Search Documents

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By George W. Crawford, W. P. Aycock, E. W. Hough

Forty oilfield brines have been examined so far by a polarographic technique new in petroleum engineering called the "tensatnmetric method" by the team of biochemists who perfected its use in their field. Samples of brine were obtained from various oil fields in which the wells were known to be producing fluid from oil productive zones in well-known geologic formations. Most of the reservoirs from which the samples were obtained are believed to have an active water drive under the prevailing conditions of operation. The 40 samples represent brines produced front 16 different formations of various geologic ages. Graphs have been prepared of the data obtained in the testing of each sample, and the distinctive waife-like curves so obtained are characterized by reproducible profiles, called "response curves." Careful comparison of the response curves of salt water coming from different fields producing from the same geologic formation reveals that the curves are similar. The response curves of salt water coming from productive zones of different geologic formations are characteristically different. Preliminary work offers the further hope that response curves of an oilfield brine indigenous to a particular oil-bearing formation and hence representative of a particular geologic environment, such as deposit-ional and all subsequent morphological conditions, may be of value in reservoir engineering in the interpretation of surface and interfacial phenomena. For example, the wettability of the rock matrix and more specifically, the classification of productive oil-bearing strata as hydrophyllic or hydrophobic may be determinable. However, many more brines must be examined and the resulting response curves analyzed in comparison to known causal phenornena before this objective is achieved. INTRODUCTION One of the perennial moot questions in the literature of petroleum engineering is whether the reservoir rock is oil- or water-wet. Possibly an answer to this question could come from a careful examination of oilfield brines. None of the conventional methods of examining brines (chemical analysis, pH and electrical conductivity measurements, and the like) answer the question. Careful analysis of reservoir behavior observed in the exploitation of oil fields, particularly in the application of fluid injection, has been fruitful to the extent that a few reservoirs are believed to be properly classified. Physical chemistry suggests the behavior of reservoir brine and rock may be due to something in the brine in small amount. The ever increasing development and modification of theory in the general field of surface and interfacial chemistry has, and is, contributing to a better understanding of the problem, particularly as theory is verified by data. The work herein reported was begun in 1953 by Hough and Roebuck 1,2 who employed a new form of alternating current polarography, i.e., tensammetry, developed by Breyer, et a13,4 and who studied eight oilfield brines in adapting tensammetry to petroleum engineering needs. THEORY AND DEFINITIONS Tensammetry is a new technique of inquiry into surface phenomena. Specifically, a weak alternating current voltage is superimposed upon the direct current voltage applied to a dropping mercury electrode in contact with an electrolyte containing a small amount of a surfactant. The resultant alternating current can be measured and provides the experimental data for this new area of research. Under the influence of the direct current voltage, polar molecules arrange themselves in a double layer at the electrode. This double layer may be compared to a variable condenser, the capacitance of which is a function of the imposed direct current voltage. The direct current voltage determines the degree of adsorption of the surface active molecule on the electrode. Whenever the molecules are strongly adsorbed on the electrode, the capacitance of the double layer is low and the alternating current through the cell is low. Desorption occurs at some values of the direct current voltage, and at these voltages the capacitance of the double layer is high, resulting in an increase in the alternating current through the cell. The direct current

