Search Documents

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Ricardo Ponce

In recent years, ENAMI implemented modernisation plans at its two smelters in order to meet the government's environmental regulations introduced in the early 1990s. The modernisation plans defined the new SO2 and particulates emission targets, deadlines for compliance, and the revised treatment capacities of the smelters. At Las Ventanas smelter, the principal process change consisted of eliminating the reverberatory furnace. All the smelter feed is currently processed in a 4m diameter, 14m long Teniente Converter, using up to 34% oxygen enriched air. Dry concentrate is injected into the bath through tuyeres. A fuel oil burner compensates for any process heat deficiency. The Teniente Converter high copper content slag is cleaned in an electric furnace. This furnace is also used to melt internal reverts. This paper will discuss the successful operation of the slag cleaning electric furnace.

Jan 1, 1999

By M. Z. Rashad, H. A. El-Sageer

The intersections of numerous joint sets at the surface of tunnels of the Abu-Tartour project in Egypt create blocks of irregular shape and size in the rock mass. Although most of these blocks are unable to move into the free space of the tunnel, a few key blocks are capable of such movement. In addition, as soon as they move, some restrained blocks will be liberated. The aim of this work is to find the removable key blocks of the walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks and then determine the best tunnel direction.

Jan 1, 1993

By W. E. Hale

The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Programme (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature: during approximately six weeks an orientation survey, involving, geology, geophysical surveying, and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Sto. Nino (Fig. 1). The Sto. Nino study demonstrated (Hale and Govett, 19677 Govett and Hale, 1967) the feasibility of geochemical prospecting relative to other exploration methods for the location and delineation of disseminated copper occurrences, the major source of metal in the expanding mineral industry of the Philippines. A vein occurrence at Suyoc (Fig. 1) was similarly subjected to

Jan 1, 1968

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By Robin N. Adair

Abstract -The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotite­ rich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphie hanging wall. This sequence is stratigraphically overlain and locally interfmgered with matie volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basait to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship be­tween the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By Irving Hartmann

The record of safety in the use of permissible explosives in United States coal mines has been excellent, due in great measure to the persistence with which research has been carried on in the Bureau of Mines, to the development of permissible explosives, and to the cooperation of mine operators and workers in using permissibles in a recommended manner and in the effective though gradual replacement of black powder and other nonpermissibles. The demand for increased rate of coal production, changes in mining conditions and minim methods, and introduction of new mining machinery have resulted in modified or new blasting practices. To keep abreast of these developments the Bureau of Mines conducts investigations under actual mining conditions at the Experimental coal mine near Pittsburgh, Pa. Several years ago an extensive study was complete to determine conditions under which the allowable charge limit for permissible explosives per shot hole might be raised from 1.5 to 3 pounds without undue risk of gas or coal-dust ignitions. As a result of the study, this increase in the charge limit was authorized under certain specified conditions in 1948,5/ greatly facilitating production schedules.

Jan 1, 1954

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By H. Scott Swinden

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum . Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This second paper (the first was by Fyffe, et al., in Vol. 83, No. 938) in the series presents an overview of the paleotectonic settings of massive sulphide deposits in the Dunnage Zone of Newfoundland with emphasis on volcanic geochemistry.ABSTRACTCambrian and Ordovician volcanic sequences of central Newfoundland, which record the history of the Iapetus Ocean, are prolific hosts to volcanogenic massive sulphide (VMS) deposits. Geochemical, isotopic and geochronological studies show that the vestiges of Iapetus in Newfoundland probably record a complex series of island arcs and back-arc basins that were marginal to, rather than part of, the main ocean basin of Iapetus. The geochemical and isotopic data provide a means of characterizing the tectonic environment of individual volcanic sequences, and allow us to identify a number of distinct tectonic environments in which VMS depositiontook place.Four tectonic environments have been identified as being associated with VMS deposition: (I) back-arc environments hosting VMS deposits include both N-MORB-type ophiolites (e.g. Skidder?) and volcanic sequences with oceanic island (or within plate) tholeiite characteristics (e.g. Great Burnt Lake); (2) primitive arc environments include both supra-subduction zone (SSZ) ophiolites (e.g. Betts Cove, Rambler) and volcanic/epiclastic sequences (e.g. Point Leamington, Duck Pond) and are characterized by abundant arc tholeiites, with lesser refractory lavas and rhyolites; (3) mature arc environments comprise dominantly thick felsic and mafic volcanic piles in the Buchans - Robert's Arm Belt (including the Buchans camp) and are characterized by dominantly calc alkalic basalt and andesite; and (4) continental rift environments occur in the Hermitage Flexure area (e.g. Strickland deposit) and are characterized by dominantly felsic volcanic sequences.Island arc environments are by far the most prolific hosts to VMS deposits. Patterns of VMS distribution in central Newfoundland show that similar tectonic settings may be recorded by very different stratigraphic sequences (e.g. both ophiolites and thick volcanic/ epiclastic sequences may record primitive arc rifting) and emphasize the importance of the rifting in VMS generation, irrespective of the details of the tectonic or stratigraphic setting. The ability to judge the prospectiveness of a volcanic sequence by using whole rock geochemistry to evaluate its tectonic environment may prove useful in area selection at the grassroots exploration level."

