Search Documents

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et&apos; al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4&apos;5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7&apos;8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By J. Orkiszewski

A method i.s presented which can accurately predict, with a precision of about 10 percent, two-phase pressure drops in flowing and gas-lift production wells over a wide range of well conditions. The method is an extension of the work done by Grifith and Wallis and was found to be superior to five other published methods. The precision of the method was verified when its predicted values were compared against 148 measured pressure drops. The unique features of this method over most others are that liquid holdup is derived from observed physical phenomena, the pressure gradient is related to the geometrical distribution of the liquid and gas phase (flow regimes), and the method provides a good analogy of what happens inside the pipe. It takes less than a second to obtain a prediction on the IBM 7044 computer. INTRODUCTION The problem of accurately predicting pressure drops in flowing or gas-lift wells has given rise to many specialized solutions for limited conditions, but not to any generally accepted one for broad conditions. The reason for these many solutions is that the two-phase flow is complex and difficult to analyze even for the limited conditions studied. Under some conditions, the gas moves at a much higher velocity than the liquid. As a result, the down-hole flowing density of the gas-liquid mixture is greater than the corresponding density, corrected for down-hole temperature and pressure, that would be calculated from the produced gas-liquid ratio. Also, the liquid&apos;s velocity along the pipe wall can vary appreciably over a short distance and result in a variable friction loss. Under other conditions, the liquid is almost completely entrained in the gas and has very little effect on the wall friction loss. The difference in velocity and the geometry of the two phases strongly influence pressure drop. These factors provide the basis for categorizing two-phase flow. The generally accepted categories (flow regimes) of two-phase flow are bubble, slug, (slug-annular) transition and annular-mist They are ideally depicted in Fig. 1 and briefly described as follows. RUBBLE FLOW (FIG. 1A) The pipe is almost completely filled with the liquid and the free-gas phase is small. The gas is present as small bubbles, randomly distributed, whose diameters also vary randomly. The bubbles move at different velocities depending upon their respective diameters. The liquid moves up the pipe at a fairly uniform velocity and, except for its density, the gas phase has little effect on the pressure gradient. SLUG FLOW (FIG. 1R) In this regime, the gas phase is more pronounced. Although the liquid phase is still continuous, the gas bubbler coalesce and form stable bubbles of approximately the rame size and shape which are nearly the diameter of the pipe. They are separated by slugs of liquid. The bubble velocity is greater than that of the liquid and can be predicted in relation to the velocity of the liquid slug." There is a film of liquid around the gas bubble. The liquid velocity is not constant—whereas the liquid slug always moves upward (in the direction of bulk flow); the liquid in the film may move upward but possibly at a lower velocity, or it may move downward. These varying liquid velocities will result not only in varying wall friction losses, but also in a "liquid holdup" which will influence flowing density. At higher flow velocities, liquid can even be entrained in the gas bubbles. Both the gas and liquid phases have significant effects on the pressure gradient. TRANSITION FLOW (FIG. 1C) The change from a continuous liquid phase to a continuous gas phase occurs in this region. The liquid slug between the bubbles virtually disappears, and a significant amount of liquid becomes entrained in the gas phase. Although the effects of the liquid are significant, the gas phase is more predominant.

By Georg Unland, Thomas Wegner

"Impact crushers are widely used in different industries to crush materials which can vary from soft to hard and from ductile to brittle. However, the sizing of impact crushers is still based rather on empirical than on scientific approaches. Therefore, a test rotor was developed in order to investigate the principles of comminution by impact. Rocks of diabase with different diameters were used to gain the crushing properties with the following results:RESISTANCE AGAINST CRUSHINGLikelihood of BreakageThe likelihood of breakage is a function of the impact velocity and the particle diameter. The likelihood increases with higher velocities and larger diameters. Maximum Crushing ForceThe crushing force is related to the area of projection of the rock. The smaller the particles and the higher the velocities the larger are the maximum related contact forces.Contact TimeThe contact time increases with the rock diameter whereas the influence of the impact velocity is neglectable.Mass Specific Crushing WorkThe mass specific crushing work decreases with the particle diameter and increases with the impact velocity."

