Search Documents

By John E. Sherborne, William M. Newton

The value of the electric log as a means of interpreting underground structures has been increasingly demonstrated by its almost universal present-day use. It becomes important, therefore, to be able to evaluate the factors that affect the values obtained. By far the greatest number of electric logs are measured today in boreholes filled with rotary mud, the properties of which may exert an important influence on the electric log. In an effort to establish what the order of magnitude of such effects might be, a series of investigations was made in the laboratory and the field. Apparatus suitable for either field or laboratory use was designed and a procedure established for determining the factors that affect the resistivity of drilling muds over a wide variation in mud condition. Five muds representative of the types of clay-base muds employed in California were tested and the following observations were made: 1. The effect of raising the temperature from 8o° to i8o°F. is to decrease the resistivit~ of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity. The results of the investigation indicate that the mud resistivity is materially affected by the addition of electrolytes whether these are added for the purpose of conditioning the mud or enter the mud when salt beds or highly saline structures are penetrated. It should be observed, however, that the magnitude of the effect produced upon the electric log by changes in mud resistivity is also dependent upon the relative salinity of the water en. countered in the formation being logged. The laboratory data are supplemented by field data, which indicate that both the self-potential and resistivity curves are influenced by mud resistivity.

Jan 1, 1946

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By Benj. E. Shackelford

THE present paper is concerned with typical temperature values experienced in lamp-filament measurements as made on regular factory and engineering products. It deals with the relations existing between temperature, efficiency, lamp size, and life of incandescent lamps, insofar as they affect the rating of the product and its use by the individual consumer. The temperatures measured lie in that range covered only by the general method of radiation pyrometry, as opposed to direct methods used under contact conditions. The range of temperatures ordinarily experienced extends from about 2125° K., for the now almost extinct carbon-filament lamp, to 3200° K. for the comparatively new tungsten-filament motion-picture lamp. Most of the more common sizes of tungsten lamps have temperatures ranging from 2500 to 3000° K. Because of the high temperatures involved and the relatively small area of the sources used, we are practically restricted to two methods of measurement, both of which depend on the light radiated front the filament. The first and more usual method is that of the Morse pyrometer, dependent on the variation in temperature of the amount of light of a given color range yielded by the filament. In this case, the measured temperature is that of a small part of the incandescent body, that is, the part which is focused on the comparison filament. The second method, known usually in this country as that of "color match" and in England as "color-identity" is based on the color of the total light yielded by the filament, the comparison being facilitated by the use of an ordinary photometer- head. A more definite idea of the temperatures involved in the case of filaments of various vacuum and gas-filled lamps, is given by Fig. 1. The size of the lamp, in watts, is plotted along the horizontal axis and the temperature of the filament is plotted along the vertical axis. The lamps concerned are regular product, rated for 1000 hr. life. The temperature values for the old 16-candlepower carbon lamp and the new motion-picture lamp are shown by the cross and circle respectively.

Jan 9, 1919

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone, quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide, The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over-burden was dug by hand labor, dumped to the quarry floor and trans-ported to the dump in quarry cars, Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi-circle around the top of the quarry about 200 ft. from the face and about 50 ft, above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river: As quarrying pro-gressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp,, 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft, above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting hays into which the motors are raised whenever the river reaches flood stage.

Jan 1, 1938

By H. F. McCullough

The success of a coal-mining venture as relates to operations at the gob or break-line, such as the drawing of pillars or the working of long-faces, depends upon the control of face conditions. The measures required to control the latter are dependent upon the action of the coal seam, roof and floor at and in the vicinity of the faces, but the manner in which these will act is dependent upon the rate of face movement as well as upon the facc characteristics and upon the forces exerted. Yet the merits of a method of working—the practicability of controlling face conditions and the means required for such control when applied to any particular case—are usually judged only upon a consideration of the characteristics of coal seam, roof and floor, and the manner in which they have been observed to act. Practically every coal-mining man knows that face conditions are influenced by the rate of face movement, but few have appreciated that this is as much of a factor in the control of face conditions as are the face characteristics and the forces exerted. Fewer yet have recognized or taken advantage of faster rates of face movement as one of the principal means of establishing control of face conditions or of securing more favorable face conditions. Seemingly inherent difficulties, particularly in the control of roof conditions, but also in the control of conditions of the coal seam and floor, are frequently mitigated or disappear when the rate of movement of the faces is sufficiently increased. The characteristics of the coal seam, roof and floor and the forces exerted upon them do determine the general trend or tendency of face action, but the manner in which the coal seam, roof and floor will act and be aeted upon and the magnitude of the action during the time the site of mining operations remains at any particular point are very largely determined by the rate of movement of the faces. Progressive Nature of Forces Exerted Coal seam, roof and floor are composed of materials having definite properties or characteristics. The potential or ultimate values of the

