Search Documents

By A. Keith Brewer

RECENT advances in the fields of chemistry, biology, and metallurgy have confronted the analytical chemist with an entirely new set of problems. Development of plastics and synthetics has brought about a need, not only for adequate methods for their analysis but also for the various raw materials entering into their manufacture. The remarkable advance made in biochemical and agricultural research resulting from the use of isotopes as tracers or "tagged atoms" has established the necessity for the development of methods for the concentration of natural isotopes and for a means for their analysis. Similarly the advent of new and complex alloys calls for accurate analytical methods. Fortunately the analytical chemist has been able to meet some of these new demands by adapting to his purposes an instrument which has long been the most exclusive toy of the physicists. Solubility and the chemical properties of the atoms, which have always served as the basis for chemical analysis, do not enter into this new technique. Instead, momentum, defined as mass times velocity, is utilized as the means for the separation of atoms or mass groups.

Jan 1, 1946

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

By Szilvia Szabo, Jozsef Paulovics, Ljudmilla Bokanyi

"Waste recycling is one of the most important challenges of the XXI century. The recycling of wastes is closely related to and bases on the mineral processing. Many mineral processing techniques and equipment are applied in this field. The principles of the characterisation of wastes and design of technologies is rather similar to the classic mineral processing. Nevertheless, the diversity of the wastes and their complex composition and properties, as well as their environmental impact requires a special approach.Solar elements have sandwich structure of glass substrate and cover, as well as a very thin semiconductor layer. CdTe semi-conductor can be recycled by flotation. Within the RESOLVED (LIFE European Framework) R&D project on the recycling of solar elements the surface properties of pure CdTe semiconductor and pure glass were investigated by the measurements of zeta-potential using Zeta PALS Brookhaven instrument at University of Miskolc. Applied surfactants were: potassium ethyl xanthate; the anionic oxhydryl Aero Promoter 825 or Flotinor SM 35; the cationic Armoflote 43 or Armoflote 64, as well as Hostaflot LET (dithiophosphoric acid diethyl ester) and Hostaflot M91 (mercaptobenothiazole). The tested electrolyte was sodium-silicate. Zeta-measurements were carried out in full pH-range. Interfacial interactions were detected and interpreted. The basic results were verified by the flotation kinetic tests.Finally, the flotation technological experiments were carried out at a semi-technical scale using the real obsolete solar elements. The particle size at the liberation degree of 98% was as fine as below 5 µm. A special flotation cell providing the generation and distribution of very fine air bubbles was built. The pre-concentrate for the manufacturing of the test solar module was performed and transported to the BAM Institute (Berlin), the principal co-ordinator of the Project, and then further to the First Solar (USA) where a new panel was manufactured using recycled semi-conductor."

Jan 1, 2016

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

Oct 1, 2001

By A S. Lund

Optimisation of the underground mining production process benefits from informed decision making during the process of explosive rock fragmentation. Selection of the most appropriate bulk explosive products for underground production blasting is an area of endeavour that offers significant economic upside if correctly and thoroughly undertaken. The explosive selection process is facilitated by a clear understanding of:the physical and detonic properties of the alternative explosive options available; the response of different rock masses to these different explosive options; and the importance of maintaining a clear focus on desirable blast outcomes in order to enhance value creation aspects of the mining production process. The level of understanding of these issues is raised through the application of measurement and modelling technology, quantifying the effects of blast design (and implementation) on process outcomes. Homestake Darlot and DynoConsult applied a range of dynamic blast measurement and outcome modelling techniques in order to explore the relationship between rock properties, explosive properties and mining process efficiencies. A campaign of vibration and explosive Velocity of Detonation (VoD) measurement produced feed data for use in vibration and fragmentation modelling during the extraction of one of the major stoping blocks at Darlot Gold Mine. The paper describes the use of these tools and discusses the understanding gained concerning the limitations and capabilities of, and the reconciliation between, a selection of analysis and modelling approaches.

