Search Documents

By W. E. Young

This paper describes operations of the Chief Consolidated Mining Co. at the Chief mine in the Tintic district, Juab County, Utah, where the outstanding problem is water control; the unique pumping methods employed are featured in this report. The ore bodies in this district occur as long, narrow shoots along fault fissures, usually in the Bluebell dolomite of Ordovician age. Oxide ores predominate above the 1800 level, which is also the natural water level. Sulfide ores containing lead, zinc, silver, and gold extend below the 1800 level. The mine is developed by vertical shafts and winzes, from which drifts are driven to the ore bodies. In the lower levels of the mine these drifts extend long distances from the shafts or winzes because of the relatively low dip of the ore shoots. The mine has been worked to the 2800 level and the 18-411 winze extends to the 3080 level.

Jan 1, 1958

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400' and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600' F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By R. G. Meara, O&apos

The land-pebble district of Florida, wnich in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of lime) or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the washing and formerly lost supplied the feed. During October, 1927, the United States Bureau of Mines in cooperation with the University of Alabama and the Missouri School of Mines and Metallurgy began to investigate the amenability of phosphatic sands to gravity methods of concentration. The work was under the immediate supervision of B. W. Gandrud, acting supervising engineer of the Southern Experiment Station of the U. S. Bureau of Mines at Tuscaloosa, Ala., and Will H. Coghill, supervising engineer of the ore dressing section of the U. S. Bureau of Mines. More comprehensive testing followed and in the early part of 1930 some of the companies cooperated with the bureau and the above-mentioned institutions in conducting a series of tests on hydraulic classification and tabling. The results indicated that marketable concentrates could be obtained with a recovery of 25 to 45 per cent of the phosphate formerly lost. As a result two companies have introduced hydraulic classification to treat the current tailings, and one of them has substituted classifiers for the 20-mesh screens which had been unsatisfactory. Because the phosphate grains and quartz grains have nearly the same specific gravity, the use of concentrating tables by the customary methods is not applicable. The washeries included in the following report are designated as Nos. 1, 2, and 3.

Jan 1, 1931

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator's training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By J. -B. C. Varnier, J. A. Cremeens, D. D. Overton

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County in Colorado in the United States were investigated using three-dimensional discrete element modeling methods. Large-scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back-analysis was conducted using prefailure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. IntroductionThe Pikeview Quarry is an aggregate quarry located approximately 8 km (5 miles) northwest of Colorado Springs in El Paso County, CO, USA. The quarry has been operated by several owners since the early 1900s. According to the U.S. Mine Safety and Health Administration (MSHA, 1986), the quarry has been a major source of construction aggregate for the Colorado Springs area for many years. In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy.A large-scale slope failure occurred on Dec. 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on Sept. 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure.The objective of this paper is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry, and both of these mechanisms were given equal credence in the present study. Quarry excavation and backfilling was a key factor in the slope instability for both failure mechanisms. The excavation was backfilled in stages in an effort to provide slope support. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability."

Jan 3, 2018

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By J. D. Hunt, R. J. McDonald

It is proposed that extensive fluid motion occurs between the dendrites of a Partially solid casting and it is suggested the A segregates in steel castings are a direct result of this motion. The fluid flow arises because of density differences between liquid ahead of the dendrites and the interdendritic liquid. Experiments are described on a model system investigating this fluid motion. The importance of interdendritic fluid flow is discussed with reference to longitudinal segregation. SERIOUS macro segregation is often found in large killed steel ingots. Among the most common segregates are those known as A and V, Fig. 1. The A segregates are arranged over the surface of cones, the wide parts being at the base of the ingot. The A segregates are pencil like in shape and extend from the columnar into the equiaxed region. The V segregates are distributed over inverted cones but have a less well defined shape. They occur at the center of the ingot. Because of the commercial importance of macro inhomogenities these segregates have attracted wide-scale attention. The segregates contain alloying elements and impurities which depress the freezing temperature and are thus the last liquid to freeze. A number of explanations have been proposed to explain their presence. It has been suggested1'' that the segregates are the result of the equiaxed zone growing towards the columnar region together with the interaction of convection within the bulk liquid. It has also been proposed that the segregates are the result of nucleation and rapid growth ahead of the dendritic front.3 Neither of these explanations is completely satisfactory because A segregates are pencil shaped and are not found as continuous cones. In this paper an alternative mechanism is proposed, and experiments are described on a model system to determine whether the mechanism occurs in practice. It is thought that A and V segregates are not peculiar to steels but should occur in many other large castings. Fluid motion within the bulk liquid region of a casting has been extensively discussed. Little attention has been paid to fluid motion within the partially solid regions. The work415 that has been done has been mainly concerned with the fluid motion which results from the volume contraction on freezing. The volume contraction is used to explain various types of macro segregation. The present authors suggest that in many cases the fluid flow resulting from volume contraction will be small compared with that due to other causes. When the columnar region is growing, the liquid still remaining between the dendrites has a much lower temperature near the ingot walls than at the dendrite tips. The composition of the liquid in contact with solid will vary with temperature. The density of the liquid will thus vary both because of changes in temperature and composition. The layers of different density liquid will give rise to a slow but steady liquid flow through the interdendritic regions. If there is no density change with composition, the temperature gradient within the dendritic region should give rise to a downward flow between the dendrites, shown schematically in Fig. 2. When the liquid density changes appreciably with alloy concentration this motion could either be en-

