Search Documents

By V. Yahorava

Efficient recovery of precious metals from process solutions is essential for improving process economics. Traditionally, precious metals are relatively effectively recovered from waste streams via precipitation or cementation. However, these approaches have a number of drawbacks, including poor water balance, creation of environmentally unfriendly waste streams, and losses of precious metals. Ion exchange technology is an alternative for the recovery of precious metals from waste or low-grade streams. This technology allows the recovery of the precious metals to extremely low levels (micrograms per litre) with relatively high upgrade ratios from the solution onto the resin without major water balance concerns, while the impact on the environment could be minimized or avoided. Research was conducted on the recovery of platinum group metals and gold from different low-grade and waste streams from one of the precious metals refineries in South Africa by means of ion exchange. Various functionalities and matrices (granular and fibrous) of ion exchange materials were evaluated. The results from these studies indicated that in some cases ion exchange could be very effective for the recovery of precious metals, and that the PGM concentration could be reduced to < 1 mg/L. The upgrading ratios of the various PGMs onto the specific fibres were relatively high for the specific streams evaluated, which might in some cases justify incineration of the loaded material instead of stripping and recycling the adsorbent. The cost of direct incineration for one of the waste streams tested would be less than 1% of the value of the PGMs recovered. However, the adsorbent has to be carefully selected and the process design optimized for each specific stream.

Jan 1, 2014

By J. J. Crowhurst

The modem open pit-heap leach operation by Pegasus Gold Ltd. at Zortman and Landusky in Phillips County, Montana, is a new chapter in the mining of gold in these districts. The discovery of bulk tonnage ore bodies and their development and ultimate production was based on a long history of mining and exploration in that part of Montana. Gold was originally discovered in the Little Rocky Mountains as placer deposits by Pike Landusky and Lou Myers. This discovery in the 1880s was not significant, but Pike Landusky continued prospecting for lode deposits, and he eventually located the Gold Bug and Little Ben, two of the larger Au-Ag producers in the district. Eventually two camps, Landusky and Zortman, grew in the LittleRocky Mountains. By the time Landusky was killed in 1894 by Kid Curry, the district was still a discontinuous small producer. Steady production commenced in 1907 with the organization of the August Gold Mining Co. Eventually high grade ores on specific veins were exhausted by selective underground mining and the district was idle by May 1942. After World War II in the early 1950s. E.A. Scholz tried to continue selective underground mining, but he realized the stockworks surrounding the larger veins constituted bulk tonnage targets. Ultimately in the 1976- 1979 period he organized two exploration efforts, one each for the Landusky and Zortman areas, and brought these into production as the Argo and Pegasus gold mines. By the time of his death, Apr. 8, 1980, both operations were producing gold. Later the two companies were merged as Pegasus Gold Ltd. Upon the death of Scholz, V.F. Hollister continued as the geological consultant, Ed Roper was engaged as general manager, and J. J. Crowhurst was given the responsibility of executive vice president. The discovery of open pittable ores and the application of heap leach technology was important in the development of mining. Both contributed to the low cost operation that continues to this day. The attached article by L.M. Rogers, then chief geologist, and M.S. Enders, his assistant, describes the geology of the deposit. It was presented at the Northwest Mining Association meeting in 1982.

Jan 1, 1990

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two&#160;projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By A. W. Hahn

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it becomes important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determining whether the individual minerals were in the so-called "free" state.