Jan 1, 2001

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces, The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as S02 in the flash furnace. Preliminary experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By S. Kwon, J. W. Wilson

"In salt and potash mines, the time-dependent deformation mechanism should be clearly understood based on in situ measurements to predict the performance of a mining design. In this study, in situ deformation measurements from the Waste Isolation Pilot Plant (WIPP) and other salt and potash mines were used to determine the transition time from the primary to the secondary creep stage and to investigate the influence of adjacent excavations such as a nearby tunnel excavation, panel excavation and/or pillar extraction on rock deformation. IntroductionThe deformational behaviour of underground excavations in salt and potash mines is complex due to the time-dependency of the rocks. When the material properties are determined from laboratory tests, they should be carefully applied to in situ conditions, because in situ conditions are completely different from laboratory conditions. For instance, in situ deformation measurements show that the deformation rate decreases with time similar to those observed in the laboratory during the early stages. However, the rapid decrease of deformation rate does not come from the microscopic strain hardening effect observed in laboratory tests, but mainly from stress relief around the opening after its excavation (Baar, 1977). It is, therefore, recommended to undertake in situ measurements and use them to understand the deformation mechanism.Even though in situ measurements are widely accepted as important information for understanding the deformation mechanism of salt and potash (Barr, 1971; Kovari and Amstad, 1993), not many publications have focused on the fundamentals of data measurement, the application of the measured data, and the development of data analysis techniques. Recently, several new techniques for better understanding the deformation mechanism of rock salt have been developed that are based on in situ measurements. Kwon and Miller (1995) developed a new technique for describing the actual deformational behaviour of an underground excavation in rock salt. The migration of “zero strain boundary,” which represents a no movement boundary around an underground excavation, could be calculated by the technique developed by Kwon and Miller (1996). Kwon and Wilson (1997, 1998) applied neural network techniques to in situ deformation measurements to predict the deformational behaviour of the underground excavations at the Waste Isolation Pilot Plant (WIPP) located in the United States.In this study, in situ deformation measurementsfrom the WIPP site and other salt and potash mines in the United States were extensively analyzed to understand the deformation mechanism of the underground excavations in the rock mass."

Jan 1, 2002

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

By Yunxing Cao, Xinsheng Zhang, Bingbing Meng, Shuaifang Guo, Li Wang, Junsheng Zhang

During the initial process of mining a longwall working face, it is often found that the roof will not collapse readily, which increases the risk of later roof collapse disasters. Explosive and hydraulic fracturing are common roof weakening techniques; however, they have certain limitations. In the present study, CO2 fracturing was used for roof weakening during the initial mining phase in the Changcun coal mine, China, which is a novel strategy. First, by analyzing the lithological characteristics of the working face and applying combined beam theory, the breaking spans of the top coal, immediate roof, and main roof were determined before weakening. An F-35 CO2 fracturing device with a rated pressure of 270 MPa was used, which provides fracturing energy equivalent to 0.968 kg of TNT. The fracture radius of the main roof was studied by ANSYS/ LS-DYNA combined with the hanging roof-breaking theory to determine the optimal layout of CO2 fracturing drills. The results show that the breaking spans of the top coal, immediate roof, and main roof were reduced by 3.99 m, 7.66 m, and 22.03 m, respectively. The main roof collapsed as the working face advanced, eliminating the chance of later roof collapse disasters. Compared with hydraulic fracturing and explosives, CO2 fracturing is safer and more practical, giving it significant application potential.