Jan 1, 1970

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955

By O&apos, R. G. Meara, M. M. Fine

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite. † In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.&apos; The outlook for the postwar market for fluorite is encouraging Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1947

By M. M. Fine, R. G. Meara, O&apos

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite. † In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.&apos; The outlook for the postwar market for fluorite is encouraging Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1947

By D. J. McAdam, R. W. Mebs

The technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. According to the prevalent view,8 the technical cohesive strength of a metal. in any particular state as regards prior mecharlical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress. In two previous papers by one of the authors, evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion Limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.&apos; In this paper, as in the previous papers,14.15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated 33, and the intermediate principal stress will be designated S². The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress."l4, .l5 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,15 however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average Of the three principal stresses.* This in fluence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers,".&apos;5 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant • Any stress system ma? be resolved into a polarsymmetric stress causing pure volume strain and a combination of pure shearing stresses. which cause no change of volum

Jan 1, 1945

By B. W. Naugle

The Bureau of Mines investigated the changes that occur in decomposition products when coal is carbonized in a fluidized bed with steam as the fluidizing medium and the vapors are subsequently cracked without condensation in a fluidized bed of high-temperature coke. The coal used was from the High Splint bed, High Splint mine, Harlan County, Ky. Since this coal is agglomerating, it was blended with char. The integrated unit used in this investigation consisted of a 3-inch-diameter fluidized coal carbonizer, a 3.5-inch-diameter cracker containing a bed of high-temperature coke fluidized by the tar vapors and steam from the carbonizer, and gas-cleaning and product-recovery systems. The carbonizer was operated at 485° C and the cracker at 600°, 700°, and 800° C. The process variables investigated were temperature, residence time, and concentration (pound of tar vapors per pound of steam to the cracker) of tar vapors in the cracker. The total tar yields decreased as the temperature of the cracker increased, and at a constant cracker temperature of 600° C the yield of paraffins, acids, aromatics, and olefins in the distillate increased directly with the tar vapor concentration in the cracker. At 700° and 800° C only the acids and aromatics increased with increased concentration. Bases remained essentially constant regardless of the temperature and concentration. Similar results were obtained when the tar from the carbonizer was condensed prior to feeding to the cracker.

Jan 1, 1965

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By John P. Hager, Adolfo R. Zambrano

The thermodynamics properties of the liquid Pb-Ag-Au system have been determined from galvanic cell measurments five pseudobinary systems of fixed XAg/XAu ratio. The galvanic cell employed a molten PbO-SiO2 electrolyte and was operated between 775" and 1030°C. The thermodynamics properties of lead were obtained directly from the experimental data, whereas the excess integral molar properties and the activities of silver and gold were obtained by means of the Gibbs-Duhem equation. The calculated proper -ties of the Ag-Au system agree well with the published properties. The liquidus surface of the Pb-Ag-Au system has been determined at 1200°K. In Parts I&apos; and 11&apos; the galvanic cell Mo,Pb(l)|(PbO-SiO2)(l) SiO2(s) |Pb(alloy)(l), Mo [I] was used to determine the thermodynamics properties of the Pb-Ag and Pb-Au systems, respectively. The use of cell I, in which a molten oxide electrolyte is employed rather than the classical fused-salt electrolyte, was shown to result in more accurate ther-modynamic measurements in that the displacement reaction at the alloy-electrolyte interface (l/Zb)B(alloy) + (I/za)A+Za = (1/Za)A(alloy) + (1/Zb)B+zb [1] was minimized. For the Pb-Ag system, where B = Ag(l), the error in the activity of lead (aPd) re-sulting from Reaction [I] was calculated to be less than 1 pct.l For the Pb-Au system the error in aPb was calculated to be less than 0.5 pct.2 Also, electro-transport measurements on the PbO-SiO2 electro-lyte1,2 established that the conduction was entirely ionic and that lead was present only in the divalent state. In the present study the experimental technique is extended to an investigation of the thermodynamic properties of the liquid Pb-Ag-Au system. Five pseudobinary systems of fixed X Ag/XAu ratio were selected. The experimental results were then combined with the previous measurements on the component binary systems Pb-Ag1 and Pb-AU2 to calculate, by means of the Gibbs-Duhem equation, the molar and partial molar mixing properties for the liquid ternary solutions.

Jan 1, 1970