Search Documents

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By M. Fig, J. Brune, C. Strebinger, G. Bogin, J. Grubb

"Although it is known that explosive gas zones can form and sustain combustion in a longwall coal mine gob, a complete account of the interaction of the methane flame and gob remains obscure. The goal of this study is to examine the impact of several gob parameters such as packing orientation and void spacing. The impact of ignition location is also detailed. A series of experiments with methane flames were performed in a horizontal cylindrical quartz reactor. The reactor was tested both empty and packed with an obstacle wall consisting of spherical glass beads to investigate the impact of various gob parameters. Results demonstrate that methane burning velocity is sensitive to all parameters investigated, and most sensitive to packing density and ignition location. INTRODUCTION The explosion at the Upper Big Branch Mine in 2010 and several other underground longwall coal mine fires and explosions show that explosive gases can mix with fresh ventilation air creating explosive gas zones (EGZs). Investigative reports of these fires have found that EGZs are able to move from the gob and into the active longwall face, endangering workers and equipment [1]. Currently, researchers at the Colorado School of Mines are using computation fluid dynamics (CFD) modeling to predict the location and movement of EGZs in the gob and along the longwall face [2,3]. It is the goal of this work to validate combustion models [4] that include interactions of the flame and the gob for future incorporation into ongoing CFD modeling of EGZs [2,3]. Throughout the years, there has been significant research investigating how flames interact with obstacles and propagate through porous media [4,5,7-11]. Since there is limited access to the gob in a longwall coal mine (Figure 1), the orientation and size of rocks and void spaces within the gob is unknown. Experiments of a simulated gob have been performed in a large scale flame tube in order to investigate the effect of scale (Figure 2) [4,5]. However, the variation in rock spacing, rock orientation, and void location makes it difficult to determine the impact of each of these parameters on methane flame dynamics. This study aims at gaining a stronger fundamental understanding of gob parameters such as spacing, orientation, and ignition location on methane flame propagation. The results from this study will provide a basis for experimentation in larger explosion vessels and will be used to validate methane combustion models for incorporation into longwall ventilation models of EGZ movement [2,3,4]. BACKGROUND Researchers have been studying flame propagation across obstacles and porous media for many years using various fuels and experimental setups [4,5,7-11]. Experiments have been performed in horizontal chambers with both ends open [7], horizontal chambers that are semi-open [4,11], horizontal chambers with both ends closed [8], and vertical arrangements [9,10]. Due to the variation in experimental setups and methods of characterizing flame dynamics such as flame speed, peak overpressure, or burning velocity it becomes difficult to directly compare results. Flame speed is a property of the mixture and refers to the speed of the unstretched flame front normal to the direction of propagation. This study characterizes the flame by its burning velocity, which is the difference between the flame speed and the speed of the unburned gases just ahead of the flame front. However, some references use the terms flame speed and burning velocity interchangeably. In this study, a semi-open quartz cylindrical reactor was used to determine methane burning velocity, which was used as a basis for comparison to determine the impact of obstacle configuration on methane flame dynamics. The quartz reactor also has the unique ability to allow for flame visualization. These features allow for faster combustion model validation [4]."

Jan 1, 2017

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

Batch grinding tests conducted on a gold ore indicated that gold is not randomly distributed within the size fractions of the ground ore. Since gold leaching performances were found to be dependent of the size of the gold carrying particles an integrated gold ore grinding-leaching simulator should incorporate a method to predict the gold size distribution of a ground ore. The paper describes the results obtained from batch grinding tests showing the non random distribution of gold within the size intervals of a ground ore and the initial developments of a grinding model to predict the gold size distribution in a batch grinding product.

Jan 1, 2011

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By J. B. Caine

THE investigation outlined in this paper was carried on at the plant of the Sawbrook Steel Castings Co., Lockland, Ohio. EFFECT OF TEMPERATURE In the study of the effect of temperature, heats were made with the Sawbrook company's standard practice, using multiple slags, the only difference' being that the heats were tapped at two temperatures; one group between 2960° and 3040°F and the other group between 3200° and 3250°F. Slags were weighed throughout the heat at each slag change and after the heat was poured. Only the significant slag weights, those of the total slag and the finishing slag, have been reported.

Jan 1, 1947

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By Lifent Li, Jhon Silva-Castro

Since millisecond-delay detonators were first introduced, at least two variables, among others, have been more closely considered when timing a mining blast: the accuracy and the precision of the initiation system. Currently, most mine blast design software has the capability to use the precision/accuracy of the firing system and display the overlap timing window between charges in any given time interval (8 ms, 3 ms, etc.). Despite these technological advances, there are still situations which result in the overlapping of charge timings. The consequences of overlapping charges involve flyrock events, fragmentation and diggability problems, and other inconvenient situations affecting the operation of the mine.

Jan 1, 2015

By F. S. LOTT

Publication of the Bureau of Mines annual surveys of the capacity of petroleum refineries in the United States was suspended after the entry of the United States into World War II . The last published survey was that of January 1 , 1941 , released in April 1941 as Information Circular 7161 . The purpose of this publication is to provide comparable information with respect to crude - oil and cracking capacity on January 1 , 1947. No attempt is made at this time to bridge the gap in annual statistical series from the date of the last published survey to the present one . However , complete summary tables will be included in the succeeding survey for January 1 , 1948 .