Nov 23, 2023

By P. Shahinian, M. R. Achter

In a comparison of the creep -rupture properties of nickel in air arid in vacuum there is a reversal in relative strengths with variations in stress. At low stresses the properties are better in air while at high stresses they are better in vacuum. In the early stages of creep in a high stress test the specimen in air nzay have the lower creep rate but the one in vacuum is creeping at a lower rate in the later stages. A mechanism, involving two competing processes in terms of oxidation strengthening and weakening by surface-energy reduction, is proposed to explain these reversals. It had generally been assumed that, relative to their properties in air, the high-temperature strengths of metals would be increased in an inert atmosphere as a result of the elimination of the deteriorating effects of oxidation. However, several recent investigations have shown that the creep strength may be greater in air than in nonoxidizing gases. Pickus and Parker1 found that the creep rate of nickel was lower in air than in hydrogen or nitrogen. Internal oxidation was mentioned by Shepard and Schalliol as a possible cause for the longer creep life of Hastelloy C in air than in vacuum or helium. Sweetland and Parker, who observed lower creep rates for aluminum and copper in air than in helium, discuss the possible applicability of the dislocation-barrier mechanism to explain their results. Surface oxide layers may interfere with the escape of dislocations through the surface or with their generation there. In addition to showing the strengthening in air of low-alloy and stainless steel, and nickel and cobalt-base alloys, shahinian4 presented notch-effect data which indicate the role of stress concentrations; alloys of relatively low ductility were more sensitive to atmosphere strengthening when notched specimens were used. Although Bleakney's copper wires had a lower reduction of area in air than in vacuum, it is difficult to interpret his results in terms of strength changes since the stresses employed were not measured. In contrast to these data showing the strengthening in air, a number of investigations, most at relatively low temperatures, have demonstrated that the environment may cause a decrease in strength. These results are generally explained in terms of the effect of environment on surface energy. In a review of the subject, Benedicks and Harden use the concept of atomic bonding to explain how the adsorption of impurities would decrease the energy of a clean surface. A decrease in surface energy would facilitate the propagation of cracks or extension of the surface. Use of this mechanism is made by sato7 to explain the weakening of steel specimens bent in various liquids, by Potek and Shcheglakovs for the reduction of fracture strength of steel in molten metal, and by Benedicks and Harden for the reduction of strength of a variety of materials in a number of liquids. A similar explanation might be used for the results of Forestier and Clauss. The fracture stress of fine wires pulled in a variety of gases, including air, is lower than in vacuum. They attributed their results to the "tendency" for the gases to condense on the metal surface. That the strength of metals is affected by the type of gas in which the test is conducted has been demonstrated convincingly; the mechanism of the effect, however, is still uncertain. This investigation represents one in a series to explore the influence of variations in alloy composition and test conditions on the atmosphere effect in the expectation that the results would afford an insight into the processes taking place. To determine the effect of specimen composition, the present investigation was conducted

Jan 1, 1960

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By G. A. Koenig, Moritz Stockder

Locality and Geological Occurrence. The Alpine region of Southwest Colorado, comprising the San Juan and Uncompaghre Mountains, is composed of a deeply eroded sheet of acid eruptive rocks, overlying in part gneissic sehists, and in part limestones and sandstones, including portions of the Silurian, Devonian, and Carboniferous systems. The section is clearly and beautifully exposed along the Uncompaghre River from its headwaters to its exit from the mountains. The river's course from the town of Ouray towards the Los Pinos agency is due north, and four miles from Ouray, in this direction, the Uncompaghre receives from the east the Red Cafion Creek. Following up the narrow caftan we find the section through white.. sandstone in strata dipping to the north and west, and belonging either to the lower or middle Devonian system. Presently the steep cafion-liko character of the ravine gives place to more gentle slopes, and we have entered crystalline rock-porphyry. The contact is well marked, for the sandstone, to a depth of from six to ten feet, resembles quartzite, i. e., is semifused. Ascending still higher, a small

Jan 1, 1881

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Rudolf Lesch

Till date, coke has been produced mainly from coals with a content of volatile matters in the range of 20% to 28% and good coking properties. If such so-called "selfcoking" coals are available, blast furnace coke or foundry coke with the required quality characteristics can be produced in top-charged horizontal ovens. In this case, the possibility of using high-volatile coals and in particular coals with low-caking properties is very restricted. Even if high-volatile coking coals have good coking properties, coke produced from such coal alone will not meet the requirements in terms of coke strength. The mechanical coke properties are influenced by the charge coal blend and the coking conditions. In this context, the bulk density of the oven charge is a decisive factor. Research and development in the field of coke production in horizontal chamber ovens aims at improving the specific oven throughput, increasing the raw material basis and introducing environmental protection technologies. The key factor, however, is to guarantee and further improve the rentability of the coke production. It is very important to reduce the cost of the charge coal to a minimum at the same time maintaining or even improving the coke quality.

Aug 17, 2017

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959