Jan 1, 1927

By H. E. Rorschach

Oil-field activities in Oklahoma made 1936 the best year since 1930. Approximately 2800 wells were completed, an increase of about 20 per cent over 1935. Purchasers' reports filed with the Corporation Commission showed a total of 200,240,252 bbl. of oil purchased from leases in 1936. The assembly of a complete table of the oil fields of the state was not achieved, as many of the early records of operators and pipe-line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. The outstanding developments of the year were: the discovery of rich Wilcox-sand production in the Moore pool; the spectacular drilling campaign in the Capitol or Mansion extension in the Oklahoma City pool; the surprising extension of the Olympic pool and the Hunton lime zone in the Fitts pool; and the failure to find more Ordovician production in southern Oklahoma. Wildcat discoveries, which were on a par with 1935, resulted in the discovery of such promising pools as Billings-Wilcox, North Bethel, North Earlsboro and North Lucien. The Fitts-Upper Simpson, Edmond, Jesse, Keokuk Falls and South Burbank pools underwent considerable development. Fitts Pool.—The Fitts area in Pontotoc County was greatly extended during the year and was the leader in drilling activity in the state. The producing limits were pushed to the east and north and the development of the Hunton lime horizon was outstanding. In the Upper Simpson zone 162 wells were completed; 137 in the Hunton lime zone and 26 in the Wilcox zone. The Oil Creek zone, a sand body below the Wilcox member, was discovered by the Magnolia-Statler No. 3 well located in the 1/4. 1/4 of sec. 28-2N.-7E. Moore Pool.—The Moore pool, in Cleveland County, which was opened in 1935 by the Sinclair Prairie-Franklin Community No. 1 well, surprised the oil industry when the Sinclair Prairie-Marvel No. 1 well, on Apr. 1, 1936, discovered a rich body of Wilcox sand below the distillate

Jan 1, 1937

By Henry H. Otto

The anthracite industry can be divided into two parts—the underground, or mining, and the outside, or preparation or manufacture. To understand recoveries in the two branches, some of the history of the industry and the changes that have taken place in the past century should be considered. It is a long step from 1807, when 55 tons were produced in the Wyoming field, to 1917, the peak year, when 80,841,223 tons were shipped to market from all the fields. In 1820, the Lehigh Coal Co., the predecessor of the Lehigh Coal & Navigation Co., shipped 365 tons in arks down the canal of the Lehigh Navigation Co. The Schuylkill field was not opened until 1822, when 1480 tons were shipped. The Wyoming field really became a producer in 1829, when 7000 tons were mined and shipped. It is well to note, at this time, the passing of the Coleraine colliery after a life of 88 years; in collieries of this age will be found the romance of the region, as well as the history of the changes to date. Mining Methods In the Lehigh region, the first coal came from the old quarry mines at Summit Hill; a little later the open-cut workings, or quarries, east of Jeansville, and near Beaver Meadow were opened. In the Wyoming field, it was necessary to resort to underground mining almost from the very first. Ashmead1 has described the changes in outside preparation methods, dl tending to increase the percentage of coal shipped to market. A description from the days when the lump coal was raked and screened out in the quarries or mines, to the modern breaker of today, shipping as high as 6000 tons of at least eight sizes of coal in an 8-hr. day is a very interesting story. Each size is a step toward increasing the yield from the property. With the belief that the supply was inexhaustible, the early mining was conducted with the thought of getting the maximum amount of coal on first mining. The superintendent was his own foreman and engineer.

