Search Documents

By Tadeusz Cyrul

Results of a large scale compression test in situ are the subject of discussion. A cube of coal having an edge length of 1.5 meters was subjected to uniaxial compression tests in situ. At the same time both load and deformation were controlled. Deformations were measured on 60 short measurement bases, each 23 cm in length. The bases were uniformly distributed on the side surface of the cube, forming five horizontal rows and twelve columns on the development of the surface. Readings were taken from each gauge for each level of loading which was increased step by step. Due to heterogeneity of the rock, readings showed scatter. Scattered data were approximated by a plane, using the least squares method for each row separately and for the entire population of bases. Orientation of the planes are analyzed. The geometrical measure of the bending moment is introduced. It shows that the magnitude of the bending moment and the bending plane differed from row to row, thus implying that the cube was not only bent but twisted as well. This complex behaviour of the coal cube is apparently caused by its heterogeneity and vertical anisotropy. The results constitute a contribution to the verification of existing design criteria on the stability of mining pillars.

Jan 1, 1984

By George E. Aiken, B. R. Jr. Waples

INTRODUCTION In this paper the author will attempt to bridge from the paper work of design and engineering to the reality of implementation. Certain facets of construction are constant to a successful project, no matter the level of technical complexity. Basic to timely, low cost construction are the people assigned to the project. Construction is not accomplished by robots, computers, or speeches; but rather by people. People do however require the avail- ability of equipment and communications to properly complete the work. ORGANIZATION Good organization is the basic requirement of a well implemented construction project. For this paper the author will suggest an organization chart as well as an activity listing that together support the construction activities. There is little difference in the activities or functions needed to construct a small plant or a large one. It is a matter of how much time an individual has to spend on an activity that determines the structure of an organization. The difference between a large and small plant construction job is often described as the multiple hat versus the single hat philosophy. As an example, a resident construction manager on a small job might be the manager, the field engineer, the scheduler, the estimator, and the procurement manager. At some time during a construction

Jan 1, 1986

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

As you are all aware, the theme of this con- ference is "International Resources Management". The subject matter of this particular session is "the mineral equation". Looking down the sub- ject matters and individual papers to be presented by other speakers in other sessions over the course of the conference, each particular item scheduled is in fact one of the variables that form an integral part of the total and complex mineral equation. Questions of reserves and resources as related to consumption must be viewed in the light of all those variables. Policy decisions taken by Government and eventually industry in these various fields will in themselves have their own impact on the defining of resources, and their ultimate availability to meet the needs of society by way of consumption. Undoubtedly, by the close of this conference, those of us in attendance will be better informed on the problems that confront the international minerals industry in the years ahead. Hopefully, we will have a better understanding of the views and philosophies of the wide range of participants in the industry-Government, private enterprise, and individuals who ultimately through their per- sonal aspirations in respect of their day to day needs will provide the final determinant as to the scope of the minerals industry.

Jan 1, 1978

By Steven J. Page, Robert A. Jankowski, John A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since initial verification of this health risk in coal mines by the Mine Safety and Health Administration (MSHA) during the early 1980’s, the Bureau of Mines has conducted numerous studies in underground mines to identify the sources of quartz dust and its fundamental characteristics. The most significant underground quartz dust source was found to be the continuous miner excavating rock. The percentage of quartz was also found to be higher in the smaller size fractions of the dust when significant amounts of rock was mined by the continuous miner. Furthermore, the quartz content in the continuous miner return remained fairly consistent at greater distances from the face. Another important factor speculated to affect quartz dust generation and its size characteristics is the morphology of the quartz bearing rock. The quartz content of dust between mines had notable differences with respect to the differences between kaolinite content in the dust. Low kaolinite content was associated with higher quartz content and increased size segregation of quartz into smaller dust particles, indicating that the free silica bonding matrix in the rock is most likely another factor responsible for quartz dust produced through mechanical comminution.

Jan 1, 1991

By Basil Prescott

A thorough knowledge of the peculiarities of this type of orebody is necessary in sampling these limestone replacement deposits. Oxidized ores are often overestimated because of error in determining specific gravity and actual cross-section of the orebody, and sulfide ores are often underestimated because it is difficult to scatter the samples so that they will accurately represent the area under consideration. This paper describes various methods of sampling and cites factors that enter into the estimation of these deposits. IN THE science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each successful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation.

