Search Documents

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By H. M. Howe

A Discussion of the paper of Professor Howe, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 14, March, 1907, pp. 169 to 274. SECRETARY'S NOTE.-M. Beutter's introductory remarks, being simply a resume of Prof. Howe's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution has been somewhat condensed, without omitting any essential statements. M. BEUTTER, St. Etienne* (communication to the Secretary-+):-Professor Howe observes in paragraph 47 of his paper that the fluid-compression of steel. diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingworth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forgings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without dan¬ger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jul 1, 1907

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By R. E. Head

"The microscopic work described below was engaged in primarily into ascertain the approximate proportions in which the copper sulphides existed in the ore examined, and by a comparison of the results obtained from a study of both head are tailing samples to supply data which might be of value in treating the ore by flotation. Incidentally, the physical characteristics and association of the sulphides were noted in order to determine the possible relation or bearing of these features on the present conditions of treatment. Since the copper in the ore occurred as three distinct sulphide minerals - chalcopyrite, chalcocite, and bornite each containing copper in different proportions, there appeared to be little or no possibility of obtaining the desired information by chemical methods of determination.Type of material examinedThe material examined was in the crushed condition and was said to be representative of the flotation feed or heads and the resulting tailing. No hand samples of the ore were examined nor any account taken of the physical condition and association of the minerals in place, because the possible value of the analytical results depended on conditions as they existed in the crushed ore. As the problems under consideration dealt only with the sulphide minerals, especially those of copper, the products from screen sizing were concentrated by hand panning and the gangue discarded. The concentrate obtained consisted almost entirely of the sulphide minerals, since the panning had been very carefully done. The object of this procedure was to obtain a sufficient quantity of high-grade sulphide material, from the sample of each screen size selected for examination, to permit its being so prepared for examination as to be representative of the physical characteristics exhibited by a large number of sulphide grains from each respective size, In the tests and investigations carried on by the company' treating the ore the following sizes had been used in tabulating data and basing conclusions:+48, +65, +100, +150, +200, and -200. These same sizes were used in the microscopic investigation, since the results obtained thereby could be most readily utilized for comparison with the results obtained in previous experimental work, together with deductions based on actual concentration of the ore on a commercial scale."

Jun 1, 1921

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By Bruce Vandenberg, R F. Chiappetta

"The High Speed 2D Analysis program allows the user to bring in data from several different sources. Of course, keyboard entry is included as a source. Other data is inputted through the serial port (X-2321 of the PC. Two types of data are transferred via the serial port. The first is the tablet digitizer data. The three types supported presently are the GTCO, tablet digitizers. and the Calcomp 2500 and 9100 series To transfer digitized data turn on the selected digitizer and place the cursor on the tablet. Enter the High Speed pmg.ram and select from the Input Program menu the Digitize Inputs(20) option and follow the instructions. TO exit the session, either a keyboard entry or a cursor button is pressed. The second type of serial port input Is from the collectors of the listed survey systems. Typically a file transfer program will be used to send the data from the collector to the PC. This topic will not be addressed at this time."

Jan 1, 1989

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

James Gayley, Braddock, Pa. (communication to the Secretary) : Mr. Potter has made reference to our practice at the Edgar Thomson works in the direction of increasing the life of the lining, and mentions the product of one of our furnaces as having reached a total of 370,000 tons. It may be interesting to know that this furnace has been put out of blast with a record of 452,685 tons, after a run of three years and nine months. A companion-furnace to this will produce, hefore the present year is ended, half a million tons. As Mr. Potter has quite correctly designated this as " the newest problem in furnace-practice," a description of the construction of this furnace lining may be Welcome to members. The bricks used in the lining are 9 and 134 inches long, with the requisite quantity of straight and key-shapes to turn the circle. There bricks are well suited for enclosing the numerous bosh-plates used for cooling. The bosh-plates (the efficient fortress of the lining) extend from the top of the tuyere arch to the mantel, and are inserted in rows, 18 inches to 2 feet apart. These form a perfect defence against encroachment on the bosh-lining, and leave the bosh at the end of the blast of the same thickness as at the beginning. The protection afforded by these bosh plates is the principal cause of the increased duration of the furnace-lining. But it must be noted that the shape and material of the plate are essential elements. The most serviceable plate is that made of bronze or copper. We have tried every form of iron plates without obtaining satisfactory results. These were replaced with bronze plates, built into the lining, which gave excellent results so long as they did not leak; but when this occurred, as it did in time, the water was shut off, and, since the plates could only be removed with difficulty, they were allowed to burn off. This permitted encroachment on the bosh-walls, which thus became enlarged beyond the limit required for economical practice. With the introduction of the removable plate, made tapering on the sides, with plain surfaced top and bottom, these troubles have

