Search Documents

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By L. L. Peterson, W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and truck at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. Haulage Cycle Established from Existing Operations For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between and the shovel and trucks with the new truck cycle times.

Jan 12, 1968

By John Johnston

The actual amount of any metal volatilized from a mixture of metals depends on the magnitude of its partial vapor pressure under the specified conditions of temperature, and on the circumstances attending the heating—in particular, on the duration of heating, the volume of gas coming into actual contact with the surface of the metal, the extent of this surface, and the rate of diffusion of the volatile metal from the body of the melt toward the surface.' If two (or more) metals are volatilizing from the same mixture of metals, the several conditions are identical except for the difference in partial pressure and in rate of diffusion of the volatilizing metals; the second of these two factors is without doubt only of secondary importance as it is probable that the rates of diffusion of the volatilizing metals would be very similar. Hence, in order to gain an estimate of the relative amounts of two metals that may be volatilized from a given mixture, it is necessary to know the vapor pressure, or, more precisely, to ascertain for each metal its partial vapor pressure in equilibrium with the liquid (or solid) alloy under the particular circumstances. The partial pressure of each constituent depends on the effective concentration of that constituent in the alloy2 as well as on the vapor pressure of the constituent when pure, and it can be calculated when both of the above factors are known. The first step, therefore, is to ascertain the vapor pressure of the several pure metals. Vapor Pressure of Pure Metals The experimental data on the vapor pressure of the several pure metals with which we are here concerned are not so accurate as could be wished, nor have the determinations been made in general at temperatures such that the results can be used directly. In a previous

Jan 1, 1919

By Thomas Rupp, Michael Siegwart

The paper presents the vibration and sound emission measurement campaigns carried out in 2007 in preparation for the Ceneri-Basistunnel construction. We also present the vibration measurement campaign conducted during the construction of the Zimmerberg-Basistunnel. Both tunnels form an integral part of the Swiss Federal Railway Company Neue Eisenbahn Alpentransversale project (NEAT). This strategic project comprised the construction of several new tunnels. Its aim is the improvement of the existing infrastructure. The improved infrastructure will be able to accommodate a larger volume of railway traffic that is also crossing the Alps at higher speeds. The construction of the Ceneri-Basistunnel commenced in 2006. Both the Zimmerberg-Basistunnel and the Ceneri- Basistunnel are located underneath densely populated areas. Therefore, noise and vibration emissions have to be kept to a minimum and must not exceed applicable codes of practice. In order to identify the most appropriate blasting strategy for the yet to be constructed Ceneri-Basistunnel, blasting trials were conducted. The paper presents the findings of these trials and identifies ways to reduce both noise and vibration emissions from blasting. The construction of the first phase of the Zimmerberg-Basistunnel took place between 1999 and 2003. While the first phase is already in operation, the construction of the second phase has been postponed (commencement originally due in 2007). The Zimmerberg-Basistunnel connects the outskirts of Zürich with the city centre. As the tunnel site was not located close to the surface near populated grounds, no special measures were needed to reduce the noise emissions from blasting. However during the construction of the tunnel, the vibration emissions from blasting were monitored on more than 50 locations on the surface. The paper presents the analysis of some of the data. An emphasis is placed on the appropriate synopsis and presentation of data for documentation purposes.

Jan 1, 2009

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By Helfried Nafe

"For about a century thermodynamically absurd facts have been propagated in conjunction with the iron-carbon phase diagram. These facts concern fundamental relationships of chemical thermodynamics. Attention is turned here to the discussion of only one of the relevant aspects of the subject, i.e. the definition of the thermodynamic activity of the solute and its implications for the iron-carbon solution.IntroductionThe view on the iron-carbon solution is characterized by the assumption that the solute may appear in two different forms, i.e. graphite and cementite. Accordingly, two carbon solubilities are differentiated, on the one hand for graphite and, on the other hand, for cementite. As a consequence, two versions of the phase diagram exist simultaneously, the application of which depends on the prevailing conditions, (i) the so-called stable phase diagram with graphite as solute and (ii) the metastable one that is based on the cementite-in-iron solution. These diagrams are joined together in the double phase diagram that originates from Heyn [l ], with the first ideas mainly going back to Stansfield [2] and Charpy [3].Thermodynamically, the most inadequate implication of the Fe-C double phase diagram is that the carbon activity may take values larger than unity. With the standard state of the activity being that of the pure substance, i.e. the Raoultian one, such a value implies the nonsensical existence ofa state purer than pure. The explanation of this physical state, ifthere is any, vaguely refers to supersaturation and, in the wider sense, to the physico-chemical phenomenon of metastability. Other aspects of chemical thermodynamics are likewise involved. Therefore, the comprehensive investigation into the present subject requires more topics to be considered than only one separate issue. Not only should the criticism of the present view be in the focus but also the discussion of new ideas capable of reconciling the experimental facts, known about the F e-C system, with the fundaments of chemical thermodynamics. All this, however, cannot be provided here because of the limited space available. As a consequence, in what follows only a part of the whole problem is under scrutiny, i.e. the definition of the thermodynamic activity and its role for the interpretation ofrelevant experimental facts."

