Search Documents

By T. L. Joseph

Sulfur balances calculated from operating data covering thirty-five blast furnaces indicate that approximately 92 per cent. of the total sulfur charged enters with the coke, 7 per cent. with the ore, and 1 per cent. with the stone.. Most of the sulfur is carried from the furnace by means of the slag, the total amount eliminated being the product of the slag volume and the percentage of sulfur it contains. Additional sulfur in the charge must be eliminated either by increasing the percentage of sulfur in the slag or the quantity of slag. From relations found between slag volume and coke consumption and sulfur in the coke and slag volume, curves have been prepared showing the relative value of blast-furnace coke as its sulfur varies from 1 per cent. CHARCOAL was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chiefly because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steelmaking process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace

Jan 9, 1924

By John J. Porter

The requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet and the dry. In each process, a stone storage is the first requisite of a successful plant. This storage place may handle the stone before or after crushing; its capacity may vary from two to three days' up to several months' supply, but it should be so designed that it can be filled as desired by the chemist and drawn at such points as will give a mixture of the various kinds of stone coming from the quarry and a reasonably uniform material going to the mill. The size of the storage place and the method of handling should be varied according to the nature of the material.

Jan 1, 1925

By E. S. Moore

Although nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the discovery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world's nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important rnine at Creighton, in the Sudbury field, it was not until 1883 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficully in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the International Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By E. S. Moore

ALTHOUGH nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the dis-covery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world's nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important mine at Creighton, in the Sudbury field, it was not until 188.3 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficulty in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the Inter-national Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By F. C. Sturges

FOR some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are solved. Recently we have completed two 36-in. diam. core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years [ ] and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam. shafts were considered, but actual computations showed 36-in. diam. shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1947

By T. E. Godson

As this is the age of reform, a uniform mining law for North America is a moot subject for discussion at this meeting of the Institute. The question is one of peculiarly technical and, in many respects, local character. We all appreciate the value of the metal-producing industries and recognize the necessity and importance of a well-considered and evenly balanced mining law as a branch of our jurisprudence either for the Provinces or the Dominion as a whole. Mining has taken its place as a foremost industry and legislation that seeks to control and govern it is the concern of not only the active miner but the citizens of the state. A law that, through its charitable measures brings into being the prospector, the pathfinder and superstructure of all mining activity and industry, protects his interests, safeguards invested capital, and encourages and enforces development, possesses at least the salient requirements of a businesslike Act. The manner of doing so is, I think, one of local and internal concern. May I be permitted to say without presumption that of the five mining codes, or Acts, that we have in the Dominion of Canada born and bred within the Provinces of British Columbia, Ontario, Quebec, New Brunswick, and Nova Scotia, some of them could be materially improved. In many respects they do not measure up to the times; they were no doubt creations of merit at the date of their birth but they have not been clothed in seasonable raiment as the years passed by. It is a stern fundamental principle that all natural resources are the inalienable property of the crown. If it is mineral land, then it follows for the protection of the state and the direct advancement of the occupant that the land should be developed as such. The method or machinery by which this must be accomplished is a matter of detail, not of principle. If the right to possession as a licensee depends on discovery, it is not inconsistent with the duty the crown owes to, the state that a grant in fee should pass to the discoverer if there is imposed, after patent issues, a requirement of continuous work or the alternative of an acreage tax sufficiently burdensome to make it unprofitable that the land should be held in an undeveloped state. If, this requirement is recognized, the mental distinction between a grant and lease ceases to exist. A