Jan 1, 1929

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner&apos;s interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem&apos; has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.&apos; show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.&apos; The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,&apos; P. H. Keck,&apos; and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of the Interior, as of January 1, 1934, there were 591 completed refineries in the United States, an increase of 86 ever the total reported at the beginning of 1933 and the largest total ever recorded. It should be noted that the 1934 total, although large, probably does not include more than half of the "pot-still" plants of 1 barrel to 50 barrels daily capacity which have sprung up within the last 2 or 3 years and about which very little information is available. However, the combined operations of these snail refineries are of negligible importance as altogether they refine less crude than one plant of average size. Of the completed plants, 454 were operating on January 1, 1934 and 137 were shut down. In addition, 13 refineries were under construction on January 1, 1934. Compared with the previous year these data indicate a marked increase in the number of operating plants, little change in the number of inoperative plants, but a decline in&apos; the number being built. The material gain in the number of operating plants resulted primarily from the construction off approximately 25 refineries, averaging about 100 barrels capacity in the Kooky Mountain district, as well as from the addition of about 20 plants in the East Texas field.

Jan 1, 1934

By Rees D. Rawlings, C. W. A. Newey

The aging characteristics of an Fe-11 at. pct Mo alloy have been studied by means of light metallography together with density, Young&apos;s modulus, and hardness measurements. The results were consistent with the precipitation of a single intermetallic compound during aging; overaging was slow relative to that in other iron-based binary alloys. The solution treatment temperature had a small effect on the rate of hardening whereas deformation prior to aging had a marked effect on both the rate of hardening and the peak hardness. The density data indicate that the compound precipitated is Fe3MO2 and not the Laves phase Fe2Mo. Analysis of the modulus and density results gave values for the time exponent for precipitate growth of approximately 1.0 and 1.5 for the alloy aged with and without prior deformation, respectively. DETAILED studies of precipitation hardening in bcc matrices have been confined largely to the effects of carbides and nitrides. In view of this and the growing technological interest in intermetallic compound strengthening, e.g., in maraging steels, a study of precipitation in iron-based alloys with a low interstitial content has been undertaken. This paper is concerned with the aging behavior of an Fe-11 at. pct Mo alloy; the mechanical behavior of the alloy will be reported later. The early work of sykes on Fe-Mo alloys showed that precipitation of the intermetallic compound was accompanied by an increase in hardness and a decrease in volume of the material. More recent surveys of the strengthening associated with precipitation have been made3-5 and, in particular, Elsen and wassermann4 showed that deformation prior to aging increased the rate of hardening. These latter workers also followed the precipitation process by means of dilatometry, electrical resistivity, and lattice parameter measurements. Their results confirmed that there is a decrease in volume on aging. Except for the work of Hornbogen on an Fe-20 at. pct Mo alloy, neither clustering nor the precipitation of a nonequilibrium phase has been observed in Fe-Mo alloys. Studies of alloys of lower molybdenum content475 indicate that the equilibrium intermetallic compound is precipitated during aging. However, there is some doubt concerning the nature of the equilibrium precipitate phase. According to the phase diagram constructed by Hansen,8 the phase should be precipitated. This phase has a rhombohedra1 crystal structure which is characterized by the formula Fe706,&apos; although the composition of the molybdenum-rich boundary corresponds approximately to Fe3Mo2. The version of the diagram proposed by Sinha, Buckley, and Hume-Rother indicates that the A phase, a Laves phase Fe2Mo, should be precipitated. Their observation of a Laves phase supports the earlier findings of Bechtoldt and Vacher,13 although, in a recent study of the system by means of diffusion couples, Rawlings and Newey did not detect the phase. The work presented here describes the effect of solution-treatment temperature, aging temperature, and prior deformation on the aging characteristics of the alloy as revealed by light metallography together with hardness, density, and Young&apos;s modulus measurements. In addition the density data are used in an attempt to determine the compound precipitated during aging. EXPERIMENTAL PROCEDURE A 29-kg ingot of the alloy was cast at R.A.R.D.E., Fort Halstead, from deoxidized, Japanese electrolytic iron and sintered molybdenum. The ingot was homogenized for 6 hr at 1473°K and then worked, with intermediate anneals, into 6- and 16-mm-diam rods and 6-mm plate. Chemical analysis of the alloy gave, wt pct: Mo, 17.5 (11 at. pct); C, 0.003; Si, 0.002; S, 0.005; P, <0.002; and02, 0.0098. Solution treatments were carried out under a dynamic argon atmosphere in a vertical, "crusilite" element, furnace which had a facility for rapid quenching into iced water. Except for the study of the effect of solution treatment temperature, all specimens were solution-treated at 1573" * 2°K for 1 hr. Salt baths were used for the aging treatments. Specimens for hardness, density, and Young&apos;s modulus measurements were produced, after heat treatment, from the stock rod or bar using a precision silicon carbide slitting wheel. As described later, the quenching treatment produced local plastic strain in the stock material; consequently, care was taken to ensure that the specimens were not prepared from these regions. Those specimens used in the studies of the effects of prior deformation on the aging behavior were strained in compression in a Denison universal testing machine. Specimens for light metallographic observations were mechanically polished on successively finer grades of diamond paste down to and then etched in either alcoholic ferric chloride or in a 2 pct nital solution. Vickers diamond pyramid hardness data were obtained using a 30-kg load. At least five impressions were averaged for each determination. Density measurements were made using a displacement technique in which each specimen was weighed in air and in dibromoethane at 296°K. The specimens were cylindrical and weighed 3 to 4 g; all weighings were made on a balance reading to 1 x 10"5 g. For each specimen the mean value of five weighings was used to calculate the density. The density of the dibromoethane was determined using the displacement procedure and a standard nickel specimen. The error in an absolute density value was estimated to be HI.01 pct. To obtain the density as a function of aging time a single specimen was used and the density meas-