Jan 1, 2014

By Michael Cruickshank

All life on Earth relies on the ocean and yet the ocean is 95 percent unexplored, unknown and unseen by human eyes,? said Paula Keener, director of education programs for National Oceanic and Atmospheric Administration?s (NOAA) Office of Ocean Exploration and Research. ?To better understand, manage and protect the ocean and its resources, NOAA believes it is critical to use the best technology to explore, discover, inform, educate and motivate? (MTS, newsletter, January 2011). In the last few decades, our understanding of the global mineral resource base has been drastically changed by some surprising new developments. The potential for commercial minerals per unit area in the oceans and seabed appears to be similar to that of the terrestrial lands. Thus, almost three-fourths of the global mineral resources are in, or under, the sea and are virtually undeveloped. The area of the Pacific seabeds alone is greater than the total area of the global lands. Half of the global seabed minerals are now controlled by nation states within their Exclusive Economic Zones (EEZ). The other half is controlled by the United Nations (UN) through the International Seabed Authority (ISA) within the ?areas beyond national jurisdiction? known as The Area. Thus, the Law of the Sea, ratified in 1994, has resulted in the largest transfer of control of natural resources in the history of mankind. This paper was prepared by the Society for Mining, Metallurgy and Exploration (SME) Committee on the Offshore Technology Conference for the SME Board of Directors and other interested parties. As the premier professional society for the mining and mineral community in the United States, with a history dating back to the 19th century, SME?s mission is to encourage and support young men and women engineers in the minerals industry, provide the services they need, improve the image of the industry, strengthen the networking among global industry professionals and engage in proactive collaboration among industry, government, academia and nongovernmental organizations (NGOs). The accomplishment of this mission can be strongly advanced by highlighting what is probably now the most significant development in the history of the modern minerals industry - the exploration of the marine environment and the understanding of the potential for the development of the minerals therein.

Jan 1, 2011

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By S Li, Y Lei, X Wu, C Ma, W Q. Zhang

The failure of roof of thin bedrock working face under loose aquifer in a coalmine can lead to water-sand inrush disaster. Based on the accident of water-sand inrush in 30108 working face of a mine in Shaanxi province, China, the mechanism of water-sand inrush is theoretically analysed. The process and critical conditions of water-sand inrush in working face are reproduced by numerical simulation where the bedrock thickness is 20 m, the clay layer thickness is 40 m and the mining height is 6.5 m. The study found that under the condition of thin bedrock and thick clay layer, the characteristics of the clay layer have a significant inhibitory effect on the development of the fractured zone, and the development of the water-conducting fractured zone is incomplete and insufficient. However, in the process of continuous mining of multiple adjacent working faces, the strength of the clay is gradually reduced by the influence of mining and the erosion of water, and the height of the fractured zone is gradually increased. In the subsequent mining process of the working face, the roof is more likely to be cut-off and lead to water-sand inrush. From the initial failure of the clay to the final crack directly through the surface, the shear strength of the clay is reduced by about 52 per cent. Further simulation found that in addition to the characteristics of the clay layer itself, the main factors affecting the water-sand inrush in the working face caused by overburden failure also include the difference in bedrock thickness and strength, and the difference in coal seam mining height. With the increase of bedrock thickness, the development height of the fractured zone increases gradually with increases of bedrock thickness when the cutting failure of overburden rock no longer occurs. With the increase of mining height, the height of water flowing fractured zone also increases, but the cracking ratio gradually decreases. Therefore, it’s of great practical significance to systematically study the mechanism and critical conditions of water and sand inrush in mines and the main influencing factors for preventing similar accidents in mines with similar conditions.

