Search Documents

By Howard Eavenson

THE eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) is width, the hill sides slope from 25° to 33°, and the tops, from 600, to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate, the use of a large number of local pumps or of numerous drainage ditches to keep the mine free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In hew workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and. unless from three to four times as many pumps are installed as are normally needed, considerable', output is lost. In most cases the water will .flow from the mines, so the obvious solution is to provide drainage .ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places.

Jan 1, 1921

By Michael Heximer, Dominic Verfielst, Timothy Moore

"Teck's Trail Operations recently installed new pressure filters in the cold stage purification step in the zinc leaching plant. Alloy 2205 duplex stainless steel was chosen as the material of construction as it was in use in the hot stage purification operation. Within a year of commissioning, an unacceptably high rate (greater than 1 mm/y) of corrosion was observed on the weld heat affected zone (HAZ). Laboratory and field tests were conducted to establish the conditions under which the corrosion was occurring. The tests isolated the aggressive conditions to a unique combination of materials present during the filter regeneration stage. Furthermore, the change of the duplex grain structure of the alloy during welding resulted in the HAZ being more susceptible to the corrosive environment. A new material of construction was recommended as a result of the investigation.IntroductionThe sulphide leaching plant uses four horizontal tank pressure leaf filters to remove solids precipitated in the cold stage electrolyte purification process. The current filters were installed in 2007, and replaced a bank of filter presses. The material of construction for the filters - alloy 2205 duplex stainless steel - was selected based on its successful use in similar service areas of the leaching plant. However, within the first year, unexpected and rapid corrosion of the filter tank material was observed. Although moderate general corrosion was noted throughout the filters, the attack was particularly aggressive in the areas where intense heat was applied during fabrication, observed at the HAZs caused by welding, and on the exposed edge grain of the duplex plates. On the inaugural annual inspection of the filters in the first year of operation, a corrosion penetration rate of 1.0 to 1.5 mm/y was observed at the HAZs. The parent plate of the pressure tank was a minimum of 6 mm, with a minimum allowable thickness of 3 mm under the ASME pressure tank design rules. Therefore, the projected useful life of the filters could then be roughly calculated to be two to three years. Urgent action was required to understand and correct this problem."

Jan 1, 2012

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

By K. V. Lindell

THE 70-mile serpentine belt of eastern Quebec, producing 70 pct of the world's chrysotile, has 11 operating mines, two of which are underground, eight are open-pit, and one is both open-pit and underground. The combined operation, the Jeffrey mine, of the Canadian Johns-Manville Co., Ltd. is the largest producer in the group. Haulage All four of the separate operations falling under transportation at the Johns-Manville Jeffery Mine at Asbestos, P. Q., is handled by the company owned Asbestos and Danville Railway. A variety of equipment is operated over the 25 miles standard gage railway. Included in the scope of transportation are: 1-Hauling mill rock to the mill. 2-Hauling stripping and waste rock to the waste dump. 3-Hauling mill tailings to the tailings dump. 4-Hauling supplies from, and finished products to Danville. Main line tracks are permanent, but those within the pit and on the dumps have to be relocated constantly to follow the mining face and dump edges. Tracks within rock areas in the mine are laid on steel ties and can be moved by a bulldozer. Standard mechanical track shifters move tracks in dirt areas in the mine and on the dumps. Train-movements, both within the mine and over the out-lying tracks are controlled by a dispatcher located at the southwest rim of the pit. Steam locomotives haul all stripping, waste rock, and ore from the mine to the gathering yard at the northwest rim of the pit. Normally, two trains per operating shovel are used, with adjustment for optimum loading. In the event of shovel loading on the bottom level or in good stripping, service may be increased to three or four trains per shovel. From the gathering yard a 100 ton diesel-electric locomotive hauls the mill rock to the mill slips, a distance of about three miles. Electric or steam locomotives haul the waste rock and stripping to the waste dump located about two and one-half miles from the mine. Stripping cars are sprayed with a chloride solution and "gravelled" to prevent wet stripping from freezing in the cars during the cold months. Cars pass under a shaking screen which distributes an even

Jan 1, 1952

By B. M. Bird

ONE of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practise for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical danc-ing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1928

