Search Documents

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

By Ehsan Alavi, Glen Frank, Michael DiPonio, Mike Mooney, Lisa Mori

"A study was conducted on the N125 project in Seattle to investigate the use of apparent density as an assessment tool for the effectiveness of soil conditioning. The formation of an air bubble as well as the plugging of cutterhead and excavation chamber can be a result of improper soil conditioning. Both air bubble formation at the top of the excavation chamber and developing plugging issues can be identified by analyzing the apparent densities in the excavation chamber. In this study, apparent densities less than unity were observed in the upper portion of both northbound and southbound TBMs, suggesting the presence of an air bubble. Apparent densities greater than the in-situ soil density were observed in the lower portion of the excavation chamber. Particularly high values of apparent density were coincident with clogging observed at multiple locations along the alignment. The combination of less than unity upper chamber apparent density and very high apparent density in the lower portion of the chamber are related, and indicate the inability of the TBM to effectively condition and mix the soil in the chamber.INTRODUCTIONProper soil conditioning in EPB tunneling offers many advantages to the quality and productivity of the project. There are few operational parameters that can be used to assess the soil conditioning performance such as advance rate, torque, thrust, chamber pressure signature, etc. One of the other parameters that potentially can be used is the apparent density. The apparent density of the material in the chamber was introduced by Guglielmetti et al. (2003) as the vertical chamber pressure gradient calculated from the physical relation between the horizontally measured chamber pressures and the vertical distance between the pressure sensors. Guglielmetti et al. (2003) introduced apparent density as a measure to ensure the excavation chamber is filled with material. To guarantee face stability the authors suggest to keep the apparent density over a certain limit so the material is able to transfer effective stress to the virgin soil, and thus provide support of the excavation face. They implemented this method at the Metro project in Porto, Portugal.Comparing the vertical gradient of the horizontal chamber pressures to the densities of excavation chamber samples, Bezuijen et al. (2005) discovered that the gradient is not necessarily representative of the muck density. They assumed that the yield stress of the muck as well as the adhesion between the muck and the cutterhead and bulkhead material have an influence on the vertical gradient during mining (Bezuijen et al. 2005, Bezuijen & Talmon 2014)."

Jan 1, 2016

By G. A. Swanquist

INTRODUCTION This article describes the yellow cake drying, packaging and dust collection circuit of the United Nuclear Church Rock Mill. It also describes the layout and floor plan of this section as well as the operation and performance of the various equipment. In order to place the yellow cake section in perspective of the mill as a whole, the mill circuit is described briefly. CHURCH ROCK MILL GENERAL DESCRIPTION The Church Rock Mill contains six operating sections shown in Figure 1 in block diagram form. The grinding section consists of a semi-autogenous mill in closed circuit with a hydrocyclone. The slurry is then routed to the leaching tanks. Sulfuric acid and sodium chlorate is added to dissolve the uranium. The pulp is transferred from the leach tanks to the thickeners where the uranium bearing liquid is separated from the barren solids. The uranium bearing solution is then filtered and pumped to the solvent extraction section. [ ] In the solvent extraction section, the uranium bearing aqueous solution is brought into contact with an organic solution composed of kerosene, amine and isodecanol. The amine extracts the uranium from the aqueous solution. This organic solution is then routed to the stripping section, where the uranium is removed from the organic solution with an ammonium sulfate aqueous solution. The pregnant stripping solution now concentrated to 30 gpl U308 is routed to the precipitation tanks where ammonia is added to precipitate the uranium. The yellow cake is then washed in a counter current circuit of two thickeners and one centrifuge to remove impurities, mainly sulfates in order to meet specifications. The centrifuge centrate is routed to the second wash thickener for forward wash. The centrifuge cake at approximately 50% solids consistency is transferred to the yellow cake dryer via a screw conveyor. YELLOW CAKE DRYING, PACKAGING AND DUST COLLECTION Figure 2 shows the flowsheet of the integrated circuit of drying, packaging and dust collection. This section of course centers around the yellow cake dryer as the main equipment. The other main units are the dust collectors for the dryer and packaging respectively, a yellow cake storage bin and the yellow cake packaging facilities. Physically, all of this equipment occupies four floors, beginning at the top floor: 1. Both dust collector fans, the centrifuge and the screw conveyor to transport the yellow cake to the dryer. 2. The dryer, fire box and both dust collectors occupy the third floor. Figure 3 shows the floor plan of the third and fourth floors. 3. The yellow cake storage bin and dryer dust collector sump are located on the second floor. 4. The ground floor houses the loading facilities consisting of two load out ports from the bin to barrels, a roller conveyor loop, drum weighing scale, and change room facilities. Figure 4 shows the ground floor plan. Figure 5 is an elevation view of this section showing the overall equipment arrangement.

