Search Documents

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

By Donald O. Voit

A BASIC language program has been written that simulates the performance of an integrated solvent extraction circuit consisting of an extractor, a reflux fed scrubber, and a stripper. The program is designed to simulate the performance of a circuit having an aqueous feed containing each of the lanthanides as well as yttrium. The Kremser equation is used to determine the separation occuring in each section of the circuit. The required input variables are the feed composition, the separation factors, the light key extraction factors and extractor feed zone distribution coefficient, the number of stages, and the reflux ratios. The program calculates the composition of the streams at each node in the circuit, the total loading, and the remaining distribution coefficients. User interaction with the program is essential. The program has no capability to determine if the calculated values are consistent with various real restraints. Knowledge of the physical, chemical, and equilibrium behavior is essential to successfully utilize the program. The number of iterations required to achieve steady-state provides insight to the circuit response times. With suitable supervision the program can be used as a simulator for operator training.

Jan 1, 1989

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

A model was developed of a CIL/CIP circuit for recovery of gold and silver. The model uses a simple two rate representation of the leaching kinetics. Parameters for the leaching kinetics may be simply obtained by sampling the feed to a circuit and the tailings from each tank and assaying the solids for both gold and silver to obtain the assay profiles of the solids down the tanks. The parameters in such a leaching model would be expected to be a function of the ore type, the grind, whether oxygen was used and the general chemical environment. These parameters are primary inputs to the model for any simulation. Standard power law relationships are used to express the practical equilibrium between the gold and silver cyanides adsorbed on the active carbon and the tenor of the solutions. The parameters for this may be derived from solution and carbon assays for the same set of samples. The model is constructed by writing a mass balance for gold and silver in and out of each tank in the train and for the circuit overall. Other inputs to a simulation are the feed rate of ore, per cent solids of the slurry in the tanks, gold and silver loadings of the input æbarrenÆ carbon and the rate of movement of carbon through the circuit counter-current to the slurry. With appropriate practical parameters the simulation is able to reproduce typical tank profiles.

Jan 1, 2004

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By James B. Macelwane

THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these 'fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the. January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1952

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By L. A. Bromley, R. L. McKisson

A high temperature calorimeter designed for use up to 1500°K is described and the theory of its operation presented. This calorimeter was used to measure the heats of formation of Na-Sn alloys ranging in composition from tin to Na2Sn. The values tend to support those reported by Kubaschewski and Seith. ONE method of obtaining the heat of formation of an alloy is to measure the heat of mixing of the elements at high temperature. The principal advantage of this method is that the desired quantity is measured directly, while in conventional room temperature methods the differences of the heats of solution of the elements and the alloy in a suitable solvent are measured. A method of improving the accuracy of the high temperature measurements, when the precision of the measurement is lower than that of the heat capacity values for the elements, is to add one component at room temperature to the other at the high temperature, so that part of the heat of reaction is dissipated in heating the cold component to the high temperature. Thus, only a fraction of the heat of reaction is measured, and a result of higher precision is obtained. The limitations of the high temperature technique are that volatile systems cannot be studied, and that many alloys melt at temperatures higher than those at which the calorimetric apparatus operates readily. Nevertheless, a calorimeter operating at 1500°K would be useful in investigating many of the lower melting alloy systems and the low melting mixed oxide systems. A unit designed for these applications was built and is described here. The Na-Sn system was chosen for investigation because the temperature involved, 880°K, would adequately test the operation of the calorimeter. Further, the data reported in the literature for the various alloys of sodium and tin differ markedly, and it was hoped that this investigation would help to fix the values of the heats of formation in this system. Design of Apparatus A detailed discussion of the considerations involved in the calorimeter design is given by Mc-Kisson and Bromley,' and a brief summary follows. Fig. 1 shows a sectional view of the calorimeter. The inner graphite chamber is maintained at constant temperature by means of the circulating molten tin bath in which it is submerged. The tin is contained in a graphite vat. This unit comprises a thermostat whose heat capacity is about 7000 cal per "C. The main heating element consists of a machined graphite spiral with a room temperature resistance of about 1/2 ohm. These parts are separated from the powdered carbon external insulation by the cage, a cylindrical graphite chamber. The electrical insulators and separators, the auxiliary heater spool, and the loading tube liner are made of sintered alumina. The tin vat stirrers, the sample stir-rer, the melt thermocouple well, and the power leads are made of molybdenum. The auxiliary heater is wound with molybdenum wire and serves to compensate for the heat loss up the loading tube. All of the individual components in the high temperature region of the calorimeter will withstand at least 2000°K, and the various contacting materials should easily withstand 1500°K. The external container for the insulating carbon powder is a copper shell upon which copper tubes are soldered to serve as cooling coils.