Jan 1, 1958

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

The authors of T.P. 4179 have conducted a large number of experimental water floods, and the data are reported in a very clear manner. These data show significant variations of residual oil saturation with changes in wettability, interfacial tension, flooding rate, and oil-water viscosity ratio. Furthermore, some of the data obtained cover a range of variables not previously reported in the literature. It is our opinion that at least some of the observed variation in oil recovery can be obtained only in floods made under conditions identical with those used by the authors. There are other systems which may be said to have the same wettability, but which exhibit an entirely different qualitative dependence of oil recovery on the experimental variables. In this regard, we would like to direct attention to several items which we feel are not given sufficient consideration in the paper. The first of these items has to do with wetting equilibrium. A survey of the current literature will reveal that little is known, and even less is understood, about wetting equilibrium. This is particularly true of the relation between contact angle measurements made under static conditions, and the wettability existing under the dynamic conditions of floods carried out at relatively high rates. We feel that this is a very important consideration, particularly in the floods the authors performed under what they consider to be "water-wet" conditions. It is our opinion that wetting equilibrium did not exist in these floods, except possibly at the very lowest rates. This opinion is in part based on some flooding tests we have made which are very similar to some of those described by the authors. These floods were made in unconsolidated cores, 6 in. long and 13/4 in. in diameter, made up of carefully graded glass spheres of the approximate size of the sand grains used in the subject paper. The cores were mounted vertically, and distilled water was used to displace a refined oil equivalent to the authors Soltrol C. The glass spheres had previously been carefully cleaned so that they were strongly wet by the water. The floods were made with and without an interstitial water saturation. When interstitial water was present, the solid surfaces were mostly covered with water prior to injecting the flooding phase. Consequently, a condition very near wetting equilibrium existed throughout the flood. The data in Fig. A show that under these eircumstances, rate had no influence on residual oil at flood-out, over the range of rates studied. On the other hand, in the absence of interstitial water, the surfaces are all covered with oil before the displacement. To achieve wetting equilibrium the injected water must displace the oil from the surfaces themselves. This is not a fast process. Therefore, the effective dynamic wetting condition in floods of this type must depend upon the flooding rate. When the flood rate is very low, compared to the rate at which wetting equilibrium is attained, the residual oil saturation at flood-out is essentially the same as the residual obtained when interstitial water is present. This is shown in Fig. A, and occurs because the dynamic wetting conditions are the same in both cases. However, at moderately high flooding rates, the rate has an important bearing on the amount of oil recovered because in this case the attainment of surface equilibrium is the slow step. We believe that, in the absence of an interstitial water saturation, oil recovery varies with rate because of the reasonably slow approach to wetting equilibrium which occurs during the displacement. In fact, as the rate is increased, the oil recovery performance indicates the core is becoming progressively less water-wet. At the highest rate there is even considerable simultaneous production of oil and water after breakthrough. This does not occur at the lower flooding rates, nor is there appreciable simultaneous oil and water produc-

Jan 1, 1957

By C. B. Alcock, R. G. Hudson

Sulfur pressure measurements above FeS in equilibrium with iron have been carried out by the Knudsen orifice method. A comparison is made of the weight loss of the cell per unit time obtained in the above experiments, that calculated from Richardson and Alcock's measurements of the S2 pressure above FeS in equilibrium with iron, and the dissociation constant for diatomic sulfur from spectroscopic and thermal data. EXTENSIVE equilibrium measurements have been made to determine the sulfur potentials of a great many systems of metallurgical interest.' In order to confirm their reliability, to supply data which may be of use in further thermodynamic calculations, and to establish the reliability of the Knudsen orifice in obtaining accurate thermodynamic values at high temperatures, the present investigation on the pressure of the gaseous species above FeS in equilibrium with iron has been carried out. The Knudsen orifice method has been used for these pressure measurements. Experimental The apparatus and general technique for this investigation are the same as that reported for the determination of the vapor pressure of silver.' To reduce the residual gas pressure in the evacuated chamber, a titanium getter, maintained at run temperature, was introducbed. Several types of Knudsen cells were used—platinum, zircon, and fused silica. The orifice in the zircon cell was fashioned with a small diamond wheel. The same precautions were used in this investigation as were employed in the work on Mo2S2.3 The FeS-Fe mixture was prepared by heating a sample of pure FeS,, supplied by K. K. Kelley of the Bureau of Mines, with excess iron powder, cp grade, obtained from the Fisher Scientific Co. These two substances were heated in a closed Armco iron crucible at 960°C, held in a vacuum of less than 10" mm Hg for 24 hr. The mass was then removed from the cell and ground in an agate mortar. In this form it was charged to the various Knudsen cells. Heating the Knudsen cell for an additional two days was sufficient to obtain constant rates of weight loss of the cell. The data obtained in this investigation are recorded in Table I. To establish whether or not a sulfide of iron is volatile at these temperatures, 0.7646 g of the FeS-Fe mixture, described above and containing 69.2 pet Fe, was placed in the zircon Knudsen cell. Run Nos. 103 to 109 were performed on it. After the completion of these runs, the total amount of iron left in the cell was obtained by chemical analysis. It contained 0.537 g Fe, compared to 0.529 g in the original charge. Thus, there was an apparent gain in iron of 1.5 pet. This is attributed to unknown experimental error, and the conclusion is that no sulfide of iron is volatile. The vapor pressure of pure iron4 is about one thousandth that of the sulfur pressure' at these temperatures. The vapor pressure of iron inside the Knudsen cell will be almost exactly that of pure iron, since in the iron-rich phase the percentage of sulfur is of the order of 0.025 pet.At this low percentage of sulfur Henry's law is probably obeyed by the sulfur. Thus, the iron will obey Raoult's law. In any event, the vapor pressure of iron will be lower than that of pure iron and, since the vapor pressure of pure iron is negligible compared to the pressure of sulfur, the weight loss of the cell due to the vaporization of iron should be negligible. Since neither iron nor FeS is volatile to an appreciable extent, the total weight loss of the cell must be due to the vaporization of sulfur. Discussion and Calculations On the assumption that S, is the only gaseous species present in appreciable quantity, its pressure