Jan 1, 1981

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had' under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman's report was published in the Engineering and Mining

Jan 10, 1910

By C. C. Stevenson, Thomas Varley

"The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along chemical and metallurgical lines to state definitely just what place it will occupy in the metallurgical industry. The theory upon which the process operates has received the attention of prominent metallurgists for the past twenty years, and research and experimental work has been conducted by many investigators.Much of the experimental work done has never been published, and it seems that the accumulation of such results if made known would be an important aid to the further development of the process. The object of this paper is, therefore, to bring salient features of the process to the attention of the metallurgical industry, both for the purpose of furnishing information, and receiving from interested parties any comments which the reading of this article may suggest. A bulletin covering the work done at the Intermountain experiment station of the U. S. Bureau of Mines, situated at Salt Lake City, Utah, is in course of preparation.The chloridizing roast is usually accompanied by appreciable losses due, to the volatilization of the metals as chlorides during the roast, these losses often running as high as 30 per cent, depending upon the temperature, the character of the ores and the associated gangue material. It was not until 1891 that Croasdale, (Croasdale, Stuart, Engineering and Mining Journal, Aug. 29 1903) by observing this and stack deposits from the chloridizing roast, recognized the possibility of making volatilization a major instead of a minor feature of the roast. He then made tests on a large number of tires from different, localities, the result of which showed the, general application of the process. The main difficulty, as stated, by Croasdale, was the lack of a suitable means for recovering the fume from the furnace gasesIn 1913, Cottrell (See Mining and Scientific Press, March 29, 1913; alsoTrans. American Institute of Mining Engineering, September 1918. (Additional informa-tion is available from the owners, The Research Corporation of New lark, and Western Precipitation Co., .Los Angeles, Calif.), announced his invention of the electrostatic precipitator, which solved the problem of separating the solids from the furnace gases."

May 1, 1921

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By Wilbur H. Somerton

W. H. Somerton is to be commended for his application of the methods of dimensional analysis in combination with the results of laboratory drilling tests to obtain a significant formula for the rate of penetration for the process of rotary drilling. This formula is shown to be a consequence of a more general formulation developed by the discussor as a result of his investigations of the basic action of most methods of rock drilling by mechanical means—the momentary loading of a chisel-shaped tool on the surface of the rock at the bottom of the hole. Some of the author's conclusions are re-examined in the light of this general formulation. DRILLING RATE FORMULA The author selects a minimum number of the most significant variables associated with the rotary drilling process to set up his two dimensionless parameters. Only one variable is associated with the geometry of the bit —the bit diameter, D; only one variable is associated with the properties of the rock pertinent to drilling— the drilling strength, S; and only two independent variables are associated with the conditions of operation the weight on the bit. F, and the rate of rotation, N. The dependent variahle of interest is, of course, the rate of penetration, R. The results of the author's drilling tests show that the variable R that appears in the dimensionless parameter, RIND is approximately proportioned to the square of the variable, F, that appears in the other dimension-less parameter, F/D2S. This establishes the functional relationship between these two simple parameters that leads to the formulation of a third dimensionless parameter, RD1T2/NF1. This last parameter is a significant one for the rotary drilling process, in general, although the author properly limits the validity of his equations to his present test conditions. The author realizes that the numerical value of this parameter, C, is not a constant but may be a function of one or more additional dimensionless groupings of the many other variables associated with the rotary drilling process, e.g. some dimensionless measure of bit wear. The author's parameter is shown to be a special case of a more general dimensionless parameter, developed by the discussor. that is applicable to practically all methods of rock drilling by mechanical means, namely. RD2S/P. P is the rate at which mechanical work is done on the rock, and S is the drilling strength, a term originated by the discussor. S is defined as the ratio of energy input to the rock to the volume of rock broken

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

By Joseph D. Davis, GEORGE S. POPE

This bulletin is the fourth of a series a showing the results of the purchase of coal by the Government under specifications. The work of inspecting and analyzing coal delivered on Government contracts was transferred to the Bureau of Mines by an act of Congress effective July 1, 1910. It had been carried on for several years before that date by the technologic branch of the United States Geological Survey. The purchase of coal on the dealer's statement as to quality or on the reputation of the mine or district producing the coal is gradually being discontinued. At present most coal-purchasing contracts make definite provision regarding the desired heating value of a coal and the composition as shown by analysis. The heating value is usually expressed in British thermal units" and the composition specified is that shown by proximate" analysis. The price to be paid for delivered coal is made to depend on whether the analyses and heating-value tests of samples representing the delivery show the quality to be above or below the quality set forth in the contract. Large coal consumers are beginning to appreciate more and more the importance of the cost of power as a factor in the cost of producing a finished article. The endeavor to increase the efficiency and the economical operation of a power plant calls for an intimate knowledge of the quality of the coal being used. The purchase of coal under specifications insures the purchaser getting what he pays for and the coal being of the quality guaranteed. In addition, the analyses and tests of the delivered coal furnish data whereby the power-plant results can be comprehensively studied and a continuous check maintained on the conditions of operation.