Jan 1, 1895

By Lawrence Devon Smith, Keith Spence, William Roscoe

"In March 2003 the CIM Council adopted and approved the document “Standards and Guidelines for Valuation of Mineral Properties” as developed by the Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum on Valuation of Mineral Properties (CIMVal). The document is referred to as the CIMVal Standards and Guidelines. The document evolved from a specific recommendation by The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) that the CIM form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties. The CIMVal Standards and Guidelines are organized into two parts: •,Standards which are general rules in the Valuation of Mineral Properties. The use of the Standards is mandatory if the Valuation Report is stated to follow CIMVal (although not mandatory in the sense of having regulatory authority). Definitions are given at the beginning of the Standards. •,Guidelines which elaborate on the Standards and, while not mandatory, provide guidance and best practices which are highly recommended to be followed in the Valuation of Mineral Properties.CIMVal specifies requirements for the Qualified Valuator who has the responsibility for choosing the appropriate approaches and methods for the valuation of mineral properties. With regard to the specifics of the application and practice of valuation approaches and methods, CIMVal directs the Qualified Valuator to the large body of published papers, published valuations, presentations and court judgments to guide his or her choice. This is also the approach taken by VALMIN (Australia) and SAMVAL (South Africa). To facilitate the dissemination of industry practice, the CIMVal Committee organized a “Valuation Day” at the CIM Annual General Meeting in Toronto (Mining Millennium 2000), on March 8, 2000. Industry experts presented papers on valuation of Mineral Properties which were subsequently published in a proceedings volume and individually ad technical papers in the CIM Bulletin. The Management and Economics Society of CIM has continued to identify and publish papers on valuation in the CIM Bulletin and Magazine. The present document gathers in one place the CIMVal Standards and Guidelines, the papers from the 2000 Valuation Day, and a number of subsequent papers that illustrate industry practice for the valuation of mineral properties."

Jan 1, 2003

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By T. J. Jr. DeMull, F. G. Miller, J. P. Matoney