Jan 1, 1925

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Frederic Benard

The electrolytic copper refinery at Copper Cliff, Ont., is operated by the Ontario Refining Co., Ltd. The associated companies behind the enterprise are the International Nickel Co. of Canada, Ltd.; The American Metal Co.; The Consolidated Mining & Smelting Co. of Canada, Ltd.; and Ventures, Ltd. The plant was the outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as closely as possible. The refinery is near the intersection of the Sault Ste. Marie to Sudbury highway and the Canadian Pacific Railway. It is about one mile south of The International Nickel Company's smelter at Copper Cliff. The standard-gage track systems of the refinery and of the smelter are connected by a standard-gage timber railroad trestle that crosses the railway and the highway by means of steel girder spans. The Canadian National Railway has access to the plant by means of this trestle and the nickel company's tracks, so that the refinery has connections with both the Canadian Pacific and the Canadian National railways, as well as a direct connection with The International Nickel Company's smelter, from which the bulk of the copper to be refined is hauled by the latter's electric locomotives. Buildings The refinery (Fig. 1) covers approximately 60 acres, enclosed by an unscalable chain-link fence. The main buildings have a content of 23,000,000 cu. ft., with a total roof area of approximately 600,000 sq. ft. and near them are the substation, cooling pond and main standard-gage track system (Fig. 2). A ladder track for car storage extends 1200 ft. south of the coal-pulverizer tracks and the scale house is on this spur. The intake and pumphouse for fresh water supply are at Kelly Lake, about 3000 ft. south of the plant. Owing to the severity of the winters, when temperatures of from 20" to 40' below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were

Jan 1, 1934

By Tao Chunhui

The seabed deposits type and distribution are very complex at the hydrothermal field. In this paper, we provided an approach to study the seabed deposits classification at the Precious Stone Mountain hydrothermal field (PSMHF) using MultiBeam sonar data . The PSMHF was found in the Galapogas microplate at the Leg 3 of the Chinese COMRA 21st Cruise. Using this approach, the seabed deposits at the PSMHF are mainly classified into three types, which are rock, breccia and sediment, respectively. We can find the distribution of the three types of seabed deposits according to the sonar backscatter data. The rocks are mostly distributed around the hydrothermal vent. The breccia are located at the foot of the vent. Most sediments are distributed at the southwest to the vent due to bottom current. Combining with seabed video, TV-Grab sample and the backscatter data, we draw the map of the seabed deposits distribution at the PSMHF.

Sep 14, 2011

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By Y. Hirosaki, H. Hamashima, Y. Itoh Kato, S. Tanaka

The emulsion explosives show non- ideal detonation behavior, and its detonation velocity can be controled by selecting the size and adjusting the quantity of voids involved. To establish the technology to control the detonation characteristics of the emulsion explosives, some experiments have been carried out using resin balloons of five different sizes ranged from O.OSmm to 2.42mm in the average diameter. Detonation velocities of the emulsion explosives containing resin balloons of different size and quantity were determined for the charge diameter of 20-50mm. The detonation velocity at infinite charge diameter was compared with calculated ideal detonation velocity. The emulsion explosives containing large (0.5mm or larger) balloons showed big discrepancy between the measured and calculated detonation velocities, and the fraction of ammonium nitrate reacted in the reaction zone was estimated to be significantly low. It was shown that the reaction zone length was proportional to the size of voids involved. The critical charge diameter was determined for the emulsion explosives containing different resin balloons at the various explosive densities. It is large for the emulsion explosives containing large voids, and it was shown that the critical diameter is proportional to the distance between the void surfaces, not to the void spacing, the distance between the centers of the voids. The reaction rate of the bulk emulsion matrix seems to be the major factor that affects the critical diameter than the specific surface of voids. Good relationship between the critical diameter and the reaction zone length was observed.