Jan 1, 1957

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By B. H. Bergstrom, J. J. Gilvarry

Previously the authors showed that the Gilvarry equation correctly describes the distribution of fragment size in single fracture, provided the exoclastic particles showing original surface of the specimen are removed from the distribution. In the present work this conclusion has been strengthened in two respects. First, it has been shown that the existence of two peaks in the differential distribution for the endoclastic particles, corresponding to the effect of surface and volume flaws in the interior of the specimen, can be demonstrated from the average of data for a large number of specimens. Second, it has been shown by means of a Coulter counter that data obtained from specimens fractured in gelatin display the behavior at fragment sizes approaching 1 p which is demanded by the limiting form of the Gilvarry equation in this case. In previous work, a rigorous derivation of the proper distribution function for fragment size in single fracture of a brittle solid has been given by Gilvarry,' based on a closely defined physical model and deduced strictly by the laws of probability. Experimental work has been reported by Gilvarry and Berg-str~m,~ confirming the theory in its broad outlines. Subsequently, Gilvarry and Bergstrom extended the theoretical discussion to include comminution and presented experimental data bearing on this point. They have described further experimental results for the case of single fracture recently. The experimental evidence regarding single fracture was rather convincing. However, it was based on only five specimens for which fragment sizes were determined by sieve analyses and three for which measurements in the finer sizes were made on a Coulter counter. The purpose of the present paper is to extend the experimental results as obtained by means of both sieve analyses and the Coulter technique. In the former case, sufficient specimens are included so that the average data should vield ac- curately the detailed behavior of the distribution function for the coarser fragment sizes. In the latter case, measurements for the finer sizes are reported which correspond to single fracture more closely than prior results and fill a lacuna left in the experimental verification. In addition, an extension of the theory given recently bGilvarry for the case of fracture of a two-dimensional solid will be outlined, and experimental results obtained by him will be discussed.6 THREE-DIMENSIONAL CASE Gilvarry' has shown that the Schuhmann size modulus is a measure, in a sense specified later, of the number of activated edge flaws in a specimen undergoing single fracture. Single fracture is defined as that resulting from a single instantaneous application of energy, such as the blow of a hammer whose motion is halted when fracture begins. Plural fracture consists of a short sequence of single fractures, as in a jaw or gyratory crusher; multiple fracture obtains when many applications of energy are made, as in a ball mill. The Griffith flaws associated with fracture of a specimen are flaws occurring within the volume of the body, on the new surfaces created within its interior and on the new edges (intersections of two surfaces) within the body. Fracture proceeds by activation of flaws in the volume of the specimen, in the fracture surfaces throughout its interior, and in the edges produced by intersection of fracture surfaces. If all the flaws and all groups of flaws are distributed at random, independently of other flaws or groups thereof, it has been shown by Gilvarry that the distribution function for fragment size has the form of a Poisson distribution. The fraction y, by weight or volume, passing a sieve of mesh size x is given by where k is an average spacing of activated edge flaws, j2 is an average amount of surface containing one activated surface flaw and i3 is an average volume corresponding to an activated volume flaw. The averages in question are referred to the mean dimension x of a fragment. On the basis of the theoretical

