Search Documents

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

By B. D. Wood, J. A. Fowler, H. S. Grütter, J. M. Kong

Abstract- The phased approach used by De Beers for diamond exploration is briefly outlined. The Victor kimberlite is one of 19 kimberlites in a cluster near Attawapiskat, Ontario. The progress at the Victor kimberlite is summarized, and the operations are described within the framework of this staged approach. An evaluation program is currently under way on the Victor kimberlite, but although results are encouraging, insufficient diamonds have been recovered to permit disclosure of estimates for the grade and value.

Jan 1, 2001

By F. M. Makarinsky

"SynopsisThe Kanichee open pit mine and milling complex is situated approximately four air miles north-west of Ternagami, Northern Ontario, in Strathy Township. Mining and milling production commenced in January 1974.Milling throughput currently is at a rated capacity of 500 tons per day, seven days per week. A bulk nickel-copper sulphide concentrate is produced, and is trucked daily to the smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, some 120 road miles from Kanichee. Concentrate grades produced are in the order of 4.0% Ni and 8.0% Cu, with corresponding recoveries of 68-70% nickel and 86-90% copper. Stage additions of 100% guar-gurn solution reagent to the flotation cells for depression of talcose minerals, proved to be the major break-through for optimizing metallurgical performance.2. HistoryThe present Kanichee Mining property is known to old-timers in the Temagami area as the former Cuniptau Mine. Several attempts were made in the mid '30's and 40's to extract the ore at a profit, but each effort resulted in failure.In 1933-36, Cuniptau Mines Development Co. Limited, later called Cuniptau Mines Limited, sank a 245-foot vertical shaft and completed 2,200 feet of lateral work on the 100-140 and the 225 foot levels. Fifteen tons of ore were sent for testwork to the Mines Branch, Ottawa, Ontario.Cuniptau Mines Limited, in 1936, milled some 3,000 tons, and the resulting concentrate was put through a pilot smelter situated on the present mine site. Metallurgically, the smelting results were not encouraging, primarily due to the high melting point of the talcose minerals in the concentrate. From the period 1937-48, minor exploration work was done by Ontario Mining Corporation, Ontario Nickel Mines Limited, and Trebor Mines Limited. During the period 1948-49, 128 diamond drill holes, totalling 40,900 feet were evaluated by Trebor Mines Limited. In 1961, the name was changed to Ajax Minerals Limited, during 1968, five diamond drill holes were sunk, totalling 1,700 feet. Since that period the property has remained idle."

Jan 1, 1975

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By M. A. Giralico

A new generation of hydraulic efficient pumper and auxiliary impeller designs is the result of an extensive research program focused on improving the overall performance of optimized SX/EW plants. Combined with the proper scale-up, these optimized designs will greatly reduce aqueous and organic entrainment losses, reduce or eliminate air entrainment and crud formation, enhance mass-transfer and maximize the overall copper yield. Currently, these new pumper and auxiliary impellers are installed full-scale in numerous plants ranging in flow rates from 90 to 15000 G.P.M. and developed heads up to 51 inches. Operational results reported by the independent metallurgist at each processing plant are reporting the lowest entrainment results in the industry. Further R&D has just been completed on a new mixing configuration that separates the systems mixing and pumping requirements. Results from the system pilot test document further improvements in reduction of both chemical entrainment and crud formation, while keeping mass transfer stage efficiencies.

Jan 1, 1998

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

By K. B. McQuillin

The volume of data resulting from an intensive search for new coalfields necessitated the establishment of a computer based processing system for coalfield data. The development of this system over the past seven years is described, with particular reference to the problems encountered in both the design and operation of the data base.

Jan 1, 1977

By A. Davis, C. Webb, J. Sorensen

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM). The mine produced lead and zinc during the first half of the 1900s. Because of acidic drainage and elevated levels of metals in tailings and waste rock, the site was evaluated in 1998 and 1999. After evaluation, the mine was remediated during 1999-2001 by the BLM. Since remediation, values of pH in water samples have been nearly neutral and specific conductance values have been much lower than before remediation. The Grizzly Gulch forest fire of July, 2002, consumed much of the Belle Eldridge site and resulted in greater than normal erosion and sediment flushing during the months following the wildfire. Had the site not been remediated and the tailings emplaced within a capped repository, generation of acidity and off-site migration of heavy metals within sediments could have been severe at downstream locations.

Jan 1, 2007

By C. H. Bucknam

A suite of ore and waste rock materials was selected for the interlaboratory testing of combustion-infrared ("Leco") methods used to estimate carbonate and sulfide minerals present in test materials. The objective of the study is to develop ASTM standard methods to be used for metallurgical characterization of ore, acid drainage prediction for ore and waste during ore body evaluation, and for ore and waste control during the active mining of ore deposits. The results may be interpreted for classification of the materials according to their carbonate-sulfide or acid-base characteristics based on net carbonate value (NCV). The test materials were processed by x-ray diffraction and x-ray fluorescence (XRD-XRF) at Newmont Metallurgical Services (NMS) to obtain a semiquantitative mineralogical composition. Results of the interlaboratory testing for total carbon-sulfur, pyrolysis loss carbon-sulfur and hydrochloric acid residual carbon¬sulfur are compared with the mineralogical composition to aid in interpretation of the NCV classifications of the samples.

