Search Documents

By Alexander Knoll, Dwight L. Baker

THE work herein reported shows that galena in certain organic solutions of fatty acids becomes coated with lead soaps, and that this coating is not only highly water-repellent but is also repellent to certain organic liquids, particularly those [ ] of high surface tension; i.e., nitrobenzene, diphenylmethane. WETTING PROPERTIES OF GALENA IN NONAQUEOUS FATTY ACID SOLUTIONS When a "captive bubble"' is withdrawn from a polished, plane galena surface under a nitrobenzene solution of stearic acid, the air bubble shows a decided tendency to "cling" to the mineral surface. The contact angle, therefore, was greater than zero, although it was not large enough to be measured quantitatively by the captive-bubble method.* [ ] When pure nitrobenzene was substituted for the nitrobenzene-stearic acid solution, no clinging of the bubble was observed; viz., contact angle = zero. Although the contact angle developed in air-galena-nitrobenzene-fatty acid solution was small, the organic solvent repellency of the galena surface was great enough to enable good recovery in a laboratory flotation cell.2 In Table I are given the results of flotation experiments using several different fatty acids dissolved in nitrobenzene.

Jan 1, 1941

By R Ashworth, S J. Hall

During trials which began in May 2005, traditional steel dump bodies for transporting iron ore on 220-tonne haul trucks at a Labrador iron ore mine were compared to a novel rubber suspended dump body. Loads were measured and compared over some 93 700 loads, representing more than 20 Mt transported. Maintenance costs and downtime were also measured over the course of the trial, which lasted nearly one year. This paper outlines the parameters and results of the trials. Parameters measured included payload and production improvements, carry-back reduction, downtime due to body maintenance, and wear on the floor of the suspended dump body. These parameters were then compared to those for conventional steel dump bodies in use at the mine, and conclusions were drawn. The resulting comparisons were significantly positive in favour of the new suspended dump bodies, confirming that each truck could haul an additional 41 000 tonnes per year, that downtime hours could be considerably reduced, and that body availability and service life can be extended through use of the suspended dump body. There was also a high level of operator acceptance of the suspended dump bodies due to less loading shock and a smoother ride.

Jan 1, 2007

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

By Hugh M. Roberts, R. D. Longyear

Introduction ............................ 27 GEnERal Geology........................... 29 The ORebodY in Western Falco~ridgI TownsRip........... 31 Quartzite-Graywacke Formation................... 33 Greenstone............................ 33 Norite ............................. 33 Metamorphism.......................... 35 The Orebody........................... 36 Mineralogy ........................... 37 Grade of Ore........................... 42 Genesis oF tEe Ores . :....................... 43 Summary of Various Hypotheses.................. 44 Magmatic Segregation by Crystallization of Sulphides........ 44 Gravitational Segregation of Molten Sulphides at the Base of the Magma 45 Intrusion of Molten Sulphides after the Consolidation of 'he Nurite.. 45 Deposition by Hydrothermal Solutions.............. 46 Magmatic Segregation by Extraction from Crystallizing Norite... SO The Relationship between the Exploration and Theories of Origin .... 50 Volume Relations of Norite and Sulphides............... 62 Intimate Association of Norite and Sulphides............. 53 Granitic Material........................ 54 Uniform Content........................ 54 Sulphides in Walls......................... 54 Absence of Typical Hydrothermal Minerals.............. 55 SUmmaRY................................ 56 Introduction During 1916 and 1917. the E. J. Longyear Co. of Minneapolis. Minn., carried out a campaign of exploration for nickel-copper ore in the Sudbury District of Ontario. The work was initiated by W. E. Smith. a resident of Sudbury. who called the attention of W. J. Mead. Chief Geologist

Jan 1, 1918

There remains considerable controversy in the industry regarding precision type detonators and where the end user can benefit from their use. In spite of the fact that electronic detonators and other prototypes were tested over one decade ago, explosive suppliers have hedged on full scale production for many reasons. Although some of the reasons were based on solid economics, others were strongly influenced by shear internal resistance within the corporate objectives, ultimate fear of market rejection, indecision as to what degree of precision was required and limited data on defining the real benefits to the end user.

Jan 1, 1992

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By S Davidge, J Pile, R Schumann, E Kepe, W Stewart, M Ridd, B Rathi

Geographical constraints, including steep terrain and high rainfall, at the Ok Tedi copper-gold mine in PNG’s Western Province present Ok Tedi Mining Limited (OTML) with significant challenges in mine waste management. Waste management includes discharge of tailings into the local river system and storage of waste rock from the mine pit in waste rock dumps which erode into the river system. Copper bearing skarn mineralisation is associated with a massive sulfide (mainly pyrite) deposit. Consequently, waste rock and tailings can contain significant amounts of pyrite. Without appropriate management, these waste streams represent a risk of producing acid and metalliferous drainage (AMD) when discharged to the river system. Throughout the life of the project, OTML have developed evolving strategies to manage mine wastes and mitigate AMD.

Aug 2, 2023

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By I. K. Choi

In a recent paper by Smith and Wen(1) the adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite was studied. As would be expected considering the general negative character of kaolinite, except perhaps at quite&apos; acid pH values (2,3,4), it was found that trimethyldodecylammonium chloride adsorbed strongly on kaolinite at basic pH values. Furthermore, it was found that sodium dodecylsulfate adsorbed strongly on kaolinite at acid pH values, particularly at initial 1H values below pH 3 (final pH values near pH 4). It is interesting to note that adsorption of the anionic surfactant was strong under conditions where the kaolinite was apparently slightly negatively charged (2). The present paper reports on an extension of the work by Smith and Wen. In this paper the effects of the presence of dodecyl alcohol and sodium hexametaphosphate on adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite are considered.