For some time a need had existed in the minerals processing field for a relatively efficient separator that would treat high tonnages of particles in the intermediate size range, i.e., those particles too large for froth flotation and too small for conventional gravity-type separa¬tors. Among those devices developed to meet this need are the centrifu¬gal specific gravity separators. These devices employ centrifugal acceleration to assist gravitational acceleration in separating light¬density minerals from heavy-density minerals. In the category of centrifugal specific gravity separators are the heavy-media centrifugal separator and the water-only cyclone. The two major centrifugal heavy-media separators, i.e., the heavy-media cyclone and the DynaWhirlpool, as well as the water-only cyclone, are discussed in terms of: design features, operating variables, operat¬ing data, and flowsheet design criteria. Examples of plant applications are given in the field of coal processing as well as the processing of other minerals such as iron ores, potash, and tin. Finally, the subject of the staging of centrifugal separators and their use in combination with other separators is discussed. PRINCIPLES For coarse sizes of minerals, efficient specific gravity separations have been possible for many years with open-bath vessels using the natural settling velocity or buoyancy of the particles. These bath ves¬sels process ore by utilizing micron-size solid particles suspended in the slurry fed to the separator. The inclusion of these particles in the slurry increases the effective density of the separating fluid to allow particle separations to be made at densities greater than that of water. However, if vessel size is to remain within economical limits, the particles processed in the bath vessel must have high settling rates in a IG gravitational field. Because of this requirement, heavy¬medium bath vessels are usually restricted to processing +V4-in. sizes. To extend efficient specific gravity separation to smaller sizes, the gravitational acceleration of particles is replaced by centrifugal acceleration. The settling of a small particle in a fluid in a centrifugal force field is similar to that found in a static bath except that the acceleration due to gravity, g, is replaced by a centrifugal acceleration where v, is the tangential velocity at radius r: V=kdm(P-P,), V'. (J) µ In more practical terms where the particles settle in a suspension of finer particles comprising the heavy media and with an effective suspension density p" V = kdm' (P P ) . v'. (2) U r To date the most effective use of this principle has been obtained with devices that rotate a liquid or suspension within a stationary enclosure in order to create centrifugal force. Cyclones are the most common devices used for this purpose, because they generate centrifu¬gal forces far greater than the force of gravity and therefore not only have high capacities but can treat finer sizes than bath-type vessels can. The two main types of cyclones used by industry are the heavy-media cyclone and the water-only cyclone. Also quite widely used is the DynaWhirlpool, which, though based on the same princi¬ple, differs in design from the conventional cyclone. HEAVY-MEDIA CENTRIFUGAL SEPARATORS Like the bath vessels, the heavy-media centrifugal separators em¬ploy media composed of micron-size particles suspended in water. However, the centrifugal force generated in these separators accentu¬ates the difference in settling rate between particles of different density and thus makes possible separations of finer size particles than can be treated in bath vessels. The two most common heavy-media centri¬fugal separators are the heavy-media cyclone and the DynaWhirlpool. Heavy-Media Cyclone Although cyclones were originally developed for use as classifiers or thickeners, it was later found that they could also effectively serve as heavy-media separators.63. 64, Design Features Fig. I I is a schematic of a typical cyclone developed to serve for any one of the following purposes: as a classifier, thickener, or specific gravity separator. The cyclone consists of a cylindrical section joined to a conical section, usually having an included angle of between 14° and 25°. Feed enters the cyclone tangentially through an orifice attached to the cylindrical section. The overflow orifice is located in the base plate of the cylindrical section. The vortex finder, a tube attached to the overflow orifice, extends into the cyclone from the base plate of the cylindrical section. The underflow orifice is located at the apex of the conical section. As some medium together with mineral particles is fed through the feed orifice, a vortex with a hollow air core extending from the overflow to the underflow orifice forms in the cyclone while hollow spray discharges form at each of these orifices. Under the influence of the centrifugal force, high specific-gravity particles move through the medium to the wall of the cyclone and descend in a spiral flow pattern to the underflow orifice. Those particles in the feed stream, lower in specific gravity than the feed medium, follow the major portion of the flow to the center of the core where they are caught in the high-velocity upward central current and are carried out through the overflow orifice. Fig. 12 shows a family of curves that illustrates how materials of varying specific gravity are recovered by a cyclone. Since the specific gravity of the medium is 1.40, the particles of 1.40 sp gr actually act as part of the medium and, regardless of the particle size, split between the underflow and overflow of the cyclone in proportion to the volume split of the medium. Particles higher in specific gravity than 1.40 are recovered in the underflow of the cyclone at increasing rates as the difference in specific gravity increases and the particle size increases. Particles lower than 1.40 in specific gravity are dis¬charged through the overflow orifice at increasing rates as the specific¬gravity difference increases and the particle size increases. However, all the curves originate at the fluid-flow ratio point for the finest particles of any gravity. The fluid-flow ratio is defined as the ratio of the rate of fluid flowing from the underflow to the rate of fluid