Jan 3, 1924

By Vincent T. Ricca, Kurtis Chow

When dealing with acid mine drainage as to treatment levels, costs, and evaluation of abatement schemes, predictions of the quantity and quality of the discharges are needed. An acid mine-drainage model is presented in this paper. In essence, the model is a hybrid of computer programs for stream flow simulation and acid mine drainage. Two major aspects of the model are discussed: mine-water generation and acid-load production. The former is based on hydrologic concepts and the latter on pyrite oxidation kinetics and oxidation product removal. The total model is programmed for the high-speed digital computer. The major inputs are: climatological, basin characteristics, and mine characteristics data. By the use o f the hydrologic model the amount of water that flows through the pyritic system is determined. From this information, acid loads removed by leaching, inundation, and gravity diffusion are then predicted. The outputs from the total model are: average daily mine-water discharge, the associated acid concentration or load, plus the average daily flow in the receiving streams or at basin outlets. The capabilities of the separate models have been tested individually and the joint model has been applied to a small drift mine in southeastern Ohio.

Jan 1, 1975

By E. De Golyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is one of selecting test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favor- able, were usually found in anticlinal types of structure. This very understandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in parallel planes. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades, the majority of the known important oil deposits of the world have been discovered. This is but an incomplete, and the simplest, statement of the problem. Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps- anticlines, faulted structures, salt domes, etc.-but by

Jan 1, 1932

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

By Y. C. Kim

For the past few years, the Cyprus Bagdad Copper Company began experiencing a significant "ore-dilution" problem from its low grade open- pit copper mine located at Bagdad, Arizona. To pinpoint the causes of this dilution, a study was initiated to investigate as well as to improve in-pit ore-waste selection-procedures using conditionally simulated ore-bodies. Prior to the actual use of conditional simulation; a comparison of different estimation methods for a mined-out area in the pit was performed. Specifically, kriging estimates were compared against the original estimates of the company which were based on the polygonal approach. The results of this comparison clearly identified part of the so- called "ore-dilution" problem, which was the initial over-estimation of average ore grades from blast rounds, using the polygonal approach. The results from the use of conditionally simulated orebodies demonstrated that the "ore-dilution" problem can be reduced by more than half if in-pit ore- waste selection is based on the kriged estimates rather than the polygonal estimates. This simulation study also showed that the current use of the polygonal approach has the effect of shipping a larger tonnage of lower grade material to the mill.

Jan 1, 1982

By Matthew Spedding

The complex nature of the carboniferous measures prevailing in the U.K. has dictated the types of mining required to exploit the coal seams. Most mines in Britain are referred to as deep mines in the sense that they operate at depths of 1800 - 3000 feet. The main system of coal transport to the surface is by vertical shafts which intersect the workable seams which at times number between 4 and 5. As mining has been practiced in most of the major coalfields in the U.K. for well over 100 years, with the initial extraction of the shallower and more profitable seams, the present management have been left a legacy of indiscriminate extraction which severely hampers their efforts to maximise the mine layouts. There is no single standard design of mining layout capable of meeting the wide variety of conditions which exist in the British coalfields. Mining layouts are subject to fixed and variable parameters. In discussing multi-seam working, the main parameter must be the effect of old workings above and below the seam to be extracted. There is a distinct lack of reliable information which would enable layouts to be designed to completely avoid or control these destructive forces. The guidelines are, therefore, mostly empirical.

Jan 1, 1977

By Ho-Sang Sohn

Copper concentrate particles of 200 to 300 mesh size were fed from the top of vertical reaction tube of 2.8 cm ID and 2 m long with an O2-N2 gas mixture. The reaction tube was heated to 900 K to 1100 K. The residence time of the particles in the reaction tube was about 1 second. The copper concentrate particles were very rapidly oxidized and melted down during their descent in the reaction tube. The particle temperature were calculated by combining an un-reacted core model, mass transfer between gas and particles, and heat transfer between gas, particles and tube wall. The particle temperature reached its maximum within a distance of 60 cm from the top of reaction tube, and it attained at 2000 K at higher oxygen partial pressure. The most particles were melted at the oxygen partial pressure above 20 kPa. An appreciable amount of As, Sb and Pb in the concentrate particles was eliminated in the upper portion of the reaction tube and the rate of elimination are explained by the rate of mass transfer of volatilized species through the gas film on the particle surface and the variation of particle temperature during the descent.

Jan 1, 2006

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

By Pranav Deshpande

The wear behavior of metal matrix composites differs from that of the monolithic metallic counterparts because composite materials have multiple constituents in their structures and these constituents wear at different rates. It was observed that under low wear stresses, abrasive wear prevailed. As the wear stress increases, pullout of reinforcement occurs and both abrasive wear and wear due to pullout contribute to the overall composite wear. A model of wear taking into account both types of wear has been developed. A critical pullout wear stress was suggested for each composite. Below the critical wear stress, no pullout of reinforcement occurs. It turns out that the critical wear stress simply equals to the ratio of the interfacial strength between the matrix and the reinforcement to the friction coefficient between the reinforcement and the wear counter surface. The critical wear stress is independent of the particle size of the reinforcement. From data on wear of 53% WC composites, the equation of wear for 32% WC composites was obtained. Experimental results agreed well with the predicted wear rate of this composites. This provides an excellent verification of the wear model developed by Lin and Deshpande. Wear data from Modi et al. in the literature were also perfectly fitted with the model.