Jan 1, 1967

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By I. Yu. Melekestseva

The Semenov hydrothermal sulfide cluster (13º31´N), consisted of five fields (Semenov-1, -2, -3, -4, and -5), was discovered in 2007 in the 30th cruise of R/V Professor Logatchev [Beltenev et al., 2007; 2009]. The hydrothermal fields are located on a seamount composed of ultramafic and mafic rocks, gabbro, plagiogranite, and their altered rocks. The Semenov cluster is considered to be the largest sulfide accumulation in the Ocean with massive sulfide (MS) resources of about 40 million tons [Beltenev et al., 2009]. MS of the Semenov-1, -3, -4, and -5 hydrothermal fields are mostly characterized by marcasite-pyrite composition whereas rich copper-zinc MS with high Cu and Zn contents (11.37?19.33 and 5.89?18.32%, respectively) and anomalous Au and Ag grades (22?188 ?127?1787 ppm, respectively) were dredged only at the Semenov-2 hydrothermal field associated with basalts (13°31.13´N, 44°59.03´W; 2360?2580 m of depths) [Ivanov et al., 2008].

Jan 1, 2010

By V. B. Teffo

The aim of the project was to experimentally determine the coefficient of restitution, and static and rolling friction of Eskom-grade coal for discrete element modelling (DEM). These parameters will be used in further DEM studies to simulate the flow and behaviour of coal during conveyance. For the simulation to yield realistic results, the parameters for the different coal shapes identified in the samples were determined. DEM uses spherical particles, and it was found that the difference between the DEM default parameters and those measured is significantly different, by as much as 97%, which illustrates the importance of experimentally determining these parameters. The spherical particles in DEM can be used to construct the various coal shapes identified, and the parameters measured can be used to simulate realistic results. The conveyance system can then be optimized accordingly.

Jan 1, 2013

By M. I. Mthenjane

"BackgroundThe paper discusses post-mining land use however, the essence of the topic is the emotional motivation behind the decisions related to mining investment and development. Therefore this is not a typical SAIMM technical paper about the science and techniques of post-mining land use. There are already numerous papers written and conferences held on this aspect of post-mine land use; the science is well understood, but the evidence of the practical application of the (environmental, social, and economic) science is sparse. At a recent conference held in November 2017 on the theme of ‘Science, Business, Society Dialogue – linking science, society, business and policy for the sustainable use of abandoned mines in the SADC region’, it was demonstrated through the delivery of several papers on the possible viable options of post-mine land use. The conference was structured in nine sessions, covering the following relevant topics:? Sessions 1 and 2: Nature and magnitude of the problem: raising awareness? Sessions 3 and 4: International experiences in remediation: case studies? Sessions 5, 6 and, 7: Technological solutions: converting liabilities into assets? Session 8: Implementing solutions: social and legal aspects? Session 9: Wrap up, lessons learned: conference resolution.Summaries of the key outcomes of the sessions are available for reference.The aim of this paper, accompanied by the video speech, is to provide a visualization of the possibilities of post-mine land use. Mining contributes approximately 7% to South Africa’s GDP - this is the lowest it has ever been and is attributable to both a diversifying economy and to poor mining and investment policy which has resulted in reduced investment in the sector. The objective of the paper is to highlight the opportunities, for succeeding and diversifying economic activity following mining and mineral extraction which can continue to sustain the livelihoods and wellbeing of communities and societies beyond mining.During mining, very few alternative and local economies develop. Dependence on mining and its value chain prevails until mining ceases. This idea is conveyed in Figures 1a and b."

Jul 1, 2019

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By Ulrich Maidl

The use of EPB shields in the so-called mixed face conditions has set new demands to man and machine in EPB shield tunneling. EPB shields were initially conceived to drive in the pressurized closed mode in soft ground, whereas hard rock TBMs were designed to work in the unpressurized open mode. The present use of EPB shields in hard rock and mixed face conditions requires the combination of both technologies by finding best compromise solutions. This paper deals firstly with the geotechnical and mechanical interactions between machine and ground. Further on the critical points such as tool wear and tool replacement are exposed, together with a proposal of best solutions.

Jan 1, 2003

By John Chipman, Wayne L. Worrell

Using recent thermodynamic data for the carbides and oxides of tantalum, columbium, and vanadium, the stable solid phases aboue 1300°K and at 1 atm CO(g) pressure in each M-C-O system have been determined. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures necessary to obtain these metals by carbothermic reduction under reduced pressures. TANTALUM, columbium, and vanadium react with carbon to form the M,C and MC carbide phases. The M,C carbides have narrow homogeneity ranges, but the MC phases possess considerable ranges of homogeneity.&apos; The free energies of formation of the MC carbides were recently measured, and those of MC and M2Ccarbides have been estimated., (The notations MC and MC denote, respectively, the carbide compositions at the carbon-rich and at the metal-rich boundaries of the homogeneous MC phase.) In this paper, these carbide data are combined with thermodynamic data for the oxides to predict the stable phases in the Ta-C-O, Cb-C-O, and V-C-O systems at specified temperatures and oxygen pressures. M-C-O PHASE DIAGRAMS The solid phases in equilibrium above 1300°K for each M-C-0 system are shown in Figs. 1, 2, and 3. Above 1300°K, the vapor would consist entirely of carbon monoxide; and these phase diagrams were obtained by specifying the vapor pressure of CO(g) to be 1 atm. The temperature at which any two solid phases become unstable is specified along the two-phase equilibrium lines in each diagram. To simplify the diagrams, all solid phases in the Ta-C-O and Cb-C-O systems are represented as stoichiometric compounds. However, the homogeneity ranges of VO and VC are indicated, because they form a complete series of solid solutions.3 It also should be noted that the homogeneity range of

Jan 1, 1964

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997