Jan 1, 1962

By K. H. Ribe

Water often enters an oil reservoir during completion or workover operations on a well and forms a partial "water block" to oil production. A mathematical study of radial two-phase flow, neglecting capillary effects, has been employed to study the formation of such a water block and subsequent re-moval by production from the well. The effects of reduced oil permeability about the well on the well productivity were studied. The fluid saturation distributions about the well during formation and removal of the water block have also been computed. Several relative permeability relations and viscosity ratios were employed. If water has invaded the formation, its influence through relative permeability effects alone can cause the following. 1. Oil productivity will be depressed for extended periods after production is resumed and will build up only gradually as the water is removed. 2. Oil injected for treatment of water blocking will delay rather than promote restoration of full well productivity by enlarging the region invaded by water. Thus, unless the specific action of chemicals contained in the oil is needed, oil injection appears undesirable. INTRODUCTION During oilwell workover operations, water may enter the oil-bearing formation from the wellbore. When production is resumed, oil must flow through the region invaded by this water. The presence of this region can cause both well productivity and oil production rate to be low and oil to be produced with high water-oil ratio for some time after production is initiated. This situation is sometimes described as a water block. The introduction of water into the formation may result in other actions which also lead to reduction in well productivity and which are also usually included in the connotation of the broad term, water block. Often considered, for example, are the possibilities of clay swelling by contact with fresh water and the formation of emulsions with the formation oil. If it is suspected that such specific actions have taken place, remedial treatments are undertaken which usually involve the injection of chemicals in oil. Since the introduction of water, even in the absence of specific interactions with the formation or oil, will cause a temporary water block (which might be misinterpreted as evidence of a more severe situation), it is of importance to evaluate the magnitude and duration of this blocking which results purely from the reduction in relative permeability to oil in the vicinity of the wellbore. It is also of interest to evaluate the effect of oil injection on the productivity of a well blocked by water in this manner. Inasmuch as this unfavorable condition may persist for some time, it may lead to premature condemnation of a workover or premature abandonment of a potentially productive pay zone. A quantitative evaluation of the influence of water entry on the oil productivity through changes in relative permeability was made by solving a radial form of the Buckley-Leverett equation. The distribution of water saturation around the wellbore during the entry of water was calculated and was followed by a similar calculation of the saturation distribution during the period of resuming production. At any stage in the removal of the invading water, knowledge of the distribution of its saturation permitted calculating the attendant loss in oil productivity. The influence of the shape of the relative permeability relationships was also evaluated by carrying out the calculations for two hypothetical cases. Further, the effect of the oil-water viscosity ratio was examined by repeating the calculations, for several ratios of unity and greater, with the same relative permeabilities. Fi-nally, results are presented to show how the length of time a well must be swabbed to resume production depends on the length of time it has been subjected to invasion by water. STATEMENT OF THEORY Differential Equations Water is assumed to enter a producing formation which is initially at the connate-water saturation and contains no gas. The water and oil are treated as in-

