Search Documents

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum's book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum's book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941

By K A. Pericieous

"Magnetic fields have many actual applications in the metals processing industry. Externally applied magnetic fields give rise to electromagnetic (Lorentz) forces formed by the cross product JxB, between the induced current density J and the magnetic field density B. When the metal is in liquid form, the Lorentz force generates motion in the fluid which in applications of practical interest becomes turbulent. In modelling terms, the Lorentz force appears as a source in the momentum equations. In addition, the induced current generates heat (Joule heating) in the metal that is in proportion to J2, with a corresponding source of heat in the energy equation. Whether as heat or as a force, these effects represent action at a distance - a most useful attribute when dealing with hot metal. The Lorentz force is used to stir solidifying alloys, pump liquid metal in conduits, dampen the flow in the meniscus of a continuous caster, levitate metal drops, induce artificial gravity conditions in suspensions or contain liquid metal. Elsewhere, the Lorentz force may be a by-product of some other operation, so leading to wave excitation in aluminium electrolysis cells, or altering the shape of the weld pool in arc welding. Joule heating is most commonly used with applied AC fields, to melt metal in induction furnaces.The author and his colleagues have been involved in the modelling of most of these processes in the past decade. Modelling is not however straightforward, since most of the examples mentioned represent genuine multi-physics challenges. There is a strong coupling between the flow field and electromagnetic field. The addition of a dynamically varying metal free surface and the moving solidus front means the flow, heat and electromagnetic fields need to be computed simultaneously. In situations involving metal containment, the metal free surface position is governed by the interplay of gravity, Lorentz force, surface tension and fluid inertia. Since all the interesting effects often happen in thin boundary layers at the surface due to the skin effect, mesh generation and mesh control during the computation become non trivial problems that need to be addressed. This paper presents a review of numerical methods used to model droplet levitation, semi-levitation melting and cold crucible induction melting of metals. The first method is based on spectral collocation techniques and the second is the traditional FV approach. Steps taken to validate the computations and typical transient results are also given."

Jan 1, 2001

By J. P. Givry

The bath and the liquid metal in the aluw~inuw~ electrolytic cells are moving under the action of the Laplace forces. Consequently there are differences in level at the interface of the liquid. This phenomena is studied by means of a computer; the characteristics of the mathematical model used are presented with the results corresponding to two typical cases. This study gives a new and origi~zal interpretation of magnetic ej-jects; their action depends very closely on the hydraulic phenomenon which explain the sensibility of the cells to the slope and thickness of solid bath frozen around the pot. MAGNETIC effects produced in the electrolytic cells used for the production of aluminum are known to exist, a factor whose importance is well-known by producers through its influence on cell operation and output. In particular, these effects bring about movements in both the bath and metal as well as interface variations in level that are detrimental to sound electrolysis . A direct study of these effects by means of an experimental device would raise a number of problems particularly difficult not to say impossible to solve in the present state of techniques. It is for this reason that we had recourse to an electronic computer for working out the speed and pressure distribution within the liquid in the cells. We have assumed that all other possible causes for movement, such as thermal convection and evolution of gas at the anode, are acting without any connection with magnetic effects, and that consequently we may study each of these causes separately. A basic cause for magnetic effects lies in the presence of Laplace forces within the bath and metal. Electric current and magnetic field distribution have been calculated with the help of an electronic computer, and two communications about it have already been made to AIME.* 1) PRESENTATION OF THE MATHEMATICAL PATTERN In order to solve this problem, it was essential to assume a number of simplifying hypotheses with regard to both the geometry of the actual cells and the phenomena themselves. A first simplification consisted in assuming that the movements of the conducting liquid modify neither the electric currents nor the magnetic fields. In consideration of the magnitude of the values involved this assumption seemed accep-tible. 1.1) Finding the Equation of the Problem. The problem raised consisted in determining the flow of two viscous immiscible liquids with different densities subjected in a complex environment to gravity and Laplace forces. As a matter of fact, the sum of the external forces acting on the liquids is: F = JAB +pg where F = volume energy, B = magnetic field, J = current density, p = specific gravity, g = gravity. In the case of a laminar flow and assuming that the liquids are Newtonian and incompressible liquids, the equations governing movements are the following: 1) Navier Stokes' equation written in vectorial form: In fact one tries to find a steady-state solution, so aVx/at = 0; besides, one assumes that the movements are slow enough for quadratic terms such as Vy(a Vx/ay) (of round about the square of speed) to be neglected in front of the viscosity term: pAV, so