Jan 1, 2002

By Sarah Wilson, John Kaplin

Plans are underway to extend commuter rail service underground into downtown San Francisco. The Salesforce Transit Center (STC) was completed in 2018 and will serve as a new transit hub, including a commuter rail station after two future connecting tunnel segments are completed. The northern segment, known as the Caltrain Downtown Extension (DTX), which will extend the rail line from its current terminus at 4th and King Streets to the STC, is currently in Preliminary Engineering. The southern segment, the subject of this paper, is a 1.6-mile tunnel known as the Pennsylvania Avenue Extension (PAX), which is currently in the pre-environmental planning stage, with alternative alignments under evaluation including single bore versus twin bore options. This paper discusses project challenges, including highly variable tunneling conditions in soil and rock, a congested urban project site with limited space for construction staging, alignment crossings of large existing buried infrastructure, and complicated interfaces with future and existing rail operations.

Dec 1, 2022

By Lawrence Piccagli

This past spring of 2006, BENCOR installed the concrete reinforced diaphragm walls for the COSMOPOLITAN RESORT & CASINO in Las Vegas, Nevada. The project highlights include the excavation of approx. 326.000 square feet of reinforced diaphragm slurry wall with a thickness of 30 inches and a depth of 100 feet using three reverse circulation trench cutters (hydromills) at the same time. The reinforcing steel cages were fabricated on the 8 acre jobsite and approximately 12,000 cubic yards of 4500 psi concrete was placed via tremie. The jobsite logistics of coordinating three trench cutters and three separate desanding/slurry plants as well as the reinforcing steel fabrication and concrete placement all under a very tight schedule was quite challenging. A second main exercise was the execution of a temporary excavation support. As the excavation depths extends between 66 and 72 feet, five to six rows of temporary tieback anchors were required. Anchor lengths range from 43 -83 feet at a maximum design load of 235 kips.

Jan 1, 2007

By Zhansen P

This paper describes the test re- sults which give a complete proccess of failure of concrete lining embedded in sand medium under load, including the order of appearance of crack along the lining up to failure. nor each crack appearance corresponding calculation being made to assess the redistribution of moment and thrust force in critical section including crown section, section making 45¦ with the vertical etc. De- flection at the above stated critical sections are also measured at each stage of loading. The pressure along the top hori- zontal surface of embedded lining and the vertical sides are measured by pres -sure gauges embedded in sand medium. fhe test results show a complete figure of rupture characteristics of concrete lining embedded in soft ground which approximates alluvial deposite often occur in metro construction at cities near the river side. These test results have been taken as a reference in assessing the action behavior of concrete lining in certain cities in China.

Jan 1, 1987

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

The Regional Development Council has initiated a project that aims to find better ways for further investment by extractive industry companies in sustainable regional and community futures. It will be undertaken through collaborative actions that bring together the resources of private and public sector stakeholders in regional Western Australia.   The broad objectives of the project are to: describe and analyse the current situation with respect to the impediments to regional communities being more self sustaining, assess the effectiveness of the current and possible future levels of investment by extractive industry companies in the sustainable development of communities in regional Western Australia, identify and demonstrate collaborative ways in which extractive industry companies in Australia and other countries can play an enhanced role in sustainable regional and community sustainability through strategic engagement and investment; and confirm the effectiveness of the collaborative measures in delivering sustainable outcomes for regional communities by way of attracting and retaining populations and enterprises in Australia and similar environments.

Jun 1, 2010

By R. L. Minckler

PETROLEUM industry forecasts are constantly made and revised but are not in the nature of predictions. Particularly in the field of demand, many of the factors are far beyond control by the producing industry. Supply reacts on demand and demand reacts on supply. Competent economists in the oil business forecasted a year ago, on the basis of experience, that demand would now be at a much lower level than it is. This increased demand increased the price of crude oil and products, and in turn those increased prices have brought forth increased supply. A reduction in demand would lead to a reduction in supply. Shortages are now world-wide, and costs of secondary importance, so if there were extra supplies in California they would be moved into what are termed "unnatural markets." For example, Argentina is in the market today for California gasoline; that is an unnatural market because of the greater transportation distances from California to Argentina than from normal sources.

Jan 1, 1947

By R Thompson, D Tulloch

"Wet-weather or 24×7 wet-trafficability is a commendable design objective for unpaved mine haul roads, but practically often difficult to achieve, due both to the road sheeting material selected, and also its breakdown under the action of traffic and environment. Accidents allied to wet-trafficability issues, either due to rain or often more commonly, over-watering of mine roads, is increasing and especially the loss of control or uncontrolled vehicle movements categorisation. The dominant system failure is that once vehicle control is lost, control cannot be regained.The friction supply, or ‘skid resistance’ of a mine haul road sheeting is critical to the safe operation of the road and data has to be collated concerning the variation of friction supply with sheeting material engineering or indicator properties. In the light of the paucity of data existing in this field, this paper presents the contributory research that informs the development of improved and validated unpaved mine road friction supply estimates, based on a number of mine site evaluations across a range of sheeting material types and characteristic parameters, leading to improved predictive models of friction supply.Results from this preliminary review will enable operators to assess their road sheeting materials, improve and validate unpaved mine road friction supply estimates. This will contribute to improved road design, management and 24×7 operability decisions and contribute to a reduction in heavy vehicle loss of control incidents on gravel-surfaced mine haulage roads.Citation:Thompson, R and Tulloch, D, 2016. What's Stopping You? The Role of Sheeting Material Selection in Safe Haulage Operations, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 253–264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016