Search Documents

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By G. Baralis, P. Gondi, I. Tangerini, G. Scandola

The precipitation behavior of Zn-0.5 pct A1 alloy single crystals was studied by means of electrical resistivity measurements and by optical and electron microscopy. The single crystals for the resistivity measurements were prepared by an original method in - 100-p -thick sheets. The order of the precipitation kinetics ranged between 1 and 1.5. The dislocations play a relevant role in the first-order kinetics. Precipitation always occurs both on dispersed particles and on dislocations. Statistical examinations have shown that the first-order kinetics can have two different activation energies; i.e., the precipitation can have dz;fferent mechanisnrs which could not be identified, however, in the course of the research. During the tnetallographic exanzination of the precipitation structures a specific process of dislocation decoration was obsereed. The main purpose of this work was to study the contribution of dislocations to the precipitation. A number of authors have observed precipitation on dislocations and reference might be made to several monographs on the ubject.&apos;&apos; The possibility that dislocations also accelerate precipitation has been considered by Turn-bull3 and Fischer et al.4 The studies described in the present paper were carried out on zinc, chosen as a base metal owing to the ease with which dislocations can be introduced into it and because of the absence of excess vacancies after quenching in conditions where phenomena of accelerated precipitation still occur. Aluminum was preferred as alloying element because of the accelerated precipitation phenomena that resulted in a preliminary reearch. EXPERIMENTAL METHODS The observations refer to a Zn-0.5 pct A1 alloy. The zinc was 99.995 pct pure; a typical spectroscopical analysis is given in Table I. As a rule the alloy was subjected to homogenization, quenching, or slow cooling and annealing. Homogenization was carried out by heating at 390" to 410°C for 24 hr. From the homogenization temperature, some specimens were quenched and some slowly cooled at a rate of 2°C per sec. At this rate no precipitate was detectable under the optical microscope just after cooling. Quenching was carried out simply by dropping the specimens into water, aqueous ethylene glycol solution at -30" c, or liquid-nitrogen baths placed close to the homogenization oven. Vaseline oil baths were used with a thermal stabilization of 10-20 for both the aging treatments and the measurements; aging was generally carried out at 90" or 130°C. To avoid oxidation phenomena during heating, the vaseline oil baths had to be frequently renewed. The precipitation kinetics were studied by means of electrical resistivity measurements, using ans potentiometric method (reproducibility ± 5 x 10 5 v, that is 0.5 pct of the total voltage decreases on the specimens during precipitation). First, various types of specimens were tested, i.e., polycrystals, single crystals grown in capillary quartz tubes, and thin single-crystal sheets prepared by means of an original method requiring no container except for the natural oxide. Even if fully annealed, the polycrystals and the capillary grown single crystals showed resistivity in -creases, most probably due to dislocations introduced in the course of the measurements. Similar resistivity increases in pure zinc were noticed by another author. Only the single-crystal sheets showed no resistivity change; thus they were chosen for the subsequent tests. As already mentioned, these single crystals were obtained by using, as a container, the natural oxide on the zinc surface; the oxide strength is sufficient to maintain the original shape during melting with sheets up to 500 p thick. An initial zone melting and subsequent zone leveling, which led also to formation of the single crystals, were thus carried out on rolled sheets of the required thicknesses (- 100 p) and shape, lying on a flat silica surface. The resistivities were first evaluated by measurements at the liquid-nitrogen temperature. This method gave poor reproducibility, however, and this was attributed to the thermal cycles which had to be operated. To avoid cycles and handling, it was therefore decided to make measurements directly in the annealing oil baths; this required thermal stabilization at ilo-&apos; "C. In this way only the resistance changes were measured. Specimens of pure zinc and of completely annealed alloy were always examined as controls together with those under consideration; only those measurement runs were taken into account where the reference samples showed no resistance increases. Again, the main inconvenience was due to oxidation and this was avoided by renewing the oil baths; even so data reproducibility was poor and the observations were therefore carried out on a large number (many hundreds) of specimens so as to provide indications of statistical value. For the transmission observations under the elec-