Jan 1, 1991

By Arturo M. Morales

INTRODUCTION Manganese carbonates are nodulized by Cia. Mineral Autlan, located in Ongongo in the state of Hidalgo in Mexico. This kiln is fed minus 15 mm material at the rate of 1870 tpd. About 920 tpd is nodulized into a commercial product having a size range of 15 mm to 12 mm. The kiln also produces about 320 tpd of minus 12 mm fines and 40 tpd of chimney dust. Currently, the minus 12 mm fines are being recirculated to the kiln and the chimney dust is not being utilized. It has been found that there exists a market for manganese to be used as feed to the ferromanganese and silicomanganese furnaces. However, a coarse, lumpy feed can only be used in these furnaces. Accordingly, it has been proposed to screen the fines at 6 mm and agglomerate the minus 6 mm fraction along with the chimney dust and suitable binders. This paper presents the results of a feasibility study and test work aimed at producing an acceptable agglomerated product from the kiln fines for use in the ferromanganese and silicomanganese furnaces. Since the agglomerated product will have to be handled and loaded into trucks in the kiln area and transported over long distances, a minimum strength of 200 N is expected to be necessary. They should also have enough initial strength to be stockpiled and result in a minimum of breakage. A third important requirement is that the agglomerates should be resistant to disintegration during combustion. The recirculating fines were to be agglomerated in their original state, if possible, that is, without grinding. This eliminated the possibility of pelletizing as an agglomeration method. Based on a few laboratory trials, the briquetting method seemed most attractive, and a test program was initiated to explore the briquetting process.

Jan 1, 1977

By P Holtham, R Dunne, D Stoll

Flash flotation is a process designed to remove coarse, liberated, fast floating minerals from hydrocyclone underflow. Irrespective of liberation, coarse particles would normally remain in a grinding circuit until they are reground fine enough to report to the hydrocyclone overflow. Additionally, minerals of high density also report to hydrocyclone underflow despite being fine in size and/or liberated because hydrocyclones separate on the characteristics of both particle size and density. Dense particles continually reporting to the hydrocyclone underflow can lead to over-grinding and the production of ultra fine particles. These particles exhibit slow flotation kinetics and thus are difficult to float in conventional flotation circuits. Therefore, removing coarse, liberated particles from the hydrocylcone underflow by flash flotation has the potential to improve recovery and can improve dewatering unit operations and reduce grinding costs.The impact on the overall performance of the flotation circuit by removing coarse, fast floating minerals prior to conventional flotation is not well understood. Ultimately, predicting the overall recovery improvement provides the justification for the installation of a flash flotation cell within the milling circuit. This paper will describe attempts to estimate flash flotation recovery improvements to the overall circuit using kinetic data from simplified batch cell flotation tests combined with limn-based modelling techniques.CITATION:Stoll, D, Dunne, R and Holtham, P, 2012. Modelling the impact of flash flotation from batch cell flotation tests using limn, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The middle-Devonian Dulladerry Volcanics is a complex of A-type, predominantly rhyolitic ignimbrites, lavas and breccias. They form a NNW trending belt some 90 km long and 10-20 km wide, east of Parkes, NSW. The volcanics are dominated by widespread ignimbrite units with minor basalts, sediments and rarer andesites. The volcanics were deposited in a sub-aerial, possibly continental rift setting and are similar in chemistry and age to the Eden - Comerong - Yalwal Volcanic Zone (EVZ) on the NSW south coast. The volcanics exhibit an unusual Atype chemistry (high Zr, Y, Nb, REE, Ga). This distinctive composition illustrates that the volcanics are not comagmatic with the adjacent Yeoval Granite Complex or Eugowra Granite, which show typical I-type fractionation trends. Epithermal gold veins occur in basalt and andesite in the Dulladerry Volcanics at Mt Aubrey (Hopf, 1992), near Baldry. Alteration also occurs in the Glen Isla and Red Hill areas, with epithermal sinter recognised at Glen Isla. Copper and minor gold mineralisation occurs at the contact of rhyolite and andesite at Reedy Creek, but is not of epithermal origin. The analogous EVZ also contains several epithermal gold fields and it is this style of mineralisation which provides the most prospective targets in the Dulladerry Volcanics. Although the Dulladerry Volcanics also contain high background levels of REE and metals such as Zn and Pb, the general lack of fractionation and water-undersaturated character of A-type magmas does not lend itself to the development of significant concentrations of these elements into a fluid phase and mineralisation. The prospectivity of A-type volcanics in general could not be regarded as high. However, an indicator of some fractionation in the Dulladerry Volcanics is provided by the fairly low abundance (average 230 ppm) and wide range (