Jan 1, 1969

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,&apos; the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,&apos; the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.&apos; Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier&apos;s equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier&apos;s equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

By O. P. Quist, S. H. Carpenter

The internal friction of single-crystal LiF has been investigated as a function of crystal orientation, while simultaneously applying a static compressive load. Three different crystal orientations were used, these being samples with the (100), (110), and (111) directions along the sample length. Results show the internal friction measured to be similar in appearance but different in magnitude for the (100) and (110) samples. With both orientations, application of a static stress caused an increase in the amplitude-independent damping, which recovered with time. The amplitude-dependent damping was found to first decrease with load up to the yield stress and then increase rapidly. Samples of the (111) orientation were found to have no measurable internal friction even when loaded up to 3.0 kg per sq mm. These results are discussed in terms of current theories of internal friction in ionic crystals. This paper presents the results of an investigation of the dislocation mobility and dislocation motion in high-purity single-crystal LiF at applied stress levels up to the yield stress. Internal friction measurements of the dislocation damping while simultaneously applying a static compressive load was the experimental technique used. LiF crystals much prefer to slip on the (110) set of slip planes. However, with a suitable stress distribution they can be forced to slip on the {100} set of slip planes.&apos; For both sets of slip planes the slip direction is the same, namely (110). The object of this investigation was to try and learn more about the dynamical properties of dislocations on the different slip systems in LiF crystals. EXPERIMENTAL PROCEDURE Dislocation damping was measured, in terms of the log decrement, using a five-component marx2 composite piezoelectric oscillator. The apparatus used allows one to measure the dislocation damping while simultaneously applying a static compressive load on the sample. A schematic of the apparatus used is shown in Fig. 1 and a complete discussion of its construction and operation is given elsewhere.3 All measurements were made at room temperature with a longitudinal resonant frequency of approximately 50 kc per sec. Damping measurements were made using longitudinal vibrations with strain amplitudes from up to 10. Static loads up to 3.0 kg per sq mm were applied to the sample while the damping was being measured. Samples used in this investigation were high-purity single crystals of LiF purchased from the Harshaw Chemical Co. All samples were approximately of an in. square and were hand-ground in length to one-half wavelength to match the resonant frequency of the driver and gage quartz crystals. Samples of three different crystallographic orientations were used, namely, crystals with the (loo), (110), and (111) direction parallel to their length. The magnitude of the damping is a direct measure of the area on the slip planes swept out by dislocations during a complete oscillatory cycle. With a sample of the (100) orientation the maximum applied shear stress, due to longitudinal vibrations, is on the (110) slip planes with zero shear stress on the (100) slip planes. Thus, damping measured from a (100) sample is due entirely to dislocation motion taking place on the (110) set of slip planes. Similarly, for a sample of the (111) orientation there is zero shear stress on the (110) set of slip planes and the damping measured from a sample of this orientation is due entirely to dislocation motion on the (100) set of slip planes. Samples of the (110) orientation will have a component of shear stress on both sets of slip planes and