By E. W. Krampert

Oil development continued active in Wyoming during 1937, with much of the interest centered on prospecting for new pools, following a rather intensive seismograph play in 1936. The new fields of Lance Creek, Medicine Bow and Quealy were the centers of intense development in proved areas, but routine drilling occurred in most old fields. A new and deeper producing horizon (the Leo sand) was opened up in the Lance Creek field, which materially extends the producing area and will probably account for continued active development during 1938. The discovery in 1936 of oil in the Eocene Wasatch formation at Powder Wash, northwestern Colorado, tended for a time to stimulate prospecting in the deep Tertiary basins, but this interest as rapidly declined after drilling several failures on similar structures and the discovery that the productive area at Powder Wash itself was very small. A most interesting test of an Eocene structure was drilled by The Superior Oil Company of California on the South Baggs structure, in Carbon County, Wyoming. South Baggs is one of the best developed structures in the Red Desert Washakie Basin, which also includes the Hiawatha gas field and the Powder Wash gas and oil field. The Superior Oil Co. started the well according to contract but apparently had lost interest in the prospects, for it abandoned the well at 2138 ft. without testing the oil-bearing and gas-bearing horizons of the Wasatch. The Sinclair Wyoming Oil Co. drilled a deep test in the Muskrat gas field to the Madison. This well discovered oil in the Embar formation, which was considered noncommercial because of depth. After the Embar was abandoned the hole was plugged back and the various sands tested by shooting through the casing with the Lane-Wells gun. The Lakota sand was found to contain high-pressure gas and the well was completed as a 24-million-foot gasser at 2175 lb. rock pressure. This is a new sand in an old field. The Italo Petroleum Co. drilled a flank well on the Hamilton dome structure and found oil in the lower Embar formation. Thk merely extends the limits of production, as one old well on the structure had

Jan 1, 1938

By C. W. MacGregor

IN the testing of materials there exist various methods of recording graphically the behavior of a material subjected to tensile stress. Prob-ably the most common method is to plot the tensile stress So, obtained by dividing the load P by the original area of cross section AO at the start of the test, as a function of the strain ?o, which is obtained by dividing the ?Lo or the change in the gauge length by the original gauge length Lo. A list of the symbols used here is given in Table 1. This method, while it has proved useful in the routine testing and comparison of various materials, does not have a very sound physical basis, as was first pointed out by P. Ludwik1, and consequently does not afford a very deep insight into the true physical behavior of the material under stress. Among the objections to this method may be mentioned: (1) that by dividing the load P at any stage of the test by the original area Ao a fictitious stress is obtained, which does not actually exist; (2) that the strain ?o = ?Lo /Lo is not an exact expression for the true strain for large values of ?Lo in per cent of Lo; (3) that when necking starts the strain varies considerably along the gauge length and the above expression no longer gives the true strain existing at any point on the outside of the bar; and (4) that the axial strain varies over the cross section of the necked portion and ?o does not represent an average of these strains over the cross section. Stresses taken from such a diagram would be only approximate and, if used to compare results of a test on a given material under simple tension with results obtained under combined stresses, certain errors would he thus introduced. In order to overcome some of these objections, various methods have been suggested, both as to the quantities to be measured and as to their graphical representation. In some cases the so-called "true stress," obtained by dividing the load P by the actual area of cross section A existing when the load P was applied, is plotted as a function of the strain

Jan 1, 1937

By H. Y. Yancey, B. M. Bird

One of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practice for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical dancing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1930

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By Henry D. Hibbard, Edward L. Ford

The process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon, which could be done on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls. Since Holley's paper, important improvements have been made from time to time in both plants and methods for washing iron, and the

Jan 1, 1916

By Paul D. Merica, L. J. Gurevich

In connection with other investigations on the properties and characteristics of chilled-iron car wheels, the question as to the best range of annealing temperatures was raised. Chilled-iron wheels are cast with a chill against the tread and the inside of the flange, the remainder being in sand. The composition of the metal is so chosen that under these conditions the trcad and inside of the flange will show white iron to a depth of from 5/8 to in. (15 to 22 mm.), the remainder of the wheel becoming graph itized or gray. In order to relieve the stresses set up during cooling under such drastic conditions, the wheels are stripped from the mold, while still red hot, piled in a soaking pit, and allowed to cool very slowly from their temperature at stripping. Obviously the most suitable temperature for this annealing is the highest at which no formation of graphite occurs within the white tread and at which the wheels can be stripped from the molds. Inasmuch as no direct determinations have been made of the temperatures at which the formation of graphite takes place in white iron of compositions used in car wheels upon annealing, it was considered worth while to determine these temperatures as a means of establishing the maximum temperatures at which the annealing of the wheels may be carried out. In the course of this work, some incidental observations were made which are of interest in connection with the theory of graphitization in whitc iron. The literature on the subject of the formation of graphite both during cooling at casting and upon annealing is very extensive and can be best studied by reference to a comprehensive discussion of the subject by Hatfie1d.l Perhaps the most important contributions of previous investigation are the following: 1. Whether a given mass of molten iron becomes white, mottled, or gay upon casting, depends on its composition and its rate of cooling through the temperature range of solidification and immediately below. 2. The more rapid the rate of cooling, the less is the extent of graphitization.