Jan 4, 1919

By J. P. Witherow

MR. BIRKINBINE'S description of the bad working and sudden chilling of the Warwick Furnace last summer, seems to me quite phenomenal in blast-furnace practice. During my connection with the management of blast furnaces for many years, in the anthracite, coke, and raw-bituminous coal districts, such a case has never come under my notice. It seems to me that the scaffold in the zone of fusion could not have established itself (so that the whole power of the engines, with a blast pressure ranging from 12 to 18 pounds per square inch, could not penetrate), unless the furnace was previously badly scaffolded and bridged in some of its upper sections, from 15 to 30 feet above the hearth level, either in the zone of chemical action or the beginning of the zone of fusion. Such a "barrier to the upward gaseous currents would cause a suspension of combustion which may have superinducedd the scaffold that is assumed to have existed in the zone of fusion. It is Difficult to conceive' that an agglomerated mass almost across the section of the lower bosh should have formed all at once, if the furnace was free and porous for the reaction of the gaseous currents above. Therefore, I think, the Warwick furnace was by no means in as free, open, and fine internal condition at the time the trouble commenced as the description of its regular working would lead us to suppose. I do not question the accuracy of the statements relative to the output of iron, etc. I merely claim that the phenomena., as described, could not have been almost instantaneously developed, unless there had been an incipient seaffold and lodgment above the zone of fusion. I would state my hypothesis to be that the stock lodged or collected in some of its upper sections during the process of blowing-in, on which, as a basis, more or less accumulations may .have lodged, and thus, indirectly, caused the formation of the suc- * This paper was not presented to the Institute in its present form, but is based on remarks, in discussion, by the author on Mr. Birkinbine's paper on, a Short Blast at the Warwick Furnace, and Mr. Witherbee's paper on Two Scaffolds at the Cedar Point Furnace.

Jan 1, 1881

The aquifer at Phosphate Hill, north-west Queensland, presents special management challenges. The site contains a phosphate rock mine, fertilizer plant and camp. All of the site water is provided by the Duchess Embayment Aquifer, located within the Burke River Outlier of the Georgina Basin. The Duchess Embayment is a triangular shaped, Cambrian marine sedimentary basin consisting of siliceous and calcareous phosphorites, shales, siltstones and sandstones. It is fault-bounded on all sides and has a regional dip of 5¦E. The aquifer is largely confined to the siliceous facies of the Beetle Creek Formation. It has a very flat potentiometric surface and an average thickness of 45 m with confining beds above and below. The siliceous facies derives from weathering of the calcareous phase and is highly transmissive while the calcareous zone itself contains less water and is dependent upon interconnecting fractures for its permeability. Recharge appears to occur where the siliceous facies crops out around the edges of, and within, the Embayment. Aquifer management issues revolve around two points: successful dewatering of the orebody for mining; and efficient management to maintain water quality and ensure supply over the predicted 30-year life of the project. Current operations are extracting water at levels much below that originally estimated. This is having a detrimental effect on mine dewatering with the SWL lowering at a rate slower than anticipated. As a result, ore parcels are now beginning to intersect the water table, providing a major constraint to the mining plan. The aquifer drawdown cone is extensive and very flat so to keep the water table at an appropriate level for mining the management plan will include more aggressive dewatering to lower the level of the entire aquifer. The additional water will either be disposed of downstream or stored in a holding dam or via the use of artificial storage and recharge. Water resource management will also need to maintain the current quality. About 37 per cent of the water currently extracted forms the low chloride supply required by the ammonia plant and the power station. This ratio is expected to remain applicable under any future operating conditions but the low chloride resource is restricted so will require prudent management to enable the supply to continue. At current usage rates aquifer recharge versus use will need careful monitoring to ensure that the resource remains viable in the long-term.

Jan 1, 2003

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

By F. S. Sinnatt

This paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to play a definite part in the spontaneous combustion of coal in the goaf (waste). Tables 1 and 2 contain the analyses of samples of dust collected from a mine and from a dust collector. Some idea of the degree of fineness of the particles of fusain may be obtained from a study of the analyses of the dust from the dust collector; 80 per cent. of the dust would pass through a 200-mesh screen while the fusain was concentrated in the finest dust. The material that passed through a 90-mesh screen contained 54 per cent. of fusain while that between a 30- and a 90-mesh only con-

Jan 1, 1925

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

By G. W. Maynard

In this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporay suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our owu Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in september, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxiug materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slog." This is the keynote of the Siemens direct process. Dr. Siemens says further: " If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, arid the fusion of the earthy matter mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, weshall rind that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonsceous matter per ton of iron contained in the ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By Benj. F. Tillson

