Search Documents

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

William B. Phillips, Birmingham, Ala.: The questions raised by Messrs. Wilkens and Nitze are in the highest degree interesting to owners of low-grade iron-ores, aizd no less so to blast-furnace managers. If it can be shown that ores heretofore considered worthless can be brought within the limit of economic use, many large and readily accessible deposits may come into market on the one hand, while on the other the possible increase in the output of the furnace per ton of ore used will prove of advantage to the iron-maker. It cannot, of course, be claimed that this process has been employed on a working-scale with respect to iron-ores, and in so far as concerns results on a large scale no one is any wiser than his fellow. Granting that the results obtained in an experimental way (and certainly the experiments were conducted with a great deal of care) can be attained in practice, we would still be facing the question, what it would cost to get them. In the absence of any specific data, we have to fall back on general principles, helped along, as far as possible, by indications afforded by the experiments. I must confess that as regards the Clinton ores, which I have studied to some extent, I am not sanguine of making a ton of 53 to 54 per cent. concentrates from less than 1.75 tons of 40 per cent. raw ore. It may be possible to get the iron in the heads to 56 to 57 per cent., but the lesser richness of the middlings will probably reduce this to 53 to 54 per cent. in the salable stuff. As the authors remark, it is not worth while to discuss the concentration of the better grades of " soft" Clinton ore; for the price at which they are now delivered at the furnaces, and the comparatively limited amount now remaining, render their concentration unadvisable. If it is to succeed in the Birmingham district, the process must be applied to the low-grade soft and hard ores now con-

Jan 1, 1897

By Arnold Dix, Oliver Heger, Bernhard Kohl

In the USA, risk-based decision making has not been a common approach to tunnel safety in the past, but this is changing, as concepts such as “equivalency” in the NFPA 502 framework gain acceptance in the USA and elsewhere. In other regions, in particular in Europe, risk assessment techniques have been used for nearly two decades in many jurisdictions as an additional tool to complement the application of prescriptive guidelines and support decisions related to tunnel safety. After some initial difculties these methods are meanwhile a well-established element of tunnel safety management. There are several tools available which have been practically applied and further developed over years, such as the Austrian tunnel risk model TuRisMo, or the PIARC owned DG-QRAM model. Whereas TuRisMo is a holistic, system-based model, which is best suited to quantify and assess re risk and associated mitigation measures, DG-QRAM focusses on the risks related to the transport of hazardous materials. Depending on the objectives and the scope of the investigation and the regulatory environment tunnel risk assessment tools are in use for different purposes, mainly to demonstrate a sufcient level of safety and to decide on and select additional risk mitigation measures. The international eperience substantiates that the general approach is eible and that the methods and tools are mature and can be applied for different problems in different environments. First case studies like the risk study on conditions and permissibility of the transport of hazardous materials through the Eisenhower-Johnson-Memorial Tunnel in Colorado demonstrate the applicability of a risk-based concept for decision making in the US-American environment.

Jun 23, 2024

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

The early identification of a kimberlite dyke and the occurrence of pyrope garnet grains along a section of the Munro Esker north of Kirkland Lake encouraged the search for kimberlites. Subsequent exploration using data from aeromagnetic surveys completed for the Kirkland Lake Initiatives Program (KLIP) resulted in the discovery of five kimberlite diatremes in the area north of Kirkland Lake and another one to the south. These are only a portion of the cluster of pipes found so far that probably occur in the area. Recovery of the diamonds present in four of the pipes yielded 16 stones, the largest being 0.17 carats. Unfortunately evaluation of the pipes is a problem due to the cover of glacial drift, up to 92 m in thickness, which makes it difficult to obtain an adequate bulk sample. A study of their ages, mostly from drill hole samples, suggest that the kimberlite diatremes and other alkaline ultramafic rocks were emplaced along a northwesterly zone of rift structures. These alkaline ultramafic rocks cut across all earlier rock types and have ages ranging from 121 Ma to 173 Ma. The zone of deformation, along which these rocks occur, has been named the Lake Timiskaming Structural Zone (LTSZ), a modification of Lake Timiskaming Rift Valley (LTRV). Ultramafic intrusions which were emplaced along the LTSZ can be traced from the James Bay Lowlands in the northwest to past Belleville on the north shore of Lake Ontario in the southeast, a distance of about 1070 km. As the emplacement of these rock types become known more are certain to be found by drilling selected aeromagnetic anomalies. The project has demonstrated that aeromagnetic surveys can be used successfully to identify covered kimberlite targets.