Jan 1, 1953

By G. Robert Frey

INTRODUCTION This chapter on underground rotary drills briefly describes the equipment features, selection or applica¬tion criteria, safety features, and relative costs of both face and roof drills. After a brief description of the basic components, the application, safety, and cost con¬siderations will be explored. ROTARY DRILL COMPONENTS As illustrated in Fig. 1, an underground rotary drill consists of five basic components. These components are the energy system, chassis, boom, feed assembly, and operator's station. Energy System The energy system of a typical underground drill con¬sists of an electric motor, driving a hydraulic pump or pumps. Usually, the drill is equipped with a cable reel to store the trailing power cable from the portable power center in the mine. A simple control box is supplied to house electrical switchgear and protective devices. In addition to the pump, the hydraulic portion of the energy system includes the hydraulic cylinders, hydraulic tram motors, relief valves, control valves, etc., necessary to actuate the various machine functions. Chassis The chassis provides the frame or support structure for the other four basic components of the drill. Fre¬quently, it incorporates an oil reservoir for the hydraulic system. The chasis provides the support for the trans¬mission, which drives rubber tires or, in the case of some foreign machines, the crawler tracks. The steering link¬age and steering tires also may be considered as parts of the chassis. Boom The boom is the structure that supports the feed assembly; it is either hinged or pivoted on the front of the chassis. Hydraulic cylinders on the boom are used to lift or swing the boom relative to the chassis and to swivel or "roll" the feed assembly. Feed Assembly The feed assembly is made up of the support struc¬ture with an integral thrust mechanism, a rotation unit, centralizers to stabilize the auger, and a hose handling arrangement. In addition, most drills have an extension frame with a tilt device to aid in positioning the feed. Operator's Station The operator's station is the area from which the miner operates the drill. UNDERGROUND ROTARY DRILL APPLICATIONS Underground Face Drills Underground face drills are used in mining opera¬tions that utilize the conventional mining system. The face drill is used to drill holes in the exposed face of the material, and the face is then "shot" by means of explo¬sives or high pressure air. The loose material then is ready for loading and transporting from the face to the preparation plant. Typical specifications for under¬ground face drills are listed in Table 1. Certain parameters should be established as to where the drill is to be used and what is expected of it. To create an awareness of some of the considerations that too often are overlooked, some questions are listed that should be asked in conjunction with the selection or application of the proposed drills. Energy System: Can the drill be supplied with the proper voltage to match the available or proposed elec¬trical power system of the mine? Is the system 250, 460, 500, 550, or 950 v; dc or ac; 3-phase; 60 or 50 Hz? Is the drill equipped with an adequate electric motor to handle the proposed duty cycle? Typical motor power on a single-boom drill would range from 25 to 40 kW (35 to 50 hp); the nominal power for a dual-boom

Jan 1, 1982

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By Paul B. Crawford, Gerald N. Pitts

"A new method is introduced for the simulation by computer of the flow of liquid underground. The method has application in simulating, for example, liquid withdrawal systems, injection systems or injection-well systems. The computer simulation of liquid flow permits the utilization of the known properties of the rock in developing a model of the permeable rock mass.The flow properties of the rock at a specific site arc generated statistically using a random number generator. After defining in this manner the rock properties of each element in the computer grid, the streamlines or flow paths of the liquid are traced using the new method. The simulation is designed especially for computers. The meandering character of the liquids paths is displayed clearly as the fluid moves underground, thus providing the technical information required for the control of the movement of liquid."

Jan 1, 2014

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020