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

By Attilio Ligasacchi

The production of magnetite in copper smelting has been the subject of wide investigation in the past.1-9 It is accepted that most of the magnetite is produced in the converters and returned to the re-verberatory furnace with the converter slag. Part of this magnetite is circulated back to the converters in the matte. As a result, if proper fluxing practice is not followed, and temperatures in the converting process are not strictly controlled, an undesirable circulating load of magnetite may occur. This might ultimately lead to saturation in the reverberatory bath with consequent settling of the magnetite at the furnace bottom. This paper contains the cumulative results of a series of investigations on the formation and control of magnetite presently being conducted by the metallurgical department of the Chino Mines Division of Kennecott Copper Corp. THE METHOD USED FOR THE DETERMINATION OF MAGNETITE AND OTHER MAGNETIC MATERIALS Conventional wet chemical magnetite analyses are neither reproducible nor theoretically sound. These analyses are sensitive to time, temperature, and heating rate-all factors which tend to decrease their accuracy and reproducibility. To overcome the unreliability of the above method, H. W. Mossman1 developed an inductance bridge magnetite "meter" which completely replaces the wet chemical analysis with the advantage of quicker and reproducible results. Fig. 1 is a schematic diagram of the meter in use in the Chino metallurgical laboratory. When a pulverized specimen with magnetic properties is placed in coil A of the inductance bridge circuit, the permeability of the core is increased, causing a voltage drop across the coil. The unbalance is amplified to operate the balancing motor which adjusts the movable iron core in coils C and D to bring the bridge back to balance. An indicator arm connected to the movable iron core indicates directly the percent, or weight, of the magnetic material in the specimen. Coil B acts as a reference coil and a zero adjustment. The meter is standardized with a set of various amounts of -100 mesh pure magnetite crystals (99.8 pet Fe3O4) thoroughly mixed in a test tube with -100 mesh quartz sand. These mixtures are combined with inert transoptic powder and heated to 140° to 160°C (melting point of the powder) and subsequently cooled to room temperature, solidifying the whole mixture, in this manner eliminating any possible preferential orientation of the magnetite grains. In order to determine the effect of the particle size" of the magnetite and other magnetic materials on the meter determinations, five size fractions were obtained by wet screening of the 99.8 pet pure magnetite and several reverberatory matte and slag samples. The following size fractions were investigated: -80 + 100; -100 + 150; -150 + 180; -200 + 250; -250 + 300 and -100 mesh. The deviation of the meter readings for the various sizes of each sample never exceeded ±0.3 pet. This deviation is considered well within the accuracy needed for common smelter operation procedures. Further investigation proved also that grinding slag and matte samples in our laboratory disc grinder normally produced a powder constituted of 95 pet -200 + 300 mesh. For practical purposes a - 100 mesh size was used as standard for our studies. It was also found that for rapid determinations tamping of the sample in the test tube was sufficient and gave comparable results with those samples solidified with transoptic powder. For the purpose of this study we define the magnetite content in copper smelter slags and matte as the equilibrium amount of crystalline Fe3O4 existent in the specimen at a given reference temperature, excluding any secondary magnetite precipitated in the specimen during nonequilibrium conditions. MAGNETITE DETERMINATION IN SLAGS Since it is impossible to ascertain the status of equilibrium of a conventional slag sample, due to

Jan 1, 1965

By J. F. Smith, J. R. Ogren, N. J. Magnani

The uapor pressrcres of magnesium over binary alloys of magnesium with twelve of the yare-earth eletnetzts have been measured by the Knudsen effuion method in the temperature range 675° to 910°K. These vapor-pressure measurments were combined with data concerning the tevtrlitzul magnesium solubility and the vapor pressure of pure magnesinm to evaluale the standuvd free energies of pluase jormation. These free-etzergy values indicate that the CsCl structures of the heacy rave earths tend to be somewhat less stable than those of the light rare earths. This dif-]eying- behaviov covrelates with differences which have been obsevz~ed in other alloy systetns wherein a phuse appeurs, disappeavs, or changes crystal stvucture as the atomic number of the rare-earth com-ponent is changed. This behauior also appears to correlate with the struclurul rariations within the rare-earth elements themselves, and it is speculated that cariations in the spatial extent of the 4f orbitals are responsihle. STUDIES of the phase relationships and crystal structures in the binary systems between rare-earth metals (lanthanons) and magnesium are extensive but far from complete. However, the currently available information1-10 does produce a rather interesting pattern. This is illustrated in Table I. If one excludes europium and ytterbium from consideration because of their generally atypical behavior, it can be seen from the table that the phase relationships in the magnesium-rich regions show a distinctly different pattern for the lighter lanthanons as compared to the heavier lanthanons. For the lighter lanthanons, LnMg2 phases occur from lanthanum to gadolinium with the cubic MgCu2 structure, LnMg3 phases occur from lanthanum to terbium with the BiLi3 structure, and magnesium-rich phases occur from lanthanum to gadolinium with stoi-chiometries between Ln5Mg42 and LnMg12. In contrast, for the heavier lanthanons, those LnMg2 structures which have been examined have the hexagonal MgZn2 structure, LnMg3 phases have not been observed beyond terbium, and the magnesium-rich phases occur with the a manganese structure near a stoichiometry of Ln5MgZ4. The heavy lanthanon-magnesium systems thus appear to be analogous to the Y-Mg system""2 wherein YMg has the CsCl structure, YMg2 has the MgZn2 structure, and the region Y4Mgz5-Y5Mg24 has the a manganese structure, and no other intermediate phases are observed. Similarity in alloying behavior between yttrium and the heavy lanthanons occurs commonly, and on this basis it seems likely that LnMg2 phases will be found with the MgZn2 structure in the binary systems of dysprosium, thulium, and lutetium with magnesium when the appropriate investigations are made. In the case of the magnesium-rich phases of the lighter lanthanons, only the Ce-Mg phase relationships have been investigated thoroughly and in detail, and until similar investigations are made for the other systems there will remain questions as to which magnesium-rich stoichiometries represent equilibrium phases and what systematic variations occur in the sequence from lanthanum to gadolinium. Thus the data in Table I show that only the LnMg phases occur with the same crystallographic structure throughout the sequence from lanthanum to lutetium. It was speculated that the relative stability of these LnMg phases might vary from one lanthanon to the next in such a way as to presage the differences which occur among the more magnesium-rich lanthanon-magnesium phases. On this basis the present investigation of the thermodynamics of phase formation was Gndertaken for the LnMg phases. PROCEDURE AND RESULTS A generalized phase diagram for the lanthanon-rich portion of a lanthanon-magnesium alloy system is shown in Fig. 1 where ß represents a high-temperature bcc