Jan 1, 1992

By J. Miller, B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand, and gravel (SSG) sector in the USA. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine. A validated numerical model was used to explore the potential behavior of the pillars and roof as loading conditions change. The validated model was used to compare changes in mining sequence, overburden depth, and the in situ stress field. This will allow mine operators and engineers to have a better idea of the conditions that could be encountered as mining progresses. Results from the numerical modeling indicate that roof displacement more than doubles as the vertical stress increases from 10 MPa (1450 psi) to 19 MPa (2750 psi) when the maximum and minimum horizontal stresses were 41 MPa (5950 psi) and 22 MPa (3190 psi), respectively. Consequently, as the pillar load increases, the safety factor of the pillars is projected to decrease by about 25%. The impact of the practical application of numerical models can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 2, 2021

By M. B. C. Brandt

Richter magnitudes for seismic events were calibrated for use as a Local magnitude scale in the West Rand (WR), Far West Rand (FWR), and Klerksdorp–Orkney–Stilfontein–Hartebeesfontein (KOSH) gold mining areas. Richter magnitudes are currently calculated from seismograms recorded by local surface cluster networks using tabulated calibration values for Southern California, published in 1958. The Richter (1958) model is incorrect for distances of less than 30 km and should be applied only to crustal earthquakes in regions with similar attenuation properties to those of Southern California. When compared to the South African National Seismograph Network (SANSN), the cluster networks, on average, overestimate seismic event magnitudes by approximately 0.1 of a magnitude unit. A calibrated Local magnitude scale was derived by means of a multiple regression analysis between the Local magnitudes reported by the SANSN and the largest zero-to-peak trace amplitudes measured on the cluster network horizontal seismograms, after modelling the attenuation of the seismic waves as these progress from the epicentre to the station position. Magnitudes reported by individual stations for the same event show a significant scatter around the average magnitude owing to the near-surface amplifications of the seismic waves at the recordings sites. Average magnitude should be estimated using as many magnitudes of individual stations as possible to ensure an accurate estimate. Larger event magnitudes should be compared with those recorded by the SANSN.

Nov 1, 2021

By James P. May

Operating mine haulage trucks near the crest of stockpiles and waste dumps is a potentially hazardous practice often resulting in a localized slope failure and a dump point accident. The U.S. Bureau of Mines has developed a computer code (INSLOPE3) based on the kinematic method of limit analysis which determines an admissible truck weight (upper bound value) for varying distances from the slope edge. The program considers the material strength parameters, slope geometry, and inertial forces induced by vehicle braking. The program can be utilized to assist in the determination of safe operating distances for a haulage truck from a slope edge, the development of safe vehicle operating procedures, and the admissible weight for a static concentrated loading near the crest of an otherwise stable slope. This report provides information on the use of INSLOPE3, interpretation of the results for mining applications, and instructions for acquiring a copy of the software.

Jan 1, 1991

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By R. G. Aspden

Crystals with an (001) [loo] initial orientation of an iron-base alloy containing 3 pct Si were cold rolled with and without the use of constraints. A major difference in the rolling and annealing textures was observed between crystals rolled with and without constraints. These data show that the contribution of constraints at grain boundaries in a poly crystalline sheet should be considered in applying textural data on single crystals to grains in an aggregate. SILICON-iron alloys with a cube texture have been recently developed and their magnetic characteristics reported.1-4 Of interest in the development of this texture were the textural changes of single crystals accompanying rolling and annealing and the influence of constraints at grain boundaries in an aggregate on the behavior of individual grains. The present study was primarily concerned with the effect of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001)[100]. Barrett and Levenson5 were among the first to observe an influence of constraints at grain boundaries on the textural changes of individual grains during deformation. They tested Taylor&apos;s6 theory of plastic deformation of face-centered-cubic metals in which deformation textures were predicted. About one-third of the grains in poly crystalline aluminum did not rotate as predicted. Grains of the same initial orientation were observed to rotate in different directions under the influence of applied stress and anisotropic flow of neighboring grains. Recently, the various inhomogeneities of flow of crystals in an aggregate have been studied7&apos;8 and reviewed.9-11 Barrett and Levenson" rolled (001) [loo] iron single crystals inserted in close-fitting holes in copper to limit lateral flow and to simulate rolling of grains in an aggregate. Deformation bands were formed after a 90 pct reduction in thickness, and the cold-rolling texture contained two components described by rotating the (001)[100] about 35 deg in both directions around the normal of the rolling plane. No annealing textures were reported. Chen and Maddin13 rolled molybdenum single crystals initially (001) [loo]. The crystals were mounted between two hardened silicon-iron plates and 96 pct reduced in thickness by rolling at a low rate of reduction, about 0.0001 in. per pass. The deformation texture had the mean orientation of (001) [loo], and the azimuthal spread included orientations described by rotating (001) [loo] about 35 deg in both directions about the pole of the rolling plane. The presence of deformation bands were not reported by Chen and Maddin or detected in subsequent work of Ujiiye and Maddin.14 The ideal orientation of the annealing texture was (001) [loo]. Recently, Walter and Hibbard 15 reported on the textures of 3 pct Si-Fe alloy crystals initially near (001) [loo]. Each crystal was in an aggregate cut from a columnar ingot. After 66 pct reduction by rolling, the texture consisted of two symmetrical components which had the orientations described by rotating (001) [loo] about 30 deg in both directions about the pole of the rolling plane. Annealing texture was near (001) [loo]. In the above work, the textures of body-centered-cubic crystals were studied after rolling under the influence of constraints. The deformation textures varied from (001) [loo] to near the (001) [110] type and appeared sensitive to the manner in which the crystals were rolled. No textural data were available on the effect of rolling (001) [loo] crystals with and without constraints. The purpose of the present work was to evaluate the influence of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001) [loo]. Rolling and annealing textures were studied for a) crystals rolled with no constraints at different rates of reduction, and b) crystals rolled with constraints imposed by neighboring grains and by plates between which a crystal was "sandwiched". PROCEDURES AND EXPERIMENTAL TECHNIQUES Data are presented on four crystals which are representative of several crystals studied. The orientation of each crystal prior to rolling was (001) [loo] as determined by the Laue X-ray back-reflection method," i.e., each crystal had an (001) within 3 deg of the rolling plane and [100] within 3 deg of the rolling direction. These crystals were obtained from two iron-base alloys containing 3 pct Si by weight which were prepared by vacuum melting electrolytic iron and a commercial grade of silicon. Crystals 1, 2, and S-1 were cut from a large single crystal grown from the melt of one alloy by the Bridgman technique17 in an apparatus described by

