable for designing new precipitators or for improving existing units. The mechanistic and kinetic information is generally incorporated into mathematical precipitator models, which are then used for process design and optimisation."

Jan 1, 1996

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

In 1967 the United States consumed 58.8 quadrillion Btu of energy. Both the Atomic Energy Commission and the Resources for the Future, Inc., a private economic forecasting group, predict that the United States energy requirements will reach 135 quadrillion Btu by the year 2000. In 1967 bituminous coal produced 21.4 percent of the energy used in the United States and anthracite coal another 0. 5 percent. Coal Reserves Coal reserves make up about four-fifths of the United States storehouse of fuel in proven reserves. Seventy-five percent of all fuel, likely to be found and recovered is coal. Electric utilities consume more than half of the bituminous coal mined in the United States in generating 53 percent of the nation's electricity. Atomic Energy Commission analysts have proposed the development of a vast "national energy system" based upon long-distance electrical transmission from abundant untapped coal reserves in the western United States. The study predicts that even if uranium supplies are available and economic breeder reactors developed, coal requirements for electricity generation will more than double by 1980 and increase another 50 percent before the year 2000.

Jan 1, 1970

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By F. L. Bosqui

The history of the development of gold metallurgy in South Africa is divisible into two periods: That preceding the introduction of the cyanide process on a commercial scale in 1890; and the 24 years intervening between that important event and the present time. The period between the discovery of the banket reefs of the Witwaters-rand and the year 1890 was one of phenomenally rapid progress in mining development, but of no special interest to the metallurgist, There were no strikingly original or distinctly local advances in the treatment of gold ores. Californian practice in stamp milling and amalgamation prevailed, in mills ranging in equipment between 5 and 50 stamps, operating within a wide range of efficiency, and under the trying conditions usually encountered in a new and isolated field. The somewhat incomplete records of gold output of that period show that in December, 1887, there were 20 producing companies in the Witwatersrand district, of which 10 had mills, the largest being of 20 stamps. The only official record of returns for May, 1887, was that of the Wemmer mine, whose modest achievement with a 5-stamp mill was 100 tons crushed, producing 887 oz. 3 dwt. of gold. This is interesting in view of the present-day output of this field, which in 1913 reached 8,430,998 oz. The rapid increase of production during this first period (May, 1887, to January 1891) is shown by the following summary for the year 1890:1 Total tone crushed.................................. 702,828 Number of stamps in operation....................... 1,046 Average number of tons crushed per stamp per day..... 2.36 Yield of gold, ounces................................ 494,817 Yield per ton, pennyweights.......................... 13.36 The stamp duty ranged between 11/2 and 4 tons per day, according to weight of stamp, fineness of screen, and operating skill available. The prevailing weight of stamp was about 900 lb., and the screen, 900 meshes to the square inch.

Jan 1, 1916

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Carle Hayward

AT THE February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500° it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. cooperated by furnishing the steel and turning the tensile specimens.

Jan 1, 1922

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

By M Dixon, T OÆShannessy

Melbourne Water (MW) is responsible for a section of existing gravity trunk sewer servicing the Melbourne central business district, Docklands, Port Melbourne and other adjacent areas, known as the Melbourne Main Sewer (MMS). MW has determined that the 2.2 km long 110 year old sewer will not adequately service these areas into the future or provide the level of reliability needed. The Melbourne Main Sewer Replacement project (MMSR) involves the replacement of the MMS with a new gravity sewer main and six key manhole shafts, known as the Melbourne Main Reliever (MMR).The majority of the MMR sewer tunnel is situated south of the Yarra River and will be constructed using an earth pressure balance (EPB) tunnel boring machine (TBM) and will be lined with precast concrete segments. The tunnel will be 2.4 m internal diameter and will have a 1.8 m diameter glass fibre reinforced plastic (GRP) sewer pipe positioned within it. This project represents the first large-scale, modern, mechanised tunnel project in MelbourneÆs Yarra Delta Quaternary sediments. There is little precedence known to the authors of similar scale tunnelling projects in these particular geological units. During the recent detailed investigation and design stages of the project, significant effort has been spent on characterising the geotechnical conditions along the alignment and predicting the effects of the new tunnel on the existing environment. Some of the key design issues that have been identified and managed through the design process include short-term surface settlement due to tunnel excavation and the predicted effects on surface infrastructure, potential spalling of the steel fibre reinforced concrete segments under full TBM ram loads and tunnel lining design in geological units with highly variable stiffness.Construction of the new MMR sewer tunnel is expected to commence in mid-2008 with a capital cost of approximately $160 million. Sewer system commissioning is scheduled for completion by early 2012.

Jan 1, 2008