Search Documents

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By H. H. Fields

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pittsburgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No.2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

The South Mine, property of Broken Hill South Limited, is situated at Broken Hill, NSW, Australia, towards the southern end of the main lode. The leases (MLs 7 and 8) cover a length of 2400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1940 feet below the collar of the original main shaft and to 825 feet below sea level. Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30 000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet. A typical assay for a monthly period is 14.4 per cent Ph, 5.6 ozs Ag, and 11.6 per cent Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and zinc concentrates produced are railed to other centres for the extraction of the contained metals.

Jan 1, 1994

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By Alejandro Sanz, Juan Luis Magro, David Mazeyrie

The Hampton Roads Bridge-Tunnel Expansion Project (HRBT), initiated by the Virginia Department of Transportation (VDOT), will add two new 1.5-mile TBM bored tunnels to the two existing immersed-tube tunnels between artificial islands, part of the connection between Norfolk and Hampton under the Hampton Roads Harbor in Virginia, USA. The new bored tunnels will be built by Hampton Roads Connector Partners (HRCP), a joint venture of Dragados USA, Vinci Construction, Flatiron Constructors and Dodin Campenon Bernard. This paper covers technical discussions that led HRCP to select a Variable Density TBM to address the challenges of this tunnel project, including but not limited to (i) the diameter of the bore: a 46 feet (14.04 m) diameter machine that constitutes the second-largest TBM ever used in the United States; (ii) shallow ground-cover under the water table; (iii) challenging and varying geology along the alignment, with mixed-face conditions and different types of ground modification zones; and (iv) the high TBM operating pressures required—all these and other challenges in a sensitive marine environment.

Jun 13, 2021

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By Robert H. Dickson

Limestone replacement and contact metamorphic orebodies are 80 irregular that sampling and estimating are far less. exact than in more regular types of deposits; both the mineralized masses and the lenses of ore within them are extremely irregular. So much development work is required to find the ore that the expense of blocking out great tonnages is prohibitive; furthermore, the rock near these orebodies is so heavy that drifts or raises cannot be kept open for many years without excessive repairs. As a result, few mines in limestone have more than three years supply of ore in sight. As most of the ore, is developed by stoping— not by drifting, raising, or drilling—estimates of ore developed do not indicate the total amount of ore that may be expected; they simply indicate the relative condition of the mines. But even if they are to do this, they must be made according to a fixed plan, intelligently carried out. The estimates of ore in the Calumet & Arizona Copper mines, Warren District, Ariz., have been of much value to those who plan the mining and development work. This paper describes the methods of sampling and estimating used in these mines. Sampling Samples are taken in various ways and depend on the condition of the working and the purpose for which the sample is to be used. Drifts, crosscuts, and raises are sampled by channels or by taking a grab off each mine car as it is filled. Stopes are usually sampled by drill holes or by taking a representative sample off each mine car; the latter, or chute, sample is by far the best sample. All workings are studied periodically by an engineer, who makes graphic and detail notes of the geologic structure, as shown in Fig. 1. The daily car tally and assay of each particular working is added to the same sheet opposite the material it represents. These sheets make a permanent record, showing the exact boundaries as well as the grade of ore in all workings.

Jan 1, 1925

By M. C. Simmons, Boyd Gutorie

Desulfurization experiments at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville on virgin light distillates obtained from some ‘high-sulfur’ crude oils have shown that the octane numbers of the original distillates are increased on the average about one unit, that the octane numbers of distillates with 4 ml. tetraethyl lead are increased 2 to 3 units, and that the The Petroleum Experiment Station, at the request of the Petroleum Administration for War, instigated and has in progress an investigation of crude oils of the United States to determine their possibilities for yielding straight-run distillates suitable for use as base or blending stocks to produce high octane aviation gasoline. One phase of this investigation deals primarily with so-called ‘high-sulfur’ or ‘sour’ crude oils by seeking to determine the effects of sulfur removal upon the virgin distillates prepared from these crude oils. To date, virgin distillates from several ‘high-sulfur’ crude oils from Texas, New Mexico, and Oklahoma have been prepared and desulfurized in pilot-plant distillation and desulfurization units at the Petroleum Experiment Station. The properties of the undesulfurized and desulfurized distillates were determined and compared to show the effect of sulfur removal. Results of these investigations showing the suitability of these crude oils as sources of virgin naphtha aviation base stocks have been prepared and forwarded to the Petroleum Administration for War and other approved persons. The following preliminary summary is presented to acquaint those interested not only with the present results of the investigation of several ‘high-sulfur’ Texas, New Mexico, and Oklahoma crude oils, but also to give some basic information as to certain sulfur compounds, especially their identification in straight-run distillates, their depressing effects upon the octane numbers of leaded fuels, the benefits obtained by their partial and complete removal, and some of the processes being used to effect their removal.