Jan 1, 1912

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By L. Sun

A numerical model has been developed to study the air flow in the flow plate and gas diffusion layer assembly on the cathode side of a PEM fuel cell. The flow plate in this type of fuel cell often has serpentine channels and the porous layer is adjacent to the flow plate to diffuse the air to the catalyst layer. Flow cross-over of air through the porous diffusion layer from one part of the channel to another can occur. This flow cross¬over is a result of the pressure differences between different parts of the channel, and it causes the flow rate through the channel to vary with the distance along the channel. A numerical study of pressure distribution and flow cross-over through the gas diffusion layer (GDL) in PEMFC flow field using a serpentine channel system has therefore been undertaken to compare the cases of a single channel and two parallel channels, with the channels having a trapezoidal cross-sectional shape. The purpose of the present work was to study the effect of the flow plate geometry on the basic fluid flow through the plate. The flow here has been assumed to be three-dimensional, steady, incompressible, isothermal and single-phase. The flow through the porous diffusion layer has been described using the Darcy model. The dimensionless governing equations have been solved by using the commercial CFD solver, FIDAP. From the results obtained, it can be found that the single channel systems have greater maximum flow rate difference than the parallel channel systems under the conditions considered in the present study. Also, the size ratio R of trapezoidal cross-sectional shape has a significant effect on the flow cross-over and pressure variation in the flow field.

Jan 1, 2005

By Victor G. Hills

CONTRARY to what seems to be the general impression, the island of Cyprus was not named for the metal copper, but the reverse was the case. The origin of the name is entirely lost. The ancient city Kition, the birthplace of Zeno, is supposed to be the same as Kittim mentioned in Gen. x, 4; Jeremiah ii, 10 and Ezekiel xxvii, 6, and Josephus states that this name seems to have been applied to the city and also to the island itself. Cyprus is 50 miles off the coast of Asia Minor. The mountains on the mainland are plainly visible across the sea from where I write six miles from the shore of Morphou bay. It is 200 miles from Joppa the port of Jerusalem, and 250 from Port Said. The shape of the island is like a lizard, the tail pointing directly toward the old city of Antioch near the northeastern corner of the Mediterranean. The island was once heavily timbered. Among the great trees the cedars were said to even excel the famous cedars of Lebanon. The Odyssey refers to it as the "sweet smelling island" and makes other references. But the continual wars of every race and age completely stripped it of its timber, and for centuries it has been woefully barren. There are two ranges of mountains. One borders the north coast and runs out in a slim rocky ridge forming the "tail." The other occupies the southwestern part of the island, the highest point being Mt. Troodes 6600 ft. high, sometimes called Mt. Olympus. Whether or not it be the Mt. Olympus, anyway right around there the ancient gods and godesses frequently "started things." These peaks are in plain sight 10 miles south from where I live.

Jan 1, 1926

SAMUEL L. HOYT.-The question of adding the ferromanganese to the ladle or to the furnace involves both theoretical and practical questions and its discussion might very easily occupy the rest of the day. One of the points to be kept in mind is the desirability of obtaining uniform steel. If ferromanganese is added to the ladle, it is necessary first to melt the manganese and then to distribute uniformly throughout the heat. The only heat available for this purpose is that of the molten steel itself. No doubt sufficient heat is present, but in our desire to pour the steel as quickly as possible there is hardly sufficient time allowed, many times, for the proper distribution of the manganese. In other words, this is an operation which takes a certain amount of time and any undue shortening of the time allowed must affect the quality and uniformity of the steel. Again, this particular method does not lead to as efficient a use of the manganese as might be desired; a contention which is based on theoretical grounds. In concentrated solution, manganese will completely reduce all the ferrous oxide, the presence of which I hypothecate and produce, as the reaction product, manganese oxide. In dilute solution, the manganese only partly reduces the iron oxide, but the manganesee oxide which does form dissolves the iron oxide in simple solution. The dissolution of ferrous oxide in the manganese oxide will result in a more economical utilization of the manganese and an equal purification of the heat. This whole point, at present, has not been definitely proved and its answer will involve very difficult research work. On the other hand, if the manganese is added to the furnace, the heat of the furnace is used to melt the alloy and there is plenty of time during tapping for the manganese to be very uniformly distributed throughout the steel. By distributing the alloy throughout the charge we can secure a better utilization of the manganese than is possible if the addition is made to the ladle. Certain other points, such as the recovery, have been dealt with at greater length in the paper.