Mar 1, 1948

By Francisco Morganti

This report gives in the first part the metallurgical basics for the production of AHSS grades in integrated steel plants starting at the melt shop and ending at the annealing lines of the cold mill. The corresponding process and plant technologies in each production step with its specifics and rules are explained. In the second part by way of example the practical requirements for TRIP 780 steel grade are highlighted like a recipe for process control in the steel plant, hot and cold rolling mill, annealing line and finally skin pass mill. Measuring of mechanical technological properties on samples shows that the specifications according to DIN EN 10268 are fulfilled.

Oct 30, 2017

By P. R. Swann, R. M. Fisher, W. R. Duff

Observations by transmission electron microscoPy of the microstructures in quenched Fe-A1 alloys provide the basis for revision of the Fe-A1 phase diagram. The diagram is characterized by first-order transitions between the disordered ferromagnetic a! solid solution and the two ordered phases FeAl and Fe3Al. However, second-order transitions showing corre-luted fluctuations in the degree of order near the critical temperature occur between the paramagnetic a! and FeAl and the FeAl and FeAl phases. ELUCIDATION of the true nature of the Fe-A1 equilibrium diagram has proven to be an extremely challenging problem as evidenced by the fact that six quite different versions of the iron-rich portions have been published since 1958.&apos;-6 The most recent diagram shown in Fig. 1 was proposed by Rimlinger6 based on X-ray diffraction analysis and dilatometry. He shows the single-phase fields of the ordered phases of the types FeAl(L20) and Fe3A1(D03) and the disordered bcc Fe-A1 solid solution, a, separated from one another in every case by large two-phase regions. Thus, he implies that in Fe-A1 alloys ordering always occurs via a classical phase transition. In contrast to this view, theoretical studies3&apos;" have concluded that the transitions a — FeAl and FeAl — Fe3A1 should be second- or higher-order in character. A further revision of the Fe-A1 diagram of state is presented in Fig. 2 based on our previous8,9 and current observations by transmission electron microscopy of the microstructures found in quenched specimens. The average quenching rate was 50,000°C per sec and although this was sufficiently rapid to prevent Fe3A1-type ordering below -550°C it was not sufficient to suppress ordering of the type FeAl in the temperature range -650" to 800°C. However, ordering during the quench is easily recognized since the FeAl phase formed during holding at temperature rapidly develops large antiphase domains whereas FeAl formed during quenching has a very fine domain size, -50Å diam. Each symbol in Fig. 2 indicates the result of a micro-structural examination of specimens heat-treated (-1 hr) until equilibrium was established. The results will be discussed in the order of the points, A - Dl marked on both diagrams with reference to the phase fields, critical temperature, and "transition" ranges, respectively. The dark-field micrograph corresponding to point A is shown in Fig. 3 and was obtained using a 111 reflection of the Fe3A1 structure which reveals both a&apos;/4<111> and a&apos;/2<100> antiphase domain boundaries.10 The structure observed in this specimen is typical of single-phase Fe3A1 and shows no evidence for FeAl or any other additional phase. The dark-field micrograph shown in Fig. 4 corresponds to point B on the two diagrams. It was taken with a 100 FeAl reflection which reveals a/2(111) domains and exhibits the typical structure of single-

Jan 1, 1970

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,&apos; on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

By Zay Jeffries

A SURVEY of rare metals and minerals for the past year places uranium as one of two partners, the other being the neutron, in what historians will probably say is the greatest discovery in physics at least during the year and probably for a consider- ably longer period. The uranium atom has been made to divide into parts somewhat after the style of reproduction of the amoeba. When an amoeba divides into two parts, however, it produces two amoebae substantially alike and each substantially like the parent: furthermore, there is no considerable change of energy when this happens. When the uranium atom divides it yields other atoms such as barium and krypton with the complete destruction of the original uranium atom but with the liberation of a tremendous amount of energy. This will be discussed more at length later.

Jan 1, 1940

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By Jeff Easton, J Johnson, D. Foot

The Mina Santa Rosa mine in Panama was the victim of a mine closure 24 years ago that left the community in dire straits. The mine showed the potential resources of greater than 1M ounces of gold and 4.5M ounces of silver. Veragold Mining Company decided to reopen the mine and address all the issues that were involved in the startup of an historic mine. This paper provides methods to restore the community trust, provide a transparent process, and develop an environmentally sound flowsheet. Immense scrutiny surrounded the Tailings Storage Facility, and the company developed a plan focused on paste thickening and surface stacking to eliminate the need for a conventional tailings’ facility. Paste thickener principles and benefits are also provided.

Feb 1, 2024

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

Edgar Hall, Silverspur, Queensland, Australia (communication to the Secretary*):—Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the eide of freedom among the&apos; younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms mentioned have suffered by their secrecy is their own business—I hold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to he proved conclusively by Dr. Douglas&apos;s own writings. In his paper on The Copper Situation,&apos; Dr. Douglas says : "In comparing iron and copper mining,...it must be remembered that 2 tons of average iron ore from the most prolific source now available ... will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year&apos;s production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-orc would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Jan 1, 1909