Jan 1, 2003

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By Nico Van Wingen

Experiments performed with distilled water, unconsolidated sand and dead oil for the purpose of determining the influence of oil flow on the water content of sands were described. While results found are not necessarily, therefore, identical with those that would be obtained under natural petroleum reservoir conditions, the following conclusions were drawn. 1. When oil under constant head is flowed through an unconsolidated sand, the amount of water retained in the core is inversely proportional to the specific permeability of the core. This corroborates the view that the degree to which oil displaces water out of the pore space is limited by the size of the pores. 2. For the range investigated, the displacing action of a more viscous oil of higher specific gravity was found to be the same as a less viscous oil, or lower specific gravity. 3. The amount of interstitial water retained in the sand bears an inverse relationship to the pressure head of the displacing liquid. 4. The degree of retained water saturation of the sand appears to approach 100 per cent as the specific permeability approaches zero. 5. For the higher values of specific permeability and for the pressure range investigated the remaining amount of water in the sand occupies approximately 10 per cent of the pore space. This, together with the fact that the limiting oil velocity curve approaches approximately 10 per cent water saturation as an asymptote, indicates that beyond this point removal of water is achieved only by a stripping of the grains requiring considerable pressure drops across the sands; or by a balancing of the molecular forces. 6. As the water saturation of the sand exceeds approximately 15 per cent of the pore volume, the permeability of the sand to oil decreases rapidly. 7. Sands with water saturations as high as 40 per cent were found to produce 100 per cent oil.

Jan 1, 1939

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Paul Merica

ONE of the most useful, and at the same time least commonly used, methods of thermal analysis for the determination of transformations in metals and alloys consists in the recording of the tune intervals required for successive increments of temperature change during heating or cooling, the temperature of the furnace containing the specimen being altered at a uniform rate. The curve obtained by plotting these time intervals as a function of the mean temperature of the specimen during the interval is called the inverse-rate curve. It is probably due to the fact that no simple and convenient method has apparently been available for the measurement of the successive time intervals that this method has not been so generally used as, for example, the differential method, for which several tykes of automatic or semi-automatic apparatus have been designed. Whenever this method has been used, the intervals have usually been measured with the use of a chronograph; its operation as practised at the Bureau of Standards&apos; is as follows: The temperature of the specimen is measured by a thermocouple and a dial potentiometer. The operator sets the potentiometer at successive values of the electromotive force differing by equal increments, usually 0.02 millivolt, and records the exact instant on the chronograph, by pressing a contact key, at which the galvanometer coil passes through its null position. Two-second intervals are also recorded on the chronograph record, and the number of &apos;seconds elapsing between successive signals is afterward counted from the record and plotted as a function of the electromotive force or of the temperature. This is an admirable method and by it most minute thermal arrests may be detected, but it requires a good chronograph, which is generally difficult to obtain, and the time of one operator during the recording and, subsequently, to read the intervals from the record; the latter operation often takes from one to two hours.

Jan 7, 1919

On 8th August, 1973, 57 members of the Institute visited Prieska Copper Mine at Copperton in the North Western Cape. After tea, the group was welcomed by the Management of the Mine, and Mr Grobler, the General Manager, gave an introductory talk. After they had been taken on a bus tour of the property, the members split up into groups and proceeded underground or to the concentrator. Of special interest to the mining members were the rock-handling methods in use at the mine. The stoping method that has been adopted is the continuous, long-hole sub-level open stoping system. The broken ore is moved with rubbertyred front-end loaders from the stope drawpoints to the ore passes. On the main tramming levels, the ore is collected by electric locomotives and discharged into the main shaft system at the bottom. At the shaft ore-pass system, a gyratory crusher that can accept rocks up to 1 m in diameter has been installed. The crushed product (minus 150 mm in diameter) will then be hoisted by a Koepe winder, which has a rated capacity of 900 tons per hour. The mine is also served by a declined roadway from surface, which facilitates the movement of heavy equipment. The most striking aspect is the productivity that can be achieved by the use of a trackless-mining system. For the production of 230 000 tons per month, it is estimated that 6 stopers and 7 developers will be required. The total labour force will be approximately 2500-2000 Bantu, 200 Coloured, and 300 Europeans. Training of maintenance and operating personnel is of the utmost importance, and it was interesting to note the extent to which non-White labour is being used in these occupations. Lunch was served at the single quarters, after which the group proceeded to the airfield for the return trip to Johannesburg. On behalf of the visitors, Professor de V. Lambrechts thanked Mr Grobler and his staff for the most interesting morning and for their hospitality,

