Search Documents

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

By Kirk Ellison, Eric S. Lindquist, Peter Faust, Stephen M. McLandrich

"The 181 Fremont Tower will be an 800-foot high-rise with a 60-foot deep basement located in a dense urban part of downtown San Francisco. The design and construction methods of the subsurface elements navigated a variety of site constraints such as loose fill and soft estuarine soils, shallow groundwater, contaminants, historic obstructions, small work area, proximity of adjacent buildings, and the on-going excavation and build-out of the adjacent Transbay Transit Center (TTC) train box. Design of the approximately 260-foot-deep drilled shafts (some of the deepest foundations ever constructed in San Francisco) was proven by a full-scale load test that provided unique data on the frictional capacity of the deep soil and Franciscan Complex bedrock in the region. Design and construction of the shoring system for the 5-story basement excavation was exceptionally challenging because of the on-going construction for the TTC. To allow for flexibility during construction, hydraulic rams were placed in a transfer waler along the shared TTC shoring wall that could adjust the forces transferred through to the TTC excavation if required. Open and steady communication between the shoring engineer, the geotechnical engineer, and the shoring/foundation contractor was crucial in order to satisfy the complex constraints of this site.INTRODUCTIONThe 181 Fremont Tower is a new build mixed-use tower, currently under construction in the dense urban core of the South of Market District of San Francisco, California. This high-rise will consist of 54 above ground floors with the roof level 700 feet high. Atop the roof will be some architectural features including a spire that will top out at just over 800 feet, which will make it the second tallest building in San Francisco upon completion.The tower is being developed by Jay Paul Company and the architectural design is by Heller Manus. The structural engineer and geotechnical engineer for the project is Arup North America Ltd (Arup). The shoring designer is Brierley Associates (Brierley). The general contractor is Level 10 Construction (Level 10) and the specialty foundation contractor and excavation contractor is Malcolm Drilling Co., Inc (Malcolm)."

Jan 1, 2017

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation, and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice, making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being beaded by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems test suited for the work in hand. The following projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration of a linear relation between surface and coercive force in magnetic minerals and its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1, 1934, to June 30, 193b.

Jan 1, 1936

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By L. Zhou, D. Bahrami, Y. Xue

Underground mine fires are a threat to the safety and health of mine workers. The timely determination of the location and size of an underground fire is of great importance in developing firefighting strategies and reducing the risk of any injuries. Machine learning was used in this paper to develop a predictive model for fire location and fire size in an underground mine. The ventilation data were obtained by simulating different mine fire scenarios with MFire. The ventilation data of all airways were used as features to predict the fire location. Based on the feature importance, five airways were selected to monitor, and the airflow data of the selected airways were used to predict the fire location and fire size. An accuracy score of 0.920 was obtained for the prediction of fire location. In addition, in-depth analyses were conducted to characterize the wrong predictions with the purpose of improving the performance of the random forest model. The results show that the occurrence of fire at closely connected airways at some locations can generate misleading ventilation data for each other and the model performance can be further improved by grouping them. Fire size is another factor affecting the model performance and the model accuracy increases with increasing fire size. The result from this study can help mine safety personnel make informed decisions during a mine fire emergency.

Mar 2, 2022

By R. E. Head

This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing, from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperative microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau of Mines, the Utah Copper Co., and the University of Utah.

Jan 1, 1935

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

Froth flotation processes are carried out in flotation cells that are grouped into banks, and these banks are interconnected, forming a flotation circuit. A literature review shows the existence of papers related to flotation circuit design based on mathematical programming. However, due to the complexity of solving the mathematical model in most of the work, it is considered that a small number of species is present in the feed to the circuit, which differs from practice. In addition, simple bank models are generally used. This paper presents a methodology for designing mineral concentration circuits that overcomes the problems mentioned. It allows the use of more suitable cell or bank models and the inclusion of several species. The methodology is based on two phases. The first phase identifies the set of optimal structures using discrete values of stage recoveries, solving several mixed integer linear programming (MILP) problems. In the second phase, the optimal design for each of the structures obtained in the previous phase is determined using a suitable model for the recovery at each cell or bank, which results in a mixed integer nonlinear programming (MINLP) model. The design of a copper concentration plant with eight species and the design of a zinc concentration plant with three species and five size fractions by species are used to validate the proposed methodology. The structure of the cells in the rougher and cleaner banks deliver structures that are novel.

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993