Nov 29, 2022

By W. B. Agocs

IN August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model II total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey. The area surveyed is located at approximately 41°00'N and 74o28'W, just south and east of the town of Green Pond, N. J. The outstanding topographic feature of the region is Copperas Mountain, a well defined ridge, maximum elevation 1222 ft, which runs the entire length of the survey. The lowest point in the survey, 810 ft, is in the extreme eastern corner. Topography of the area is shown in Fig. 1. The three major rock units outcropping in the area are all metamorphic: the Pochuck gneiss, which has been divided into two metamorphic facies; the Byram gneiss; and the Green Pond conglomerate. The relative ages of the Pochuck and Byram formations, both pre-Cambrian, are in doubt, but it is believed that the Pochuck is the older of the two.' The Green Pond conglomerate is Silurian.' Distribution of the outcrops and mine locations is shown in Fig. 1. Two facies of the Pochuck gneiss can be distinguished locally—the Copperas Mountain and Kitchell members. The Copperas Mountain member is a hornblende gneiss, and all the mines and prospects in the area are in this unit. The Kitchell is a quartz-plagioclase feldspar gneiss. The Byram gneiss is a relatively nonresistant valley formation which is high in the potash feldspar. The Green Pond conglomerate is a well indurated quartzite-conglomerate which forms the Copperas Mountain and the Green Pond Mountain's ridge to the north. It overlies the gneisses with a strong angular discordance that may be a fault. The geologic structure of the Green Pond area is relatively uncomplicated. The foliation planes of the gneisses dip steeply to the southeast, and the Green Pond conglomerate dips steeply to the northwest. Additional faulting in the area is indicated at the contact between the Kitchell member of the Pochuck and the Byram along the base of the topographic spur extending to the southeast from Copperas Mountain. The magnetite mines of Pardee, Winter, Davenport, Green Pond, Copperas, and the Bancroft shaft are described by Bayleyl and Stampe2.' The ore is in the Copperas Mountain member of the Pochuck gneiss. The magnetite veins are 10 to 50 ft wide and up to 300 ft long, dipping to the southeast at angles ranging from 40" to 75". The locations of these mines are shown in Fig. 1. Dip Needle Survey: The dip needle survey shown in Fig. 2 was taken from a U. S. Bureau of Mines Report of Investigations." The figure numbers below the local, individual map area outlines refer to the figures in the aforementioned reports which were not contoured. The area of the dip needle survey was confined almost exclusively to the outcrops of the Pochuck gneiss. The separation between survey profiles was 100 ft and the distance between stations on the profiles was 25 ft in highly anomalous zones to 100 ft in magnetically flat areas. A total of 16 1/2 miles of traverse was surveyed over an area of approximately 1/2 sq mile with 2050 stations. The magnitude of the magnetic anomalies is difficult to determine due to the lack of information concerning the type of dip needle used and the procedure followed in making the dip needle survey. This latter would include the method of "zeroing" the dip needle and the procedure of reading at the stations, whether on the swing or statically. Calibrations made of the Gurley dip needle, Lake Superior type, show a static sensitivity of 385 gamma per degree in the range from —25" to +35o, corresponding to a variation in the total field of —9600 gamma to +13500 gamma in a total field of 57000 gamma, inclination 72". The sensitivity increases to 16 gamma per degree from a deflection of 60" to 76", and from 76" to 172" the sensitivity decreases continuously to a low of 260 gamma per degree. From the above it may be seen that it is difficult to assign an arbitrary sensitivity for the dip needle used on this survey. However, an estimated value of 100 gamma per degree may be assigned. On this basis, the majority of the magnetic anomalies, whose deviation is +20°, would be 2000 gamma. Locally, west and northwest of the Pardee mine the magnetic anomaly is +50°, or 5000 gamma; in the Green Pond mine area deviations of +75" are observed that would correspond to anomalies of 7500 gamma. The areal extent and width of the dip needle magnetic anomalies is comparable to profile and station spacing. Hence it is concluded that part of the detail may be due to control, and the probable cause of the magnetic anomalies is at or near surface exposures of magnetite concentrations in the form of veinlets and disseminations whose locations correspond to the local magnetic anomalies. On the basis of the magnetics, none of the magnetite concentra-