Jan 10, 1973

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By Edward H. Robie, E. J. Jr. Kennedy

his volume records the "clay symposium" that featured the geology side of the Annual Meeting of the Institute at St. Louis, February 19-22, 1951. The symposium consisted of four sessions held under the joint sponsorship of the Geology Subdivision and the Industrial Minerals Division AIME and the Society of Economic Geologists. Its main purpose was to define or outline certain problems of clay and laterite genesis, and the papers herein, which were presented at the first three sessions, deal for the most part with individual deposits or special problems. The fourth session was a seminar concerned almost wholly with a discussion of "problems." The discussion follows the papers in the volume. The clay symposium was not the work of an appointed committee. It was thought up and inspired by John J. Collins, who so ably supervised and co- ordinated the mining, geology, and geophysics program for the 1950 annual meeting of the Institute. After requesting Dr. A. F. Frederickson to get material together on clay and laterites for the St. Louis meeting, Mr. Collins visited Dr. Frederickson and discussed this project with him in greater detail. By that time their interest and enthusiasm had spread to others in the field. The Geology Subdivision, the Industrial Minerals Division, and the Society of Economic Geologists by common consent turned over the organization of the program to Dr. Frederickson. Mr. Collins continued in active touch with Dr. Frederickson and gave him every assistance. Dr. E. C. Harder and Dr. W. D. Keller read all the material comprising the symposium, and their comment was made available to Dr. Frederickson, who did much to put papers and discussion in final shape for publication. To the Karl Eilers Memorial Fund--one of the Funds that enables the Institute to publish books of this kind, to the authors of the various papers, to the contributors to the discussion, and to Messrs. Collins and Frederickson the Institute and readers of this book are indebted.

Jan 1, 1952

A metallurgical balance drawn around a mineral processing plant or smelter must involve all process streams crossing the plant boundary. Modern sampling theory, as formulated by Gy, and sound statistical method can be used to determine the uncertainties in the observed assays for the set of balance analytes and in the mass flow rates of the process streams for the balance period. These uncertainties can then be used together with the material balance equations to arrive at adjusted component mass flows that satisfy the material balances exactly. To determine whether or not the data is consistent with the level of uncertainty in the data and with the material balance equations, a goodness of fit test is applied. This goodness of fit criterion is the principal tool to quantify the quality of the material balances. The mathematical structure of the statistical material balance problem poses a number of challenges. For example, while the variances of the adjusted component mass flows do not vanish, the variances of the sums of the adjusted component mass flows about each balance node do vanish, simply because the balancing computation demands that the balances close exactly. Even though it can be shown that the variances of the adjusted component mass flows are always lower than the estimates for the corresponding unadjusted component flows, it is still not possible to construct a confidence interval on the component mass flow into (and out of) a balance node using the adjusted component flows. On the face of it, such a confidence interval is exactly what is most desired from the balance calculations. The problem arises because the balance problem is a data adjustment rather than a parameter estimation problem. It is possible, however, to calculate the recovery of a component to a product stream and determine a confidence interval for the recovery value. It is also possible to calculate an uncertainty in the mass flow of any balance species in any process stream, before and after balancing.

Jan 1, 2005

By S. R. Elliott

THE Spies mine is located in the eastern half of the northwest quarter of section 24-43-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in, open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope.

