Search Documents

By Bian Xue, Wu Wenyuan

In order to recycle the iron and rare earth from the Baotou tailings, a roasting method was developed involving the addition of C, Ca(OH)2, and NaOH, designed to both decompose the rare earth minerals and convert haematite into magnetite and allow its recovery. The effect of various parameters such as roasting temperature, roasting time, C addition, Ca(OH)2 addition, and NaOH addition on the reduction ratio of haematite (iron sesquioxide) and decomposition ratio of rare earth were investigated. The results showed that the reduction ratio of haematite and the decomposition ratio of rare earth could be as high as 85% and 95% respectively when the roasting temperature was 650°C, roasting time was 60 min, Ca(OH)2 addition was 4%, NaOH addition was 3%, and C addition was 1.5%.

Jan 1, 2014

By S. Kmet, A. Nguyen-Van, H. J. Schulze

The P/B collision and attachment interactions in fine particle flotation have been quantitatively analyzed. New models for attachment probability and kinetics of ‘true flotation’ have been developed. The results are given for both a single bubble and a bubble swarm. The mechanism of the attachment event is also examined. It is shown that (i) impact collision mechanism and rolling mechanism can be ignored in actual fine particle flotation and sliding mechanism is of importance for attachment of particle onto the bubble surface (ii) the attachment probability of fine particles is independent of bubble size and determined by the kinetic measure induction time of hydrophobicity. The theoretical predictions are also compared with the experimental data.

Jan 1, 1995

CONTENTS PAGE PEIRCE, CARL-Making Rimmed Steel. Discussed by L. F. Reinartz. H. D. Hibbard, C. L. Kinney, Jr., A. H. Woodward, V. B. Buck, A. L. Feild, J. V. W. Reynders 1 SCHROEDER, F. W., and LARSEN, B. M.-Progress Report of the Effect of the Open-hearth Process on Refractories. Discussed by D. A. Lyon 12 KEATS, J. L., and HERTY, C. H.-Elimination of Metalloids in the Basic Open-hearth Process. Discussed by J. V. W. Reynders 14 Making Rimmed Steel Discussion of paper by CARL PEIRCE, presented at the New York fleeting and issued, as Paper No. 1563-C, with MINING AND METALLURGY, March, 1926. L. F. REINARTZ, Middletown, Ohio.-Mr. Carl Peirce has presented a valuable paper on a subject that has been very widely discussed in recent years, especially since the demand for high finish, deep drawing and other grades of sheet steel in the lower carbon ranges has become an important factor in the steel business. Steel of this analysis has been produced for many years, but the product for which it was made did not require the extra care in the steel plant that it does today. It must now be worked down into thin sheets for special purposes and undergo many severe finishing processes both in the steel mill and in the fabricating plants. Mr. Peirce's paper has outlined in a concise and logical manner the steps which must be taken in manufacturing such steels. The secret of successs is attention to details of well known steel practices. I agree with him that quality steels of this class cannot normally be made out of inferior raw materials. Scrap should be clean and if possible not too variable in analysis. Galvanized scrap or babbit are particularly objectionable. Scrap should be in such physical condition that undue delays are not encountered in charging the furnace. Limestone should preferably contain over 95 per cent. available calcium carbonate, and be free from clay or other foreign substances. Almost universal practice shows that 10 per cent. limestone is required for proper slag volumes to protect the metal from over oxidation. The use of 8 per cent. limestone makes the operation less fool-proof.

Jan 4, 1926

By J. Engelbrecht

Understanding the deportment of minerals in size fractions has already led to improvements in the flow sheets for platinum minerals beneficiation. There are, however, more potential changes in the flow sheets that may improve the recovery of platinum group metals or reduce the costs of beneficiation before refining. Based on known technology of pre-concentration, milling, gravity concentration, flotation, and magnetic separation a number of potential alterations or additions can be considered and motivated based on the mineral deportment in size fractions.

Jan 1, 2012

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

Although the Diamond that is cut and polished and made up into an article of jewellery, is so well known, there are, comparatively speaking, very few outside the industry who know this beautiful crystal in the crude state, as turned out ofNature's laboratory, and the means employed in winning this precious stone.This article is written with the endeavour to give the reader some idea of the geological formations in which the Diamond occurs, and as it is reported that Diamonds have been found in Western Australia, as well as in other parts of the Australian Colonies, a few hints as to the means employed in working the ground in South Africa may be of use to those intending to prqsecute the search in this country. The general geological formation of the South African Diamond Fields is Lacustrine shales and sandstones, intersected by dykes of various eruptive rocks, varying considerably in their character. and in places vesicular in texture, the vesicules being more or less filled in with zeolites by permeating waters.