Jan 1, 1985

By Don Suttie, Frank Roybal, John Wright

The Roybal Raise incorporates the simplicity and low cost of a short bald-headed raise while overcoming the usual impediments to driving a high baldheaded raise. The concept provides for speedy excavation and maximizing the use of the excavated opening, using the rock for structural support. The design is simple: two baldheaded raises are driven parallel to one another, interconnected by dogholes about 8 m (25 ft) apart. In this fashion, the raise can be driven safely and efficiently to 60 m (200 ft) or more. When the raise is complete, the excavation requires no timber for support or partitioning. Rather, the rock itself supports the construction. As a test, a two-compartment Roybal Raise was attempted at the Independence mine in the Willow Creek District of Alaska. One side was driven 2 x 2 m (6 x 6 ft), intended for a manway and equipment skip. The other was driven 1.5 x 1.5 m (5 x 5 ft) for a muck compartment. Both sides were driven at a 65° angle from horizontal and 1 x 1 m (4 x 4 ft) dogholes spanned the 4.6-m (15-ft) pillar between the two compartments. After topping out at 50 m (160 ft), the raise was found to meet all expectations of efficiency, low cost, and practical simplicity. Technique Preparing the Roybal Raise for driving involves no elaborate or costly site prep except assembling materials and providing for muck removal. Normally, the raise muck falls directly onto the sill or track and is picked up either by an overshot mucker or a front-end loader. Raise mining proceeds initially by taking up both compartments simultaneously to the first doghole. It progresses by alternating one side as a clear manway for access with the other side, the active side, as a muck compartment (Fig. 1A). This stage proceeds quickly for no mucking or staging is required to cycle the first three rounds. On the fifth round, in addition to the normal raise round, rib holes are winged out toward the adjacent raise, thus starting the dogholes. Finally, as the sixth raise rounds are drilled and shot, the first doghole is also completed from both sides. The second stage commences by establishing one side as a clear manway for access while the other side, used as a muck compartment, is prepared for active mining. Figure 1B illustrates this step in the succession of raising with the active side advancing to the second doghole level. During this stage, services are maintained through the manway side and equipment is stowed in the doghole during blasting. As the active side advances, muck may be allowed to fill the bottom portion of that side since it is unnecessary to clear it for access. The next stage of raising involves cleaning out the former muck compartment and preparing it for use as a manway. At the same time, the former manway is prepared for advance and use as a muck compartment (Fig. 1C). As in the previous step, the same doghole is used for access and equipment storage. The active side advances until the second doghole is completed, at which point equipment and access are moved to the new doghole. From there, the active side is driven past the second doghole 8 m (25 ft) more to the third doghole level. Again, half of the doghole and the next raise round are mined. The fourth stage involves switch ing back the manway side for the muck side (Fig. ID). The new muck side is driven to the third doghole where equipment storage and access are reestablished. From there, the active side is advanced to the fourth doghole. In the same fashion, the raise is advanced to the top, alternating the manway side with the active side, maintaining access through the inactive manway, and storing equipment in the uppermost doghole. The cycle time for driving each compartment, regardless of the raise height, is greatly improved over that for normal bald-headed raises of comparable height. By storing equipment in the upper-