Jan 3, 1922

By F. W. Miller

Prior to the Civil War, there were several small charcoal furnaces for smelting the brown limonite ore that is found, in comparatively small bodies, throughout the central and north-central portions of the state. During the Civil War, these furnaces furnished charcoal iron to the Confederate Government. No attention was paid to the large bodies of lime-bearing hematite ore that now supplies the bulk of the ore used in the various blast-furnace plants of this district until the latter part of the 19th century. Red Mountain, which is the southernmost and one of the smaller ranges of the Appalachian Chain, lying immediately south of the Birmingham and Bessemer, is the principal source of this ore. The orebody outcrops on the northern face, extends through the mountain, and underlies Shades Valley on the southern side. When it was found that these ores could be worked satisfactorily in the blast furnaces, there was a comparatively rapid growth in the blastfurnace industry in the Birmingham district. As these ores are far more refractory than the limonite ores, this blast-furnace development was accompanied by the construction of beehive ovens to carbonize the coal, in order to supply the necessary fuel. The state&apos;s production of beehive coke in 1880 was 60,781 tons; ten years later this had increased to 1,072,942 tons; and, in 1897 the production had reached 1,443,017 tons. In 1898, the first byproduct oven built in the state was put in operation. This plant consisted of 120 horizontal-flue Semet-Solvay ovens, three flues in height by thirty flues in length with an average width of 16 in. The plant was constructed by the Semet-Solvay Co., for the Tennessee Coal, Iron & Railroad Co., and was located adjacent to the blast-furnace plant of that company at Ensley. Coal was delivered from the Pratt mines, by gravity tracks, directly into bins of the ovens after having

Jan 1, 1925

Reply to discussion of the paper of C. W. Washburne, presented at the New York meeting, February, 1914 (Trans., xlviii, 687 to 694 (1914)). C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Professor Lane makes an interesting contribution to the study. of chloride waters, in saying that calcium chloride waters occur not only in the greenstones of the Lake Superior copper mines, but also in the interbedded -felsitic conglomerates and "in far-removed sandstones, e.g., near Whitefish lake, and Ontonagon, in the Michigan iron mines, and in the Storm King granite." Surely these are not connate waters preserved from the Algonkian sea, assuming that the Algonkian sediments are marine rather than continental. Finding the same type of water in the Storm King granite points rather toward an abyssal source. The possible connection of these waters with the magma of the greenstone is immaterial, although some basic calcic magma is the most probable source. It is to be expected that the ascending water of the region would be found not only in the greenstones, but in all the rocks which it could penetrate. The ascent of water of this kind along vertical passages, and the consequent addition of a common ion: to the circulating sedimentary salt solutions, would explain the precipitation and localization of the "giant, concretionary" salt plugs of the Gulf Coast, without making the ex-excessive demand for an improbable quantity of salt in the adjacent sediments that is required by the unmodified theory of Harris. With-out such a precipitating medium most of the dissolved sodium chloride would have been lost by passing on to the surface without precipitation. The base to which the chlorine ions were attached is immaterial, providing they were sufficiently concentrated, but the presence of the chlorides of calcium and magnesium in the solutions is indicated by the associated bodies of secondary dolomite.

Jan 4, 1915

By M P. Schwarz

In recent years, computational fluid dynamic (CFD) modelling of mechanically stirred flotation cells has been used to study the complexity of the flow within the cells. In CFD modelling, the flotation cell is discretised into individual finite volumes where local values of flow properties are calculated. The flotation effect is studied as three subprocesses including collision, attachment and detachment. In the present work, these subprocesses are modelled in a laboratory flotation cell. The flotation kinetics involving a population balance for particles in a semi-batch process has been developed. From turbulent collision models, the local rates of bubble-particle encounters have been estimated from the local turbulent velocities. The probabilities of collision, adhesion and stabilisation have been calculated at each location in the flotation cell. The net rate of attachment, after accounting for detachments, has been used in the kinetic model involving transient CFD simulations with removal of bubble-particle aggregates to the froth layer. Comparison of the predicted fraction of particles remaining in the cell and the fraction of free particles to the total number of particles remaining in the cell indicates that the particle recovery rate to the pulp-froth interface is much slower than the net attachment rates. For the case studied, the results indicate that the bubbles are loaded with particles quite quickly, and that the bubble surface area flux is the limiting factor in the recovery rate at the froth interface. This explains why the relationship between flotation rate and bubble surface area flux is generally used as a criterion for designing flotation cells. The predicted flotation rate constants also indicate that fine and large particles do not float as well as intermediate sized particles of 120 - 240 ¦m range. This is consistent with the flotation recovery generally observed in flotation practice. The magnitude of the flotation rate constants obtained by CFD modelling indicates that transport rates of the bubble-particle aggregates to the froth layer contribute quite significantly to the overall flotation rate and this is likely to be the case especially in plant-scale equipment.

Jan 1, 2005

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942