Jan 1, 2006

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By A. V. Tarasov

The nonferrous metals industry has been a sector with one of the highest growth rates during the recent years. The prospects for the Russian metals industry during the period until 2010 are associated first of all with a growing domestic demand for its products. The technological level of the metallurgical operations in Russia is relatively low in comparison with industrially developed countries: the average energy requirement is higher by 20% to 30%; the amount of generated waste in the process of rolled products manufacture is twice as high; the average labor productivity is lower by 2.5 to 3.0 times; the overall negative environmental impact is twice as high. Improvement of the technological level of the nonferrous metals production under the conditions of market economy is possible by application of innovative technologies for the development of this sector. The main trends for development of the nonferrous metals sector are: - meeting of more stringent requirements to the quality of concentrates; - more complete recovery of associated elements as commercial-grade products; - development of continuous process lines based on autogenous, resource-saving and environmentally safe processes; - use of combined technologies, including pyrometallurgical, hydrometallurgical and upgrading processes; - expansion of the fields of application for nonferrous metals and their alloys.

Jan 1, 2006

By J T. Carswell, N A. Schofield

Fluctuations in periodic reconciliations between the mine and the mill are an expected and common experience in mining and processing operations. These fluctuations are caused in part by errors in the estimates of tonnage and grade of the mined material as well as errors in the millÆs assessment of the material processed. Keeping these errors small and unbiased is an important aspect of an efficient operation whose primary goal is to derive maximum benefit from the exploitation of the mineral resource.These fluctuations in periodic reconciliations can also mask subtle but economically important problems which may take years to identify and resolve. Such problems can result from a poorly-conceived model of the mineralisation which affects both the spatial distribution of the ore as well as the tonnage - grade distribution over the range of cut-off grades. Poorly conceived models of the mineral resources and ore distribution can arise as a result of insufficient and inadequate?drilling and sampling of the mineralisation, inappropriate?application of geological?constraints in the estimation process and the use of inappropriate methods to estimate the block grade distribution. This paper presents three case studies from gold and copper mining operations, two of which experienced significant problems with their mine to mill reconciliations over extended periods of time. For the gold mine in case study 1, sampling problems were ultimately considered to be the main cause of the poor reconciliations between grade control predictions and the mill which persisted over a period of 18 months. In addition, incorrect application of resource modelling methods contributed significantly to a mismatching of the mill capacity with the mine at the beginning of operations. For the underground copper mine in case study 2, a change in the approach taken to resource modelling brought marked improvements in ore definition and more accurate predictions of ore grade and better production forecasts.The third case study describes the background to the expansion of production to exploit a large tonnage of lower-grade stockwork mineralisation in an open pit gold mine. Several years of favourable Mine to Mill reconciliation data from the mining and processing of higher grade and lower grade stockwork styles of gold mineralisation provided the confidence in the approach to grade control to support the expansion plans during a period of low gold prices.The paper is intended to complement the discussion of mineral resource estimation methods and risks in Section 6.1.3 of the Mine ManagersÆ Handbook to be published by the Australasian Institute of Mining and Metallurgy (Schofield, 2012).CITATION:Schofield, N A, Moore, J and Carswell, J T, 2012. Mine to mill reconciliation - Three case studies, in Proceedings International Mine Management 2012, pp 161-172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

The technology of coal preparation, while based on similar processes to those in common useage in the 1950s, has improved significantly over the past 15 years primarily due to advances in process control. This technology at least offers the potential for most coal preparation unit operations to be optimised to a considerable degree. However, to maximise the overall yield of an operation from pit to port, factors often outside of the control of the preparation plant operator have a dominant effect. Specific factors include an in depth knowledge of the feed characteristics of the various sources of coal, the detailed mine scheduling to provide an appropriate blend to the plant, and the interim handling and stockpiling processes between the mine face and the customer.This paper summarises the criteria for optimising the yield for a variety of mining, processing and stockpiling options, based on the principle of operating at constant incremental ash. Pragmatic operating assumptions such as extension of the principle to operating at a constant density for gravity operations will be discussed. A means of optimising the compromise between maintaining specification product ash to the customer and maximising yield by always washing at constant incremental ash, without the benefit of a homogenised feed, will also be Presented.

Jan 1, 1992