Jan 1, 1968

By E Cunha, D Roldao, TáTamantini, J F. C L Costa, T Webber, C Monteiro

The main problem of geostatistical simulations is to reproduce the real characteristics of the mineral deposit when there are few conditioning data. In this case, the geological interpretation, based on structures, geophysics and geological maps, plays the major role in terms of resource evaluation.The paper investigates the use of principal component analysis (PCA) to help classify multiple geostatistical categorical simulations considering the similarity among them and the interpreted model, herein referred as training image (TI).An iron deposit with four lithological facies, in a specific horizontal plane, was used as case study for two-dimensional (2D) simulations. Sequential indicator simulations (SIS) was used to obtain ten equally probable 2D images, which were generated and compared against the interpreted model (TI).In this study, 11 random variables are comprised by the vector of ten SIS realisations plus the training image (TI). The similarity between the TI and each SIS realisation is measured using the angle between the TI and SIS vectors projected in the new coordinate systems (PCA factors). It is possible to order the SIS realisations from the highest to the lowest PCA factor taking into account the TI similarity.The visual analysis of the images shows coherence in the PCA results as a method to measure similarity. This methodology can be used as a post-processing tool to rank simulation results and to select the ones which better represent the prior known geology or to compare the quality of different methods of simulation.

Sep 26, 2011

By T. N. McVay

The Bureau of Mines has developed a field test for detecting the presence of columbium in a variety of minerals containing the clement. The test consists of fusing the mineral or rock powder with potassium pyrosulfate in a porcelain crucible, digesting the melt with hot dilute hydrochloric acid to release the columbium oxide (Cb205), and subsequently reducing the columbium oxide to a lower oxide by adding tin, which gives a blue color to the contents of the crucible. The method will detect 1 percent of contained columbium oxide (Cb205) in a mineral sample provided no tungsten is present. If a mineral containing appreciable titanium is test,-!d in the same manner, the solution in the crucible becomes violet. In the presence of columbium, titanium at first causes a violet coloration of the solution, which after a few minutes is masked by the stronger blue of the reduced columbium oxide. Although tantalum oxide (Ta205) does not interfere with the columbium test, tungsten gives a blue color that is indistinguishable from the color obtained with columbium. A simple method is available to detect the presence of columbium in the absence of tungsten, but when the presence of tungsten is suspected, the sample must be subjected to somewhat more elaborate chemical tests to determine the presence or absence of columbium. Although these latter tests can be made in the field, several steps are involved that arc best performed in the laboratory with simple equipment.