To most mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount of drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be SO handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau of Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 1, 1922

By E. J. Whittenberger, F. N. Rhines

The formation of casting porosity is viewed as a nucleation and growth process with solidification shrinkage and gas precipitation as cooperative driving forces. Experimental evidence evaluating the individual contribution of each force confirms the major premise that microporosity is nucleated by gas precipitation. Additional data disclose the effects of the identity and quantity of gas, the temperature range of freezing, and the freezing rate upon the amount and distribution of porosity in light metal castings. POROSITY, as it commonly occurs in metal castings, has been ascribed to the contraction that accompanies the freezing of the metal, to the evolution of dissolved gases from the liquid during cooling and freezing, and, most frequently, to a combination of the two.'" "Pipe" formation is universally associated with solidification shrinkage; spherical "gas holes" are understood to be retained bubbles of gas; but the origin of microporosity, which usually exhibits an irregular or scalloped outline when viewed in cross-section, remains a subject of continuing debate.", ' The present research constitutes an endeavor to show what parts are played respectively by shrinkage and gas evolution in the initiation and growth of micropores and what factors determine their number, size, shape, and distribution. A preliminary outline of the mechanism of cavity formation in castings will serve to coordinate the experimental findings that will be reported and will at the same time provide a general theory of the origin of casting porosity. Basic to the mechanism of cavity formation that will be proposed are the following established facts: 1—that liquid metals and alloys contract gradually during cooling down to the freezing range, where a relatively large contraction, known as the "solidification shrinkage," takes place (exceptions in bismuth and gallium being noted);' 2—that the capacity of liquid metals and alloys for dissolving gases diminishes with cooling until, in the freezing interval, a large decrease takes place (various exceptions being noted and excluded from present consideration) ;.: and 3—that freezing proceeds counter to the direction of heat flow, the freezing front most commonly being composed of a system of tapering dendrite stalks and side arms which are coarser the lower the freezing rate and which protrude into the liquid for a distance that is greater the longer the freezing temperature interval of the alloy and the smaller the thermal gradient.' The mechanism by which voids are generated

Jan 1, 1953

By Henry M. Stanley

The methods about to be described have been tested in practice, and are believed to be specially adapted to such extended topographical surveys as mining engineers in particular are sometimes called upon to execute. The assistance of Mr. H. 0. Flipper in the preparation of this paper, and his practical authorship of the second part, is hereby acknowledged. I. Photographic SuRveying. The writer was recently employed; together with Mr. H. O. Flipper, to survey the properties of the Plata-Reina de Sonora Mining and Milling Company, situated in the mining district of Las Planchas, District of Magdalena, State of Sonora, Mexico. These properties, now owned by an American corporation, of which M. W. Evans, of New Orleans, is president, and Richard A. Pomeroy is resident superintendent, are famous in the history of Mexican mining, as the place where planchus, or bolas de plata were foulld about the beginning of the last century. Ward, the English CILargh d7Affaires in Mexico from 1826 to 1828, writing at that epoch, says: "The idea [that the ores in the north of Mexico were richer than those in the south] probably originated in the discovery of the famous bolas de plata [balls of silver] of Arizona [Planchas de Plata de Arizona, a stock-ranch in northern Mexico], in the beginning of the last century, which was, and probably still is, believed in Europe to be one of those fables with which mining countries always abonnd. But the attention of the present government of Mexico having been drawn to the subject, a search was made in the viceregal archives, by order of the president, for the correspondence which was known to have taken place respecting it in the year 1736. This correspondence I have seen, and I have in my possession a certified copy of a decree of Philip the Fifth, dated Aranjuez, 28th May, 1741, the ohject of which was to terminate a prosecution, instituted by the Royal Fiscal, against the discoverers of Arizona, for having defrauded the treasnry of the duties payable upon the masses of pore silver found there. The decree states the weight of the balls, sheets and other pieces of silver discovered (bolas, planchas, y otras piezas de plata), to have amounted to 165 arroba, 8 pounds, in all, 4133 pounds; and mentions particularly one mass of pure silver, which weighed 108 arrobas (2700

Jan 1, 1892