By S. M. Spottiswoode, A. J. Jager, N. C. Gay, J. A. Ryder

The South African mining industry is at present planning to extract orebodies at depths of up to 4 km. To do this cost effectively and, at the same time, ensure safe working conditions for mining, the personnel will require both the development of new strategies and the implementation of current rock-engineering technological developments on a wide scale. This paper covers most of the technological developments likely to be required for mining at very high stresses, but it is clear that improved regional support systems will need to be developed to ensure defective stability of the rockmass during mining operations. Similarly, it is clear that improved strategies for mining in large-scale geologically disturbed areas, where slip on faults or dykes can result in wide-spread rockburst damage, will have to be addressed

Jan 1, 1995

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By Leon del Valle, Joe Phillips

First, I want to thank my co-author, Leon del Valle for his help and collaboration in the preparation of this paper, and also ORICA S.S. our explosive supplier and contractor at the Refugio mine site for their collaboration. The Southern Andes Mountains present a number of challenges for mining operations, and associated blasting operations. This region of the world, in Peru, Bolivis, Chile and Argentina is an area of rapid growth in precious and base metal mining, and will continue to be a large growth area for explosives products and services. This paper will attemp to discuss some of the special considerations encountered in operating a safe and effective blasting program at high elevation and under extreme weather conditions, as well as outlining a recent improvement in blasting techniques at the Refugio gold mine in northern Chile. This paper is presented from a mine operator's perspective, which may be a bit of a disappointment for some of you interested in a detailed technical review of our program. It willl, however, provide an insight in how in-pit blasting techniques tie into the metallurgical processes at a modern precious metal mine and thereby become a key elemnet in its success.

Jan 1, 2000

By J. D. Miller

Contact time during bubble/particle collision is calculated by taking into considera¬tion the effect of bubble and particle motion, buoyant force, bubble size, and particle size and specific gravity density for different cases of collision. From this motion analysis approach for the prediction of contact times and from bubble attachment-time measurements,, fundamental aspects of flotation such as flotability, kinetics, and separation can be explained and are discussed with respect to the effects of bubble/particle motion, bubble size, particle size, and attachment time.

Jan 1, 1987

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

By Wilson G. L, Lord J. H

A detailed analysis of faulting indicatcs that blocks of "greenstone" have been thrust beneath the southern end of the Mt. Isa orebodies.This "greenstone" basement is considered to be a major structural control in the localization of these orebodies.INTRODUCTIONThis paper is based on exploration carried out by Mining Corporation (Aust.) N.L. from 1956 to 1960 in the area immediately south of Mt. Isa, Queensland. During this period over 20,000 ft of diamond drilling was completed together with costeaning and geochemical exploration.Early in 1959, it became apparent that diamond drill information could not be correlated with the current geological concepts of this area and a detailed geological appraisal became necessary. In all, sixty square miles were mapped at a scale of 1 in. to 500 ft, using enlarged aerial photographs. All drill core was logged and sections re-interpreted.Professor K. C. Dunham of the University of Durham consulted on this project and contributed through valuable discussion. Dr. A. Day of the University of Sydney carried out a gravity survey in February 1960 and Dr. H. Wilshire of the same University undertook microscopic examination of rocks from the area. Certain sections of the area were investigated geochemically by Mr. K. K. Hughes of New Consolidated Gold Fields (Asia) Pty. Limited in 1960.In outlining a theory of ore genesis in the area the writers have drawn heavily on the invaluable data published by many previous workers on the Mt. Isa field, in particular...

Jan 1, 1963

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By Frank Arthur Forward

FRANK ARTHUR FORWARD was born in Ottawa and attended the University of Toronto, where he received a B.A.Sc. in chemical engineering in 1924. From 1924 to 1929, he was a smelter operator and research metallurgist with the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. Moving to Australia in 1929, he was assistant smelter superintendent, Mount Isa Mines Ltd., Queensland, until 1934, when he returned to Canada, spend-ing one year as metallurgist with B.C.

Jan 1, 1970

The Telfer main dome open pit is operated by Newcrest Mining Limited at a current production rate of 50 Mt/a from a pit dimension compromising 2 km strike length, 1 km width and 250 m depth. As part of the refeasibility of the Telfer operation undertaken early this decade, Newcrest identified that an underground sublevel cave (SLC) operation along with an increased scale of open pit would support a new plant targeting the processing of gold and copper ore at 17 Mt/a rates. The SLC was initiated in late 2006 and broke into the open pit in late 2009. This situation is unique across the mining industry where a cave breakthrough was planned and occurred within an active large open pit operation. The SLC broke though into the west side of the Main Dome open pit into a specially prepared bench that was left at the 5384 RL of cut-back stage 3. A main haulage ramp is within 100 m from the edge of the cave breakthrough zone and this ramp passes down to the active levels which are progressing toward the 5200 RL. This paper presents insight into the mine planning and risk management associated with continued operation of the open pit operation while an active SLC breaks through. The cave breakthrough presents unique areas for risk management as there is potential for rapid propagation and subsidence. To support the undertaking, mine design and major hazard management planning has been carried out. Focus areas include; dual ramp system design, preloading the breakthrough area, monitoring of cave propagation and air gap using a seismic system and deep hole extensometers, wall stability and subsidence monitoring using radar and prism systems, and key trigger and response planning.

May 1, 2010