Jan 1, 1984

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982

By T. C. Atchison, W. I. Duvall

Over the past ten years a series of investigations have been conducted to determine some of the pnysical processes involved in breaking rock with confined concentrated charges. Detailed discussions of many of these investigations have been published elsewhere.1-6 Laboratory experiments made by other investigators using Hopkinson pressure-bar techniques have shown that solid materials are fractured in tension by the reflection of an incident compressive stress pulse at a free surface.7-12 In these tests a small charge of explosive is placed in contact with one end of a bar. Detonation produces some plastic flow and crushing of the bar near the charge and generates a compressive stress pulse that travels along the length of the bar. At the free end of the bar the compressive stress pulse is reflected back into the bar as a tensile stress pulse. If the tensile strength of the bar is exceeded during this reflection process, a tensile fracture normal to the length of the bar is produced, and the broken end of the bar moves forward with a constant velocity equal to the average particle velocity trapped in the broken fragment. The new surface formed by the fracture becomes the new free end of the bar that reflects the remaining portion of the incident compressive stress pulse. This process is repeated any number of times until all of the incident stress pulse is reflected. Hino has demonstrated this kind of breakage for three rock types—marble, granite, and sandstone." He has defined a blastibility coefficient, B, as the ratio of compressive strength, C, to tensile strength, T, thus: C The quantity B is the maximum number of slabs that can be produced by reflection breakage. Normally fewer slabs are produced because of loss of energy as the stress pulse travels through the rock. Fig. 1 illustrates reflection-type fracture for a triangular compressive stress pulse. The number of slabs produced by the reflection breakage process is the first whole number less than the ratio of the peak stress of the incident pulse to the tensile breaking stress of the solid. Thus the number of slabs is given by the thickness of each slab is given by and the total length of rock broken is given by N = number of slabs S - peak stress in incident pulse T = tensile strength of the rock F = fall length of incident stress pulse h = thickness of each slab D = total length of rock broken During the reflection process the particle velocity at the free surface is twice the particle velocity in the incident stress pulse. Thus the velocity with which the broken fragments move forward is given by where v, = velocity of broken fragment, and v = average particle velocity contained in that portion of the incident pulse trapped in the broken fragment. Results of these laboratory experiments cannot be applied directly to rock blasting where the explosive charge is placed in a drillhole. In laboratory tests the charge is unconfined and in contact with the rock in only one direction. In a drillhole additional confinement is offered by the rock surrounding the charge and by the stemming placed above it. This additional confinement may be enough to allow the explosive gases to do additional work on the rock during their expansion. Other writers have discussed possible effects of gas expansion'on rock breakage.13-10 However, very few experimental data are available to determine to what extent expansion of the gases is responsible for rock fragmentation. The USBM has studied the physical processes involved in breaking rock with confined concentrated charges by using simple crater tests breaking to one free surface. Crater tests have been performed in four rock types: granite, sandstone, marlstone, and chalk. Table I gives some physical properties of these rocks. Fig. 2 shows plan and section drawings of two typical crater tests and illustrates some of the test variables measured. For these tests the charge was placed at the bottom of the drillhole and primed with an electric cap. The hole was stemmed to the collar with sand and the charge detonated. Size and shape of the crater were measured after it was cleared of broken rock. As a given charge size was buried deeper in a drillhole, the crater depth usually was equal to or

Jan 1, 1960

By Richard H. Bube

Photoelectronic radiation detectors may be conveniently classified as homogeneous intrinsic, homogeneom extrinsic, or junction type. Highly photosensitive homogeneous intrinsic photodetectors may be prepared from a number of different II-VI, III-V, or IV materials. Such materials require the presence of specific imperfections that can act as sensitizing centers to provide long majority carrier lifetime. Homogeneous extrinsic photodetectors are of interest primarity for infrared detection, and consist principully of germaniuim and silicon with suitable inpurities. A vaviety of junction photodetectors exist, with silicon us the most common material for them all. The following extrema in performance are found: 1) highest photoconductivity gain in homogeneous intrinsic photodetectors; 2) smallest response time (highest frequency response) in p-i-n junctions; 3) largest gain-bandwidth product in avalanche diodes. ALTHOUGH the total number of materials exhibiting photoconductivity effects is very large, only a relatively few of these have appropriate properties for a practical photoelectronic radiation detector. In fact if one surveys the commercial detectors currently available, one finds that the field is dominated by some ten or fewer materials. These are summarized in Table 1 in terms of the other important variable in detector fabrication, the structure of the material, i.e., whether the material is used as a single crystal or in polycrystalline form, and whether the material is used as a homogeneous detector or whether the detector depends upon the existence of a junction or barrier in the material. The principal wavelength range for each type of material is also shown, together with an indication of the utilization of intrinsic or extrinsic excitation. For the purposes of the present comparison of various detectors, it will be convenient to discuss two main topics: homogeneous photodetectors and junction photodetectors. The performance of a photoelectronic radiation detector is measured in terms of two parameters: the photoconductivity gain, and the response time of the detector. A convenient figure-of-merit is given by the ratio of gain to response time, often called the gain-bandwidth product. The photoconductivity gain is a device parameter since it varies in many cases with the applied voltage and the detector geometry, and should be distinguished from the actual photosensitivity of the material involved. This photosensitivity can be conveniently given as the product of free carrier lifetime and mobility in the material. The photoconductivity gain is defined as the number of charge carriers which pass between the electrodes per second for each photon absorbed per second, where G is the photoconductivity gain, is the pho-tocurrent in amperes, e is the electronic charge in coulombs, and F is the total number of electron-hole pairs created in the photo conductor per second by the absorption of light. The gain may also be expressed as the ratio of the lifetime of a free carrier to the transit time for that carrier, i.e., the time required for the carrier to move between the electrodes. For a material in which one-carrier conductivity dominates, where T is the lifetime of a free carrier, ttr is the transit time for this carrier, p is the carrier mobil-ity, V is the applied voltage, and L is the electrode spacing. From Eq. [2] it follows that the photoconductivity gain is proportional to the photosensitivity of the material (tP), the proportionality constant being The photosensitivity of a material, and hence the photoconductivity gain of a device utilizing the material, depends on the lifetime of the free carriers as a critical parameter. In a homogeneous material this lifetime is determined by the nature of imperfections in the material, and in an inhomogeneous material the lifetime is determined by the specific junction structure. The speed of response, the other basic photodetec-tor parameter, is determined by factors quite similar to those important for photoconductivity gain. Imperfections are of primary importance in homogeneous materials, and the structure of the junction is a determining factor in junction devices. For infrared detectors it has become common to define another quantity designed to indicate directly how effective the detector is in distinguishing between a small photoconductivity signal and random noise due to the detector and its environment. The detectivity D* is given by