Jan 1, 1962

By H. I. Aaronson, S. Toney

When the component grains of .ferritic hicrystals of an Fe-1.55 pct Si alloy are disoriented through an angle "6 " about a conzmon [ll0] axis, the tendency for preferential growth of austenite crystals along the grain boundary during transformation at elevated temperatures is small when 11 deg, but increases rapidly at larger angles. This type of orientation-dependence indicates that grain boundary diffdsion promotes preferential growth along large-angle boundaries. Morphological differences between austenite crystals formed at small-angle [1101 and [loo] boundaries suggest that precipitate morphology can be dependent on the dislocation structure of the boundary. ThE morphology of precipitate crystals nucleated at a grain boundary can be significantly affected by the structure of the boundary.' The limited amount of experimental evidence available in the literature indicates that the morphological effects of boundaries made up of arrays of dislocations, such as subbound-aries and small-angle grain boundaries, are different from those of boundaries having essentially disordered structures, i.e., large-angle grain boundaries. On the basis of indirect evidence, it has been concluded that large-angle grain boundaries give rise to the formation of grain boundary allotriomorphs (crystals which nucleate at grain boundaries, and grow preferentially and more or less smoothly along them)2 in the proeutectoid ferrite and the proeutec-toid cementite reactions in plain-carbon steels, and apparently also in many non-ferrous alloys.' At small-angle grain boundaries in a plain carbon steel, on the other hand, ferrite crystals were found to take the form of primary side plates. Similarly, Guinie, loys. Primary sideplates formed at a subboundary with a constant orientation tend to be parallel to only one, or occasionally two matrix habit planes, and a marked change in the orientation of the boundary is accompanied by a change in the habit plane. Previous studies on the morphological effects of grain boundary structure were performed on poly-crystalline aggregates. Information on the disorien-tation of the pairs of grains forming the boundaries at which the various morphologies appeared in these specimens was largely either qualitative or semi-quantitative. Precipitate morphologies accordingly could not be accurately and systematically correlated with grain boundary structure, and thus theories which have been proposed for the various morphological effects could not be satisfactorily tested. This investigation was undertaken in an attempt to remedy these deficiencies by studying the morphological effects of grain boundary structure with a method in which the boundaries are formed by matrix grains whose disorientations are known and controlled with reasonable accuracy. EXPERIMENTAL PROCEDURE The crystallographic requirements of this study were fulfilled by means of oriented bicrystals of silicon-iron. Disorientation of the component ferrite crystals was carried out about common, major crystallographic axes through angles ranging from 1/2 to 44 deg. The silicon content was low enough SO that the bicrystals could be partially transformed to austenite by heating to elevated temperatures. The silicon-iron used had the following initial composition: 1.55 pct Si, 0.04 pct C, 0.0031 pct N, 0.17 pct Mn, 0.020 pct S, and 0.002 pct P. The alloy was obtained in the form of 0.036-in. sheet. The procedures employed to prepare seed crystals in strips of this sheet, to reorient the seeds, and to grow them into bicrystals are essentially those described by Dunn and Nonken and aynes." The characteristics of the bicrystals are given in Table I. The "bicrystal type" indicates the crystallographic plane parallel to the broad faces of the strip in both grains and the crystallographic direction which was parallel to the long edges of the strip in both grains prior to disorientation. The angular disorientation of the grains, 8, which was performed about the direction normal to the plane of the broad faces of the strip, was measured between the [ 00l] directions. Orientation of the grain boundary, , was taken as the angle between the plane of the grain boundary and a plane containing the axis of disorienta-

Jan 1, 1962

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By W. T. Millar

"INTRODUCTION The purpose of the Star Lake project was to investigate, by geophysical surveying and diamond drilling, the magnetite deposits in the northwestern Adirondacks, the ultimate objective being to increase iron production in eastern United States,ACKNOWLEDGMENTSIn its program of investigating mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclu-sion. The Mining Branch, Lowell B. ""Moon, chief; conducts preliminary examinations, performs the actual investigative work, aid prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical and spectrographic analyses included in this report were performed at the Eastern Experiment Station of the Bureau of Lines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and under the immediate direction of Dr. Alton. Gobriel in charge of the laboratory service unit.The mineral exploration was under the general supervision successively of John D. Bardill, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch. The work was done under the immediate supervision successively of J. P. Ryan, N. A. Eilertsen, and W. T. Millar, project engineers."

Sep 1, 1947