Jan 4, 1919

By E. F. Kern, W. W. Loo

A review of the literature on the reduction of cassiterite showed that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world's consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue. The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents. Review of Literature Experiments on the smelting of Bolivian tin concentrates were made by James P. Gill in 1920 in the metallurgical laboratory of the School of Mines, and submitted as a graduate thesis. The results of these tests are fully reported as they are preliminary to the experimental part of this paper, and also because they have not been published. The variables investigated by Mr. Gill were: (a) the effect of temperature on the rate of reduction of cassiterite concentrates; (b) the time required for

Jan 1, 1928

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

IT is generally accepted that for transport of coal underground from different collecting stations, the system of endless rope haulage with remote control is not only one of the safest and most economIcal, but is also one of the most'efficlent in dealing with output.When the coal measures lie in regular planes, the work of laying down such a haulage presents no difficulties. When, however, the dip of the measures is Irregular, or dislocated by faulting, the management is faced with the problem of constructing vertical curves of such a radius that the sag of the rope will correspond with the road bed, and thus obviate the danger of the rope rising and throwing the skips off the track.The direction of the main roads for haulage purposes being ascertained from the plan of the royalty to be worked, the faults or dislocations in the seam are determined for these roads with the greatest possible accuracy by means of bore holes from the surface.From the data thus obtained the haulage road can generally be so graded that the rope will keep on the floor during haulage operations, although the grades may in places be synclinal.The writer confesses that he knows of no accurate formula for calculating the sag of the rope under varying tensions and so determining the safe radius of the curve, and he had to depend upon past experiences under somewhat sImilar conditions.The accompanying sections illustrate a case where the writer has recently installed an endless rope underground approximately 5000 ft. in length, from the foot of a tunnel in which an endless rope delivers the output to the screening plant, and having to negotiate, first a 400-ft. downthrow fault, and later a 32 ft. upthrow.

Jan 1, 1927

By John Roberts

THE Federal income tax law permits as a deduction in determining net income "in the case of mines, . . . a reasonable allowance for depletion and for depreciation of improvements, according to the, peculiar conditions in each case, based upon cost, including cost of development not otherwise deducted: Provided, that in the case of such properties acquired prior to Mar. 1, 1913, the fair market value of the property (or the taxpayer's interest therein) on that date shall be taken in lieu of cost up to that date." The law provides for a reasonable allowance but the regulations provide for a definite method of computation that possesses more the virtue of simplicity than that of reasonableness. Article 210 of Regulations 45. reads: "When the cost or value as of Mar. 1, 1913, or within 30 days after the date of discovery of the property shall have been determined, and the number of mineral units in the property as of the date of acquisition or valuation shall have been estimated, the division of the former amount by the latter figure will give the unit value for purposes of depletion, and the depletion allowance for the taxable year may be computed by multiplying such unit value by the number of units of mineral extracted during the year." This is simple, but is it reasonable? The intent of the law is clearly that the cost of the ore in the ground shall be considered as part of the cost of the same ore when removed and sold. The regulations fail to carry out that intent, because of the unwarranted assumption that all the ore in the mine cost the same amount per ton. This is what gives the Treasury Department's method its simplicity, but at the same time robs it of its reasonableness because the assumption is contrary to fact.

Jan 1, 1921

By Line Hallgren

The fluid flow in the mold during up-hill teeming is of great importance for the quality of the cast ingot and therefore the quality of the final steel products. At the early stage of the filling of an up-hill teeming mold, steel enters, with high velocity, through the nozzle into the mold and the turbulence on the meniscus could lead to entrainment of mold flux. The entrained mold flux might subsequently end up as defects in the final product. It is therefore very important to get a mild and stable inlet flow in the entrance region of the mold. It has been acknowledged recently that swirling motion induced using a twist tape swirl blade, in the submerged entry nozzle is remarkably effective to control the fluid flow pattern in both the slab and billet type continuous casting molds, resulting in increased productivity and quality of the produced steel. From the above result, we propose, swirling flow generated through a swirl blade inserted into the entry nozzle, as a new method of reducing the deformation of the rising surface and the unevenness of the flow during filling of the up-hill teeming mold. The swirling blade has two features: (1) to generate a swirling flow in the entrance nozzle and (2) to suppress the uneven flow, generated/developed after flowing through the elbow. The effect of the use of a twist tape swirl blade was studied using both numerical calculations and physical modeling. Water modeling was used to assert the effect of the swirling blade on rectifying of tangential and axial velocities in the filling tube for the up-hill teeming and also to verify the results from the numerical calculations.

Jan 1, 2006