Jan 1, 1956

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

By G. Zain, Abdel-Zaher M. A. Abouzeid, Y. S. Mustafa, A. A. S. Seifelnassr

The main forces acting on minerals in conventional size reduction units are compression, impact, attrition, and/or abrasion. Usually a combination of these forces shares the breakage action of the minerals with one or more of these forces dominating the breaking action, depending on the machine used. The present work concentrates on the behavior of quartz when stressed with compression force in a confined piston die. Several size fractions within the size range minus 10 mm to plus 0.85 mm were compressed in the piston die. The measured parameters are compression load, bed thickness, displacement as a result of compression, rate of displacement, and the size distribution of the products. It was found that the size distributions are, to some extent, different from those produced by the ball mill or the high-pressure roll mill. This is mainly because of the differences in the type of the acting forces in each case. It was also found that the cumulative weight of the distributions is reasonably normalizable with respect to the median particle size of the product. The specific energy expended is inversely proportional to the median size of the products, and the reduction ratios, xf/xp, are directly proportional to the applied compression force, and hence, to the specific energy expended. A simple model is suggested for predicting the particle size distribution as a function of the expended energy. The calculated values of the size distributions match fairly well with the experimental values, except at the very low energy levels, where most of the energy expended is consumed in the rearrangement and packing of the particles in the confined space with little or no breakage.

By B. Csoke

To improve the efficiency of the crushing/screening plant of Bazalt-Középko Kobányák Ltd. (Hungary), the implementation of computer aided quality control is planned. In the current phase, the R & D work aims at the solution of high-priority tasks: 1) Developing the process models, validation of the models by means of industrial measurements. 2) Developing the algorithm for the process control of the crushing/sizing plant. 3) Developing the suitable computer program. To develop the mathematical models of crushing (breakage and probability functions) and to determine the model parameters, the experimental industrial trials were carried out on hydrocone crushers of types Svedala H 4800 EF and H 4800 F, changing the gap size and crushing relatively narrow grain size fractions. Additionally, the parameters of the separation function for the screens operating in the system were determined. It was established that the crushing probability depends on the grain size of the feed (Y) and the gap size (s), so the breakage probability S, for each cone crusher, can be well characterised by the function formed using the ratio of these two parameters: SfYsf==. The distribution of the broken grains can be described reliably using the relative grain size distribution function B(? = x/Y) (usually Schuhmann-Gaudin- or Rosin-Rammler-shaped function). For the screens, the probability function ()2()111/NTx = xd ???---???? is suitable for cha-racterising the separation (where x? grain size, ?-open-area ratio, d ? rectangular screen aperture size, N ? number of appearance of the particle on a screen surface). Using these functions, the comminution circuits were described by means of vector/matrix equations. The calculations and measurements verified the reliability of the developed models and algorithms.

Jan 1, 2014

By ANDREW McVILLIAM, WILLIAM H. HATFIELD

AT the 1902 May meeting of the Iron and Steel Institute, the, authors presented a paper on " The Elimination of Silicon in The Acid Open-Hearth," wherein they recorded a few typical examples of certain Siemens charges out of a very large number specially watched for the purposes of that research. The main deductions drawn from those experiments have been accepted in all the intelligent criticism during or after the discussion on the paper. One opinion, however, was rigidly held by all who mentioned the matter, with the single exception, perhaps, of Mr. Lange, and that was the necessity for the attainment and the maintenance of an abnormally high temperature in order that the percentage of silicon in the metallic bath might increase, or that an unusually large proportion of silicon might be retained in the metal. The original decision was ar-rived at on the results of scores of trials, and has since been the subject of frequent experiment. The authors still retain their opinion that although, naturally, a higher temperature will accelerate the (probable) action between the carbon of the steel and the excess silica of the slag, they then fairly proved, and have now abundantly confirmed the fact, that around the temperatures occurring in Siemens steel-making practice the chemical composition of the slag, particularly with regard to its acidity, is the factor which determines whether the percentage of silicon in the molten steel shall increase or decrease. In the discussion in 1902 Mr. Saniter called attention to Mr. H. H. Campbell's work, and in the reply the authors also mentioned that of Messrs. Winder and Brunton of 1892, the two

Mar 1, 1905