Nov 1, 1943

By F. Louis Grammer

The following study of flue-dirt and the influences controlling it may be interesting to many. It is published because it represents observations at about thirty furnaces at different times. It may assist in giving an impetus to the making of similar observations elsewhere. Until ten years ago, the metallic waste in furnace-gases was not considered a problem of pressing urgency in iron metallurgy—certainly not in the blastfurnace end of it. Many plants at present ignore, or pay but little attention to, top-pressures. Prior to the introduction of Mesabi ore, the losses in escaping gases, if considered at all, were regarded as thermal losses, or losses of fuel (except by those interested in lead, zinc, silver, etc.). In a high-priced material like ferro-manganese, such losses were, indeed, considered important. But the behavior of the Mesabi ores, corning, as they did, in practically inexhaustible quantities, could not be disregarded by the furnaceman. These ores came to stay. The tables appended below have purposely been altered to disguise the plant, the company and the ores used. The comparative values are maintained. In these tables, the influencing elements and conditions which are constant, or practically so, namely, size of furnace, quantity of wind, fuel used, etc., are not mentioned. The figures represent observations consistently followed up for a long period. The weights of flue-dirt were obtained from cars on which no other dirt was thrown. The analyses and calculations are based on the best of sampling. The effects of slips are excluded. Slips should not occur at well-regulated or properly-constructed furnaces, excepting under unusual and rare conditions. Allowances are made for moisture, scrap charged and silicon in the metal. The cutting effect of Mesabi

Jan 1, 1904

By Zhao-Qun Ke, Wen-Feng Tan, Jiang Diao, Yu-Hao Liu, Bing Xie, Zhang Tao, Wang Zhou, Hong-Yi Li

An effective way to decrease the dephosphorization burden in the current vanadium extraction-steelmaking process is slagging with CaO in vanadium extraction step. The phase composition of vanadium slag with different basicity and the regularities distribution of elements have been investigated by X-ray diffraction analysis and scanning electron microscopy combining with energy disperse X-ray spectrometry, respectively. The results indicate that V mainly concentrates in the spinel phases; Ca and P are rich in the silicate phases. Fe2SiO4 transform to CaFeSiO4, while the basicity of vanadium slag is 1.3. With further increase of basicity, 2CaOSiO2 could form in the silicate phases. Moreover, the phosphorus-containing phase will transform from Ca3(PO4)2 to Ca3(PO4)2-nCa2SiO4. With the increase of P2O5 content, the crystallization rate of spinels decrease obviously. Furthermore, the peak temperature for crystallization of spinels decrease 5 K with the P2O5 content increasing 1 wt%.

Mar 1, 2017

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By Mowat D. M., Louis H., Smith W. Mackey W. M., Dron R. W., Ellison C. C., Winmill T. F., Kerr G. L., Haldane J. S., Ashworth J., Garforth W., O'Shea L. T.

Discussion of Winmill's paper, including various anecdotal examples, is presented together with the author's response; topics included: the need to distinguish cubic pyrites from the rapidly decomposing rhombic form known as marcasite; the effects of moisture content in the coal and air; the possible effect of pressure; the heat insulation resulting from heap/stack size; and the means of determining pyrite and moisture contents

Dec 1, 1916

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man&apos;s thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life&apos;s work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe&apos;s pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe&apos;s work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book&apos; on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe&apos;s ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By S. Hobo, M. Yagisawa, T. Uchida, C. Tokoro, T. Kato

In this study, quantitative modeling was carried out for the treatment of simulated waste water containing As(V), Zn(II) and Hg(II) as toxic elements, and Fe(III), Na(I) and sulfate as coaxing ions. The objective was to predict the pH and residual concentrations of all the elements in solution after the neutralization/co-precipitation treatment. To accomplish this, the removal mechanism for As(V) and Hg(II) by ferrihydrite precipitation was first investigated for simulated waste water containing only As(V) or Hg(II). From the experimental results, it was confirmed that the removal mechanism involves not only surface complexation but also surface precipitation. However, surface complexation is the main mechanism for As(V) and Hg(II) removal to meet the target levels regulated in Japan. Next, the surface complexation model was constructed for the removal of As(V) and Hg(II) by ferrihydrite. The specific surface area and site density were determined from reference values proposed by Dzombak and Morel (1990). By comparing the experimental and calculated results, it was confirmed that our constructed model could successfully represent the experimental results. Furthermore, the surface complexation model was coupled with chemical equilibrium calculations and applied to the neutralization of simulated waste water containing As(V), Hg(II), Zn(II), Na(I), Fe(III) and sulfate. The constructed model could successfully represent the pH edge for As(V), Hg(II), Zn(II), Fe(III) and SO42- removal. In addition, the constructed model could represent the ion balance. Thus, our constructed model is useful to estimate the amount of neutralizer that is needed to achieve a target pH.

Jan 1, 2016

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By Levente Becze

The zinc bottom dross is obtained as a by-product from hot dip galvanizing operations and contains at least 92 % zinc, which is recycled mainly by pyrometallurgical processes. The overall costs of such a treatment, however, are often relatively high, and the very strict environmental protection regulations might also cause additional difficulties for the high temperature procedures in the future. Therefore, a novel hydro-electrometallurgical process has been developed in our laboratory, by which one can reclaim zinc of high purity, while attempting to achieve low energy consumption and making allowances for all the environmental restrictions. This aqueous processing technique, based on electrolytic refining in a cell equipped with anion-exchange membrane to separate the anode and cathode compartments, allows the indirect purification of the anolyte. Zinc is dissolved from the anode along with some of the impurity elements, while the intermetallic compounds (Fe-Zn, Fe-AI- Zn) are accumulated in the anode slime.

Jan 1, 2003