Search Documents

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By Clarence Zener

It is customary to regard the stress-strain relation as consisting of two parts, thc elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.l,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwir-kung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants---e.g., Young's modulus— upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective. of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of anelasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1947

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By Clarence Zener

It is customary to regard the stress-strain relation as consisting of two parts, thc elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.l,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwir-kung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants---e.g., Young's modulus— upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective. of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of anelasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1947

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

By H D. Smith

T HE production of coal in Canada was slightly higher in 1964 than in the immediate past, and the major users continue to be the electric utility and metallurgical industries. There are continuing trends toward the increased use of cokes and chars in various metallurgical applications. Geological Research During 1964, the coal drilling program of the Research Council of Alberta (RCA) was concentrated in the extreme south of the Province (notably in the Milk River area and the region immediately to the northeast of this area). Field work commenced on June 1 and was completed at the end of September, by which time a total of 376 holes, aggregating some 48,500 ft., were drilled in 132 townships. Although no new major coal occurrences were intersected, the pro-gram yielded useful data for defining the extent of the known coal deposits in the area. Detailed results will be analyzed during the winter and reported in due course. Meanwhile, a full report on the

Jan 1, 1965

By G. Ferrara

The reserves of lead and zinc ores in the metalliferous district of Iglesias in south-western Sardinia are today estimated at about 30 million tons, grading from 4 to 10% Pb + Zn. Of these reserves, about 40% are in the mines owned by AMMI Sarda S.p.A. The working of these resources goes back to ancient times. Not infrequently, traces of old Roman workings and remains of ancient implements are come upon in the higher parts of some of the ore bodies. Exploitation of these mines on larger scale, however, dates from the middle of the 18th century. Initially, the more accessible zones of the ore bodies and the richer ores were worked - the galena and the rich oxidized ores (calamine* with 25-35% Zn), which were often found in large masses, the enormous empty cavities of which still remain. The poorer grade deposits have been gradually rendered workable by the development of technology - the perfecting of the

Jan 1, 1970

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By Oscar E. Harder

THE TERM "physical metallurgy' is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By C. Samuelsson, G. Carlsson

Characterization of dust from Boliden Mineral AB’s copper-plant in Sweden was carried out using chemical analysis, X-ray diffraction analysis, energy dispersive analysis and wave length analysis using electron microprobe equipment. Dust from four different locations was characterized: the electrostatic precipitator (ESP) after the roasting furnace; the ESP after the copper smelting furnace; from the copper converter ventilation bag house filter; and from the bag house filter collecting dust from the settling furnace and tap gas ventilation. The results showed that the dust is composed of small solid and/or liquid particles from the furnace reactor which have been transported with the process gas to the dust collecting devices. This portion of the dust is mechanically formed. It also contains compounds that have been vaporized in the process and then condensed from the process gas at lower temperature, chemically formed dust. The proportion of mechanical and chemical dust varies with the process generating the dust.

Jan 1, 2001

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010