Jan 1, 1968

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By Earle E. Schumacher, Alexander G. Souden

IN the field of physical metallurgy it is becoming increasingly difficult to keep abreast of the recent develop¬ments since the diversity of investigations is so great and the literature so voluminous. The purpose of this review is to present the more important advances in the nonferrous field during the past few years, the topics discussed being classified broadly as fundamental and practical. The former includes those studies that have done most toward developing the basic science of metals and alloys, and the latter includes technical developments and applications. With the rapid growth of the metal

Jan 1, 1938

By H. A. Baxter

THE Eustis concentrator is located about nine miles southwest of Sherbrooke, on the main line of the Quebec Central railway. The concentrator is served by a side track parallel to the main line, and all supplies for both the mine and mill are delivered at the mill yards. The concentrator treats 250 tons of copper-iron ore daily by preferential flotation, whereby, first, the copper sulphides are floated and the iron pyrite is depressed, and, second, the iron pyrite is reactivated and floated, resulting in an iron pyrite concentrate and tailing, the latter going to waste. During 1934, 71,709 tons of ore were treated, averaging 3.712 per cent copper and 32.1 percent iron, with a small amount of silver and a trace of gold. The recovery was 93.77 percent of the copper, and 70.43 percent of the iron as iron concentrate. The copper concentrate produced averaged 25.623 percent copper and the iron-pyrite concentrate averaged 42.13 percent iron and 49.173 percent sulphur. HISTORY The first mill at the Eustis mine was built in 1904 (1). For a few years previous to this rime, some jigs had been operated to concentrate the fines from the mine, the coarse ore being hand-sorted. Both the fines and sorted lump ore were shipped to acid plants. The building of the mill was based on test work carried out by Professor Robert H. Richards at the Massachusetts Institute of Technology. The method of concentration consisted in careful classification in a Richards classifier, which made six different sized products. These products went to Wilfley tables, where a concentrate, middling, and tailing were made. The middling was returned to the rolls. Crushing was done by a jaw crusher and two sets of rolls, resulting in a screen size of about five-mesh.

Jan 1, 1936

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

S. A. Tomich (Consulting Geologist, Perth) : I would like to commend Mr. Haycraft on his presentation on the economic geology of the North End of Kalgoorlie. This is an intriguing area which is in the Kalgoorlie field but not of it, inasmuch as it is separated spatially from the main Golden Mile by the Golden Pike Fault. Mr. Haycraft has stressed the differences-the mineralogical and structural differences of economic significance between the two areas.I would like to ask whether he is satisfied that the lithological sequence in the North End is the duplicate of that in the main Golden Mile area irrespective of the postulated effects of erosion, and more specifically whether there is any chance that the quartz-dolerite-greenstone of the North End may be in any way dissimilar from the quartz-dolerite-greenstoneof the Golden Mile which is tellurude bearing.J. A. Haycraft: In relating the quartz-dolerite in the Hannan's North-Mount Charlotte area back to the Golden Mile, we find some quite close similarities. Although the rocks are similar they are not necessarily one and the same.At Mount Charlotte we have three varieties of dolerite- a coarse-grained gabbroic dolerite on the eastern side of the orebody, the host rock medium grained and on the western side, a fine grained dolerite. Further west we have an amphibolitic variety of quartz dolerite.Recent drilling south of the Golden Pike fault on the Enterprise No. 20 level had indicated a remarkably similar sequence of rocks. We drilled west through a wide section of medium grained rocks into a fine grained rock and then into amphibolitic quartz dolerite before intersecting the Golden Pike fault. Williamstown dolerite was located west...

Jan 1, 1965

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,' in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young's modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.'" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase 'Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By Jose Lara

SIDOR has developed a setup model for a roughing mill with edger that optimizes the position of the edger for a better control on the width, optimizes the efficiency of the mill for controlling of the profile of reductions and increments of the speed rolling and improves dimensional performance. This model consider as data entry, the number of passing, incoming and finish thickness and width, hardness and temperature of the material. The setup model is based on the equations of Ekelund for the width spread calculation and estimates of the rolling force. Additionally this model employ a Newton's algorithm for resolving the optimal position of the edger. The preset values calculated by setup model is the horizontal screw position, vertical screw position (edger), threading and rolling speed, some parameters calculated for the correction of ski. In the revamping of the roughing mill of hot rolling of SIDOR, C.A, carried out in January of 2005, it was implemented this setup model and the coefficients and parameters were adjusted for the first 15 days. Starting from there the values of preset, send to roughing mill are calculated by this setup model. The current indicators show an enhancement of 18% in the roughing mill effectiveness and a decrease about 37% in the mill stop by overload in the motors.