Jan 1, 1960

A. Bement, Chicago,Ill. (communication to the Secretary*):— Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible," notwithstandirig that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combuition-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term " combustible " was an advance to be credited to the engineer rather than to the chemist, because the latter, not having to do with the interpretation of analyses in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash- and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression pure coal, which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Jan 1, 1909

The Thirty-sixth, Regular Meeting of the Rocky Mountain Coal Mining Institute was called to order at the Shirley-Savoy Hotel, Denver, Colorado, Thursday, June 23, 1938, at 11:15 o&apos;clock a.m., by Thomas Allen, Vice-President for Colorado, who announced that owing to the serious illness of Fritz Nyman&apos;s father, Mr. Nyman would be unable to attend the convention. Vice-President Allen welcomed the convention as a representative of Governor Ammons. Owing to the overlapping of a previous engagement, Mayor Benjamin F. Stapleton regretfully arrived too late to welcome the gathering in behalf of the City of Denver. Vice-President Allen selected Mr. F. W. Whiteside to preside at the morning session. On motion made, seconded and carried, the reading of the minutes of the Thirty-fifth Regular Meeting was dispensed with, inasmuch as they are printed in the proceedings. Chairman Whiteside suggested that the appointment of the personnel for the Committee on Resolutions, Nominating, Membership and Auditing be deferred until later in the meeting, and on motion made by Mr. Oliver, duly seconded and carried, this suggestion was adopted.

Jan 1, 1938

By Shamim A. Dar, & Samsuddin Khan, & K. F. Khan, Mohd Shuaib

The Late Paleocene–Middle Eocene phosphate nodules of Solan District of Himachal Pradesh belong to green facies of Subathu Formation of Sirmur group. Field observations indicate sporadic distribution of phosphatic nodules in the yellow brown to rusty brown, buff-colored bleach shales. Phosphatic nodules are dull earthy to dark grayish in color and break with sharp and conchoidal surfaces. Studies of phosphatic nodules using petrological microscope, X-ray diffractometry, and scanning electron microscopy (SEM) attached with energy dispersive X-ray (EDX) reveal that cryptocrystalline apatite (fluorapatite) is the dominant phosphate mineral. Silt sized silica is the dominant gangue, whereas pyrite and muscovite are present as minor gangue. The phosphate minerals occur as oolites, pellets, and cryptocrystalline apatite in the groundmass. Silica veins form a network replacing the original phosphatic matrix. Brown to brownish black color may be attributed by the organic matter in the phosphatic nodules. Completely phosphatized radiolaria and partially pyritized planktonic foraminifera are observed. There is corroboration of organic matter in the form of microbial filaments in the groundmass of apatite. The findings in the present investigation indicate that the different forms of the minerals, their texture, and distribution in the phosphatic nodules might be due to environmental vicissitudes in oxidizing to reducing conditions followed by replacement processes. Presence of microbial filaments may be due to the active role of microorganisms during the formation of these phosphatic nodules.

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.&apos;&apos; The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.&apos;&apos; The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian&apos; and others&apos; to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,&apos; then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß&apos; phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß&apos; and [-phases. The phase diagram in the ASM handbook&apos;" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß&apos;, the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By Samuel G. Lasky

In a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of Mining and Metallurgy, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose. we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step—the decision whether exploration should be undertaken—rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. Philosophy of Appraisal If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. flow then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects have already been ex-

Jan 1, 1949

By Samuel G. Lasky

In a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of Mining and Metallurgy, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose. we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step—the decision whether exploration should be undertaken—rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. Philosophy of Appraisal If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. flow then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects have already been ex-

Jan 1, 1949