Jan 1, 1968

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By K. C. Strebig, C. W. Schultz, A. A. Selim

For some time researchers have attempted to in- crease drilling efficiency (and therefore reduce costs) by adding certain chemical agents to the circulating medium. The effect of some organic additives on the diamond drilling of quartzite was recently investigated in the laboratory by personnel of the U. S. Bureau of Mines. In these tests, the penetration rate and bit life were found to increase with the use of additives. In addition, an economic analysis of a hypothetical 1000-ft hole showed that additives can reduce drilling costs by 30%. Wetting Agents Improve Drilling Efficiency Much of the interest in the use of wetting agents to improve drilling efficiency is the result of an observation made by Rehbinder, Shreiner, and Zhigach.1 These investigators postulated that drilling creates a region of increased crack formation directly below the bit and that a circulating medium that wets the rock will also penetrate the micro- cracks of the predestruction zone. Increasing the molecular affiinity (wetting ability) of these circulating media for the surface of the rock helps the deformation and destruction by softening the rock in the zone of increased crack formation. In this manner, the hardness or strength of the rock is decreased as the medium wets the rock in the predestruction zone. This is known as the "Rehbinder effect." Rehbinder's work has prompted many investigators to examine the relationship between the use of additives and the mechanical destruction of rock. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the mineral and solution interface.2 Improvement in rock breakage with the use of additives was observed by Frangiskos and Smith.3 Joris and McLaren suggest that additives having a lower surface tension than water will also be more efficient in cooling the diamonds.4 Additives help remove fine cuttings from the face of the bit and improve efficiency. The latter two authors also report an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. All of these investigations were initiated in the hope of discovering what economic benefits will accrue with the use of additives.

Jan 10, 1969

By S. R. Elliott

THE principles of the caving system, as they apply to mining of soft iron-ore deposits, are well known, as this method has been in use for many years. It is, however, necessary to give a general description of it before describing the Athens method. The shaft and surface equipment should be placed at a sufficient distance from the orebody, so that the caving and pulling of the surface will not disturb the operations of the mine. Levels are started at the proper intervals, and when raises are completed, slicing commences at the top of the orebody and progresses downward. The necessary precautions are taken to avoid the occurrence of large open rooms and it is customary to break sufficient capping to form a mat to prevent heavy falls of ground from crushing through to the lower sublevels and endangering the lives of the workmen. Slicing is continued, and when sufficient width and length are undercut, the capping commences to cave, and in time a settlement occurs at the surface. As soon as this caving commences, the pressure on the timber naturally increases; after it extends to the surface, the amount of pressure has a certain relation to the depth. In other words, the pressure increases with the depth, but not in direct proportion. At great depths, such as that found at the Athens, 2500 ft. (760 m.), the pressure might be so excessive that the cost of keeping working places open would be prohibitive. The actual caving of the surface in a deep mine, with a great thickness of capping, is slow and often takes years to accomplish. After sufficient width and depth -have been undercut, the capping starts to break away, but through arching large masses of rock-.fill the opening, support the capping, and retard the continuation of caving. Caving to the surface is, therefore, retarded until either a sufficient thickness of the orebody is removed, or the width and length of the undercut part have been greatly increased. I wish to emphasize this fact of slow caving, for it is on, this principle that the success of the Athens system. largely depends.