Jan 1, 2006

By T. W. Guy

DuRing recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures. Early Cleaning Methods In the early days, the tipples were simple wooden structures, with bar screens for separating the fines from the lump coal. All cleaning was done by the miners at the face, or by pickers in the railroad cars. Gates were provided in the chutes by which the flow of coal could be stopped when necessary while the pickers raked the surface of the coal in the car and picked out the impurities. A large percentage of the fine coal or slack was used for making coke at the mines in beehive ovens. The

Jan 1, 1932

By J. F. Wolff

During the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision were done in a few instances only. The demand for refinement of work in .this direction has led 'the engineers of the Oliver Iron Mining Co. to do extensive structural subdivision and correlation in all exploration work during the past 4 years. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Rangc, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7,1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principal feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will be as follows : I. General geology. 11. Subdivision of Biwabik iron-formation. 111. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgnlent is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron Mining Co., for permission to use the information presented in this paper.

Jan 1, 1917

By H. C. Chao, W. F. Hosford, L. H. Van Vlack

The negative "plastic Poisson's ratio" suggested in earlier studies of Mus deformation is analyzed, and the results are verified experimentally with NaCl crystals. In the early stages of deformation where the primary {110}(110) slip predominates, compression along. the [001] direction produces contraction along the lateral [011] direction plus a compensating expansion along. the [100] direction. With additional strain, the primary slip is supplemented by secondary {111}(110) slip so that the above contraction diminishes and a more typical deformation appears. THE shape change of bee and fee crystals deformed by compression or tension along [011] has been analyzed in some detail and shown to be responsible for the development of peculiar microstructures in [011] fiber textured polycrystals of these metals.1'3 This paper concerns the unusual shape change accompanying [011] compression of NaCl crystals. It is the direct outgrowth of an earlier investigation of the deformation of manganese sulfide inclusions in steel.3,4 In that investigation, cylindrical specimens of steel containing small oriented crystals of MnS were prepared by powder metallurgy and plastically compressed. The flow of the inclusions was determined relative to that of the steel by sectioning the composite and measuring the length-to-width ratio L/W of the inclusion and diameter-to-height D/H ratio of the steel cylinder on the plane of section. These L/W ratios, normalized by dividing by the initial LO/WO ratio of the inclusion, were compared with the normalized D/H ratio of the steel cylinder. Of particular interest here are the deformation characteristics of an inclusion oriented with [Oil] parallel to the compression axis. When measurements were made on sections parallel to the (100) plane of the inclusion, the L/IV ratios were only slightly in excess of unity, indicating a high apparent hardness of the [011] criented inclusion. However, measurements on a (011) plane of section resulted in L/W ratios which were much larger, Fig. 1. These observations prompted an analysis of the strains resulting from slip in an MnS crystal compressed along [011.]. CRYSTALLOGRAPHIC ANALYSIS Manganese sulfide has the NaCl crystal structure, and the predominant slip system is {110}(110). A secondary system, {111}(110), has also been reported.= {110}(110) Slip. When a crystal is subject to a uni-axial compressive stress 011 along [011], four slip systems, (101)[101.], (101)[101.], (110)[i10], and (110) [ 110], will be equally stressed with a shear stress t = 0.2 011 while the other two {110}( 110) systems will be unstressed. The normal strain En along any reference axis n resulting from slip is given by Schmid's law: en = S COS ?in COS in ?i 111 where ?in and +in are the angles between n and the i slip direction and n and the i slip plane normal, respectively, and where ?i is the shear strain on the i slip system, For the four active slip systems above, the cos ?in cos +in terms are all equal when the reference axes are the [011] compressive axis, [011] and [ 100]. Eq. [I.] therefore reduces to en - cos ?n cos +ny [2] where y =S?i for all slip systems. Substituting the appropriate angles, Eon = 0.25? 110 eon - 0.25y110 [3] €100 = -0.50y 110 The interesting feature of Eqs. [3] is that they predict that the strains in the [011] and [011] directions, resulting from {110}(110) slip, are equal and of the same sign. Thus when a crystal is compressed along [011], it will contract along the lateral [oil] direction

Jan 1, 1967

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965