Jan 1, 1995

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By H. M. Howe, A. G. Levy

§ 1 Introduction.—This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have proceeded chiefly by noting the temperature at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper1 issued simultaneously with this, while in a third paper2 one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. The Composition of the Steels Experimented On is given in Table I. § 2. Notalion and Definitions.—Following Osmond's development of Tschernoff's notation, in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range " SE," we may go farther and call this latter limit " SEc" when observed in heating up and " SEr " when observed in cooling down. Further, we may call the equilibrium position of these lines, i. e., the position which they would have in pure iron-carbon alloys if all

Jan 1, 1914

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By M. Hekmati, M. R. Garmsiri, S. M. Hosseini

"SAG/AG mills have been most common choice in grinding circuits last decades. In the most cases, at the discharge of SAG/AG mills, a trommel screen is used that is equipped with baffles to provide appropriate residence time and improve separation efficiency. Using baffles, with the resultant maintenance requirements could lead to decrease in mill availability. In this research, an innovation in the structure of baffles of a trommel is presented. The results show that using new baffles led to 67% decrease in SAG mill downtime due to problems of baffles and 80% decrease in fine particles on recycle conveyor.INTRODUCTIONComminution is a vital operation in mineral processing circuits and it helps to achieve a certain level of fineness in the ore material. About 60-80 % of the overall energy used in mining is consumed in comminution, and this is the reason that much research has been performed in this field (Kochnev, 2008).During the last decades the configuration of grinding circuits has been changing due in large part to the decrease in the grade of mineral resources and the need for large scale, energy efficient processes. The previous configuration of conventional grinding circuits was based on parallel primary circuits (mostly using ball mill), such as the grinding circuit of Sarcheshmeh concentrator plant no.1 (Figure 1). The new configuration of grinding circuits is based on using SAG/AG mills, such as Shahrebabak concentrator plant (Figure 2), sometimes incorporating new technologies like the HPGR. Nowadays, application of new configuration of grinding circuits using large SAG/AG mills up to 40 feet (Allan, Major, Flintoff, Klein, & Mular, 2006), in the minerals industry is continuing increase due to the significant reduction in capital and operating costs, and increase in the plants throughput (Banisi & Hadizadeh, 2007)."

Jan 1, 2012

By V Lawson

Vale’s Sudbury Clarabelle Mill processes Cu/Ni ores from a number of mines in the Sudbury basin in Ontario, Canada. Bulk sulphide flotation produces a copper-nickel concentrate with pyrrhotite as the major diluent. After successful commissioning of the Voisey’s Bay Cu/Ni Mill (VBN) in Labrador, a miniplant campaign on Clarabelle ore with the VBN flow sheet produced a significant recovery improvement over current performance. In 2001, the Mill Redesign Project moved grinding energy into rock/sulphide and pentlandite/pyrrhotite separation and in 2006 Cu/Ni separation was re-introduced to Clarabelle Mill to produce a saleable Cu concentrate. The projects were a great success. What remained was to simplify the Clarabelle flow sheet by introducing the missing components found in the VBN flow sheet. This project known as CORe has evolved through many stages including the mining boom and surviving the 2008 economic downturn and it is scheduled for completion in mid 2013. This paper outlines some of the challenges faced in this major brownfields project – organizational, technical, financial and operational.

Aug 8, 2011

Optimal drill and blast design is a process often neglected by many underground hard rock mines. This is even more important to the new mine where ring designs need to be implemented and refined in a short period of time. In today's environment where more and more mining is being carried out by contract specialists it is the co-operation between a principal and contractor, who are working towards a common goal, that achieves the highest quality end result. The development of drill and blast designs that cause minimal damage to the mine infrastructure is particularly important to Northparke's E26 Block Cave Mine, as it consists of a single extraction level which must survive intact for the life of the mine. The advanced undercut mining method implemented at Northparkes is fired in a sequence which protects the mine development from potentially damaging abutment stress. This paper details how blast designs will be optimised and sequenced to satisfy the conflicting objectives of maximum rock breakage inside the drill pattern and minimum rock damage outside the pattern.

Jan 1, 1995