Jan 1, 2000

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By Walter Weeks

CONSIDERABLE difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be v1. The total head at the outlet is then h + v1/2g? The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Let f be the friction loss in the straight duct, s the shock loss in the dif- fuser, and V2 the velocity at the end of the duct. Then h+ v12/2g=v22/2g + f + s FIG. 1.-FAN ON DUCT. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established.

Jan 1, 1930

By V. Koump, R. H. Tien

An approximate mathematical solution is found for the problem of unidimensional solidification of a slab of a binary alloy with time-dependent surface temperature. For the model considered, the solid skin does not form until the liquidus front has moved a certain distance. This distance depends on the rate of cooling and can be as large as half the thickness of the slab when the cooling rate is small. Assuming that the THE process of unidirectional solidification of binary alloys with constant surface temperature was analyzed by the present authors in a recent paper.' In the previous analyses, the surface temperature was considered to be lowered instantaneously, at the beginning of solidification, from its initial value to some surface temperature decreases linearly with time and that the solidus and the liquidus lines are straight, calculations are made of the temperature and concentration distributions, movements of the liquidus and the solidus fronts, as well as changes of temperature, solid fraction, and solute concentration of the liquid at the center of the slab. arbitrary temperature, lower than the solidus temperature. Although the solution of the problem for the case of constant surface temperature has some practical applications, instantaneous changes of temperature are physically impossible. Present theoretical study of the unidirectional solidification of a binary alloy is based on a more realistic model, i.e., in this case, the surface temperature of the slab decreases from its initial value continuously with solidification time. The model of solidification within the solid-liquid region is the same as the one described in the

Jan 1, 1969

By Tsuchida N

The history of world nickel production has been affected significantly by the supply and demand situation and fluctuation of LME price of nickel metal. In the beginning of the 1980s, the decline of price and demand lead to the withdrawal of un-competitive producers and the shrinkage of the production capacity. During the same period, Sumitomo Metal Mining maintained the production level with continuous improvement of the traditional matte electrorefining process. However, Sumitomo has recognised that the continuous improvement alone does not promise us the ability to catch up with rapid changes in the world. In the meantime, Sumitomo intensively researched chloride hydrometallurgy and has developed the chloride process for the nickel refining. This includes the solvent extraction and chloride electrowinning in the mixed sulphide process and the chlorine leach of the anode slime arising from matte electrorefining. In the late-1980s, Sumitomo Metal Mining decided to develop a new nickel refining technology based on chloride hydrometallurgy. The new process was designed from the comprehensive aspects involving safety and the environment. Construction of the plant for the matte chlorine leach electrowinning (MCLE) process was commenced in 1991. The MCLE plant with a capacity to 2000 tonnes per month has been commissioned at Niihama since 1992. The process has provided high productivity, overall good economics and high quality of electrolytic nickel produced. After the establishment of the process, Sumitomo has maintained continuous improvement of the new process and has attained the best practice of the work classification.

Jan 1, 1996

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

These springs arc situated on the south bank of the river about four miles below the City of Great Falls. In addition to the spring on the bank there are several in the bed of the river. Estimates on the flow of all these vary from 350 to 600 cubic feet per second, and as the temperature is practically constant at 53° F. throughout the year, the effect on the river water is to prevent the formation of anchor ice at the Rainbow Fails power development below, trouble of this source being in evidence every winter at the Black Eagle Falls above. Geologists claim that the water of the Giant Springs is derived from seepage through an old pre-glacial channel of the Missouri River now occupied by Sand Coulee, five miles up-stream from Great Falls. The water in this buried channel seeps through the flat-lying sandstone of the region and again unites with the present stream at the site of the springs.

Jan 1, 1913

By H. H. Pentz

This paper gives the derivation of a practical formula for the calculation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 260 ft. per 1000. Derivation In Fig. 1, o represents the image of the shot point a. Then the length of the path acb is equal to ob and ae'd is equal to od. In the triangle aob, p is equal to ob, x is equal to , and c is equal to ao. The angle u is the apparent dip of the reflecting horizon. Angle oab is equal to (90" - u). The quantity m is the slope of a line tangent to the curve, defined by equation 1, at the point (p, x). The quantity m' is the slope of the line tangent to the curve at the point (p', 2').

Jan 1, 1940