Jan 1, 1969

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler&apos;s saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By C. O’Donova, E. Adam, L. A. Torres-Cruz

High-profile failures of tailings dams illustrate the significant safety challenge they pose. The decant pond of such facilities plays an important role in their mechanical stability. This study investigates the feasibility of using public multispectral data collected by the Sentinel-2 satellite mission to monitor the area of the decant pond. The Sentinel-2 mission has a revisit time of 5 days and the data used herein has a spatial resolution of 10 m/pixel. We considered two water-detection metrics: the normalized difference water index (NDWI) and the near-infrared (NIR) reflectance. Implementation of the method at a South African platinum tailings dam illustrates the capabilities and limitations. Public, sub-metre resolution true-colour imagery served as validation data. There is good agreement between pond area measurements based on Sentinel-2 and the validation imagery. These results suggest the feasibility of using Sentinel-2 data to supplement the monitoring of the decant pond.

Apr 2, 2022

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of &gt;2000 people from their communities, the high average annual rainfall (&gt;2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to &gt;2000 m within 20 km of the coast, and to &gt;3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By J. D. Lindner, Gene E. Roark

Waterflooding operations in the Langston-Kleiner field. Young County, Tex., are described. Widespread application of formation fracturing has been practiced in both producing and injection wells. Field performance data arc cited which indicate than no detrimental effect on sweep efficiencies and that probable benefits in imectivily have resulted from the fracture treatments. I N T R O D U C I O N This paper is a report on a waterflood operation which is being carried out in the Lanpston-Kleiner field located in Young County, Tex. The oil reservoir aflected by this flood operation occurs in a Strawn sand member at an approximate depth of 3.550 ft subsurl&apos;ace. The operators of&apos; the project are Kleiner Estate. Turncr. Fiske. and West who are hereinafter collectively referred to as the Operators. Although the operation is unusual in several respects, the distinctive feature of this flood has been the widespread application of hydraulic formation fracturing treatments as a means to improve productivity and injectivity of the wells. It shall he the purpose of this paper to present basic information regarding the reservoir characteristics. op- craling practices, and waterflood behavior so that conclusions may be drawn concerning the effects which the fracture treatments have had on the performance of this water flood to datc. DEVELOP MENT Development of the 3,550 ft Strawn sand reservoir occurred during 1951 and 1952. The early development occurred on the Langston and Davis leases which arc in the northern region of the Operators&apos; holdings and the wells were drilled on 20-acre proration units according to the field rules. However, studies of the economics of this program. coupled with the decision to proceed with pressure maintenance by water injection. resulted in the adoption of wider spacing in the later stages of development. This variation in spacing is apparent upon inspection of Fig. I upon which only the 3,550-ft Strawn sand producing and injection wells have been located on the Operators&apos; properties. The development to the north of the operators leases is Ihe Garvey Strawn field and that to the south is the Taylor Strawn field. It wits determined that unitization of the leases to he involved in the waterflood program was not feasihle. Consequently. a system of offset injection wells, or lease line injection wells, was adopted from place to place as required to protect correlative rights in the program. This resulted in a dispersed array of injection and producing wells with relatively close proximity of wells along lease line areas and wider spacing toward

Jan 1, 1956

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934