Jan 1, 1969

By R. W. Fountain, W. D. Forgeng, G. M. Faulring

Precipitation of the phase Co3Ti (Cu3Au type) from a Co-5 pct Ti a11oy has been investigated using single-crystal X-ray diffraction techniques. Oscillation and transmission Laue patterns of specimens aged for short-time periods at 600" C indicate the formation of titanium-rich and titanium-poor zones coherent with the {100} matrix planes. Longer aging times at 600° C establish that the equilibrium phase also forms on the {100} matrix planes as platelets. These observations are corroborated by electron metallography; electron diffraction studies show the phase Co3Ti to be ordered. A probable sequence of the precipitation reaction is discussed. A previous publication by two of the present authors reported on the phase relations and precipitation in Co-Ti alloys containing up to 30 pct Ti.1 The results of this investigation established the existence of a new face-centered cubic inter metallic phase, ranging in composition from about 17.0 to 21.7 pct Ti at temperatures below 1000° C The decomposition of the fcc supersaturated solid solution was studied employing hardness and electrical resistivity measurements. The changes in hardness upon precipitation in alloys containing 3, 6, and 9 pct* Ti were found to be associated with an initial increase in hardness followed by a plateau and then a second, more pronounced hardness increase. Investigation of this behavior by electrical resistivity measurements suggested that two different kinetic processes were involved, which, when interpreted in terms of the kinetic relation,2-4 indicated that initial precipitation was in the form of thin plates. On continued aging, the plates impinged during the growth process. The general features of these findings have been confirmed by Bibring and Manenc,5 while, in addition, they report the phase to be ordered. The present investigation was undertaken to provide more definite information on the structural relationships between the precipitate and the matrix. EXPERIMENTAL PROCEDURE Single crystals of a (20-5 pct Ti alloy were prepared from the melt employing the Bridgman technique. Poly crystalline rod, 1/2 in. in diam, prepared from vacuum-melted material, was machined to 3/8- in. diam to remove any surface contamination that may have resulted from hot-working. The crystals were grown under a purified hydrogen atmosphere in high-purity alumina crucibles heated by induction. Considerable difficulty was encountered in attempting to grow monocrystals because of the high melting point of the alloy and the high solute concentration. However, one crystal about 6 in. long was obtained which was essentially a single crystal except for one or two very small grains around the periphery. The as-grown crystal was solution heat-treated for 24 hr at 1200°Cin a purified argon atmosphere and water-quenched. One-quarter-in. slices were taken from each end of the solution heat-treated crystal for chemical analyses, and the remainder of the crystal was mounted and oriented by the back reflection Laue Method. The chemical analysis of the crystal was as follows: Pct Ti Pct 0 Pct C Pct N Pct H Pet CO 5.29 0.08 0.004 0.002 0.0003 Balance By proper tilting of the crystal, it was possible to obtain slices 1/32 in. thick of [loo] and [110] orientation. The solution heat-treated crystal slices were sealed in silica capsules for the aging treatments, with titanium sponge placed at one end of the capsule to act as a getter. All slices were water-quenched from the aging temperatures, the capsules being broken under the water to ensure a rapid quench. Thinning of the slices for transmission X-ray studies was accomplished by a combination of mechanical and electrolytic techniques, the final thickness being about 0.1 mm. Laue patterns of the solution heat-treated crystal indicated that no strain was introduced by the thinning technique. ELECTRON METALLOGRAPHY After X-ray examination, the structural changes attending the precipitation were followed by examination of direct carbon replicas of polished and etched surfaces of the single-crystal slices and extracted phases. The earliest indication of significant structural change was observed after aging at 600°C The structure of a heavily etched, solution-treated crystal is shown in Fig. l(a). Aside from the etch pit pattern, no regularity of background structure is observed. On the other hand, in the background of the specimen heated for 500 hr at 600°C, the etching pattern shows a directionality indicating the influence of minute precipitate particles, Fig. l(b). On electrolytic dissolution of this specimen in 10 pct HC1 in alcohol, a large volume of very small, flattened cubes

Jan 1, 1962

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak&apos;s4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis&apos; solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By R. J. S. Brown, B. W. Ganison

A new logging method has been developed, based on measurement of the nuclear magnetism of formation fluids. The nuclear magnetism log (NML) is the only log that responds solely to formation fluids. It operates equally well in both oil-base and water-base muds and in empty holes, and can be used in all kinds of formations except strongly magnetic ones. Two separate NML measurements can be made, one of which provides a continuous formation fluid curve. This fluid curve is called the free fluid log (FFL) and is believed to indicate a minimum effective porosity in most formations. The FFL not only delineates fluid-containing zones, but provides an excellent correlation curve that can be obtained under conditions where conventional correlation logs are ineffective. Preliminary tests indicate that the second kind of NML measurement may help distinguish oil and water zones and provide information concerning permeability and wettability. (The FFL itself appears to provide some information on permeability.) The second kind of NML measurement requires stopping the logging tool for a short time opposite a zone of interest and taking more extensive NML data that can be displayed as nuclear magnetic relaxation curves. In some instances, oil and water saturations for the region immediately adjacent to the borehole can be read from these relaxation curves. INTRODUCTION In 1946, Bloch, Hansen and Packard and Purcell, Torrey and Pound3 independently announced the successful demonstration of the phenomenon of nuclear magnetic resonance. During the past 13 years, there have been many applications of nuclear magnetic resonance, including applications to the study of chemical structure and to the measurement of magnetic field strengths. Preliminary experiments on the feasibility of using nuclear magnetism measurements in well logging were made independently by California Research Corp. and Varian Assoc., the Varian work being sponsored by the Byron Jackson Tools, Inc. Since then a cooperative research program on nuclear magnetism logging has been carried out by the Byron Jackson Div. and Research Center of Borg-Warner Corp., and California Research Corp., subsidiary of Standard Oil Co. of California. The use of nuclear magnetism in well logging is of special interest because it offers a way of making direct measurements on the hydrogen in the formation fluids and not