Jan 1, 1920

By C. W. MacGregor

In the testing of materials there exist various methods of recording graphically the behavior of a material subjected to tensile stress. Probably the most common method is to plot the tensile stress So, obtained by dividing the load P by the original area of cross section A0 at the start of the test, as a function of the strain e0, which is obtained by dividing the ?Lo or the change in the gauge length by the original gauge length Lo. A list of the symbols used here is given in Table 1. This method, while it has proved useful in the routine testing and comparison of various materials, does not have a very sound physical basis, as was first pointed out by P. Ludwikl, and consequently does not afford a very deep insight into the true physical behavior of the material under stress. Among the objections to this method may be mentioned: (1) that by dividing the load P at any stage of the test by the original area A. a fictitious stress is obtained, which does not actually exist; (2) that the strain e0 = ?L0 is not an exact expression for the true strain for large values of ?LO in per cent of Lo; (3) that when necking starts the strain varies considerably along the gauge length and the above expression no longer gives the true strain existing at any point on the outside of the bar; and (4) that the axial strain varies over the cross section of the necked portion and e0 does not represent an average of these strains over the cross section. Stresses taken from such a diagram would be only approximate and, if used to compare results of a test on a given material under simple tension with results obtained under combined stresses, certain errors would be thus introduced. In order to overcome some of these objections, various methods have been suggested, both as to the quantities to be measured and as to their graphical representation. In some cases the so-called "true stress," obtained by dividing the load P by the actual area of cross section A existing when the load P was applied, is plotted as a function of the strain

Jan 1, 1937

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle coal at the rate of 200 tons a day. By 1860, revolving screens were in wide use in the Pennsylvania anthracite field. Shaking screens were introduced in the Pennsylvania anthracite region in the 90&apos;s and they rapidly displaced the lower-capacity revolving screens.

Jan 1, 1950

Some 15 years ago, Dr. Adolf Schmidt, director of the Magnetic Observatory in Potsdam, Germany, developed an instrument, which was a modification of Lloyds balance, for the measurement of the vertical component of the earth&apos;s magnetism in the field. There was a keen demand for this because (1) it was desirable to have a field instrument that would measure the component of the earth&apos;s magnetism which stands in the closest and simplest relation to the configuration of the subterranean magnetic formations-the vertical component; (2) it was desirable to have an instrument that was not only more sensitive but also more reliable than the existing vertical magnetometers (the dip needle, for instance). The application of the magnetometer in oil geology demanded such an instrument, because the magnetic disturbances produced by most types of magnetic formations associated with the occurrence of oil (salt domes, faults, anticlines with crystalline core, etc.) are too small to be detected with the ordinary dip needle. The writer can prove, by some investigations recently made for the U. S. Bureau of Mines, that these instruments may be used also to very great advantage in mining, because they are capable of measuring anomalies which are as great as twice the normal strength of the earth&apos;s magnetic field. Even for such anomalies, the field balance is more advantageous than the dip needle. First, the instrument rests on a firm support and can be adjusted in the proper azimuth, which insures measurement of the vertical intensity only, without a part of the horizontal intensity, which is very important for the interpretation. The readings give the vertical intensity in linear terms and not as a function of an angle; and the field balance is insensitive to temperature when used with scale values that are adequate for the determination of large anomalies. In another phase of mining, the gold placer work, the field balance has also shown excellent results for which the dip needle is not adequate. What has been said about the dip needle holds also, though to a lesser extent, for two other types of vertical variometers recently used, the Tiberg balance and the Thomson-Thalen magnetometer.

Jan 1, 1929

By Stephen Taber

A vein may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-bearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-books today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped masses should be classed as veins or as dikes. Some of the earlier investigators have also advocated the theory that veins are contemporaneous in origin with the inclosing rock, while others have believed the vein minerals to represent a recrystallization or transforma-

Jan 1, 1920

HE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe2O3), and phosphorus oxide (P2O5) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1951

THE slag performs two useful functions. in open-hearth steel-making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SO2, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (SiO2 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1951