Jan 8, 1920

By E. L. Estabrook, H. H. Hill

This report summarizes the information that was obtained by the Committee on Unit Operation in Eastern United States and in the foreign countries. Letters and questionnaires were sent to all of the Eastern members of the Petroleum Division of the American Institute of Mining and Metallurgical Engineers and to those who are living outside of the United States, asking them to advise the Committee of any unit operations that are in effect in the various countries of the world and to furnish the names of men to whom inquiries should be directed for detailed information on the different projects. The response to the Committee's request is worthy of note. Practically all of the members who had knowledge of foreign operations replied to the questionnaire and not only furnished information that was of value to the Committee, but they evidenced a real interest in the subject of unit operations and assured the Committee of their willingness to assist in every way possible in order to make the study a success. The Committee wishes, at this time, to express its appreciation of the excellent cooperation that was received from the members of the A. I. M. E. to whom questionnaires were sent. Unfortunately, the limited time that has been given to this survey did not permit the collection of detailed data on the different unit operations that are now in effect. It required several weeks to get back replies from the members located in some of the foreign countries and as a result the men who were asked to furnish information on the various projects have not had sufficient time to submit the detailed data that were requested. The Committee has been assured, however, that information relating to a number of unit operations will be furnished in the near future. Part of the delay has been due to the fact that the purpose of the study was not understood and because the terms "unit" and "near-unit" operations were not clearly defined. In the foreign countries, practically all of the operations in noncompetitive fields are on concessions or leases that have been granted to a single company and for that reason

Jan 1, 1930

By Everett Carpenter

THE average daily production of crude oil-in Kansas a1 the beginning of the year was about 71,000 1 bbl. and, at its close, 82,000 bbl.-an increase of 11,000 bbl. per day. The total production for the state during the year was about 28,250,000 bbl., or an average of practically 77,500 bbl. per day for the year. This increase in the production was the result of the discovery of several new pools of high-grade oil. COWLEY AND SUMNER COUNTIES One of the principal factors in bringing the production of the. state back to its former level was the newly discovered pools in western Cowley County. During December, 1923, the Waite Phillips Co. completed its Johnson No. 1 in Sec. 20, T. 33 S., R. 3 E., which opened up the Rainbow pool about 12 miles southwest of Winfield. In this pool, the production comes from the Burbank sand, locally called the "Rainbow," found at a depth of 3200 ft. The sand varies in thickness from 25 to 40 ft. in the seventeen wells completed during the year, and the initial productions ranged from 300 to 3000 bbl. per day of 40° Be. oil. The Rainbow pool is purely a wildcat discovery, for no. rocks suitable for the use of the geologist are present. To determine the geologic conditions, the larger companies core-drilled the Rainbow area immediately after the discovery. The Marland Refining, Co., drilling on the Graham farm in Sec. 9, T. 33, R. 3, failed to find the Burbank sand and continued to the Siliceous lime, often erroneously called the Wilcox, at 3505 ft., where a well with an initial production of 900 bbl. of 40 Be. oil was obtained. In the development following this discovery, 4 additional wells were completed, 3 of which encountered pay sand at 2500 ft., the initial productions each being about 200 barrels. Judging by the sands already proved and the area indicated as probably oil bearing by the development to date, these pools have a very promising outlook for the future. It is not unlikely that a field second only to El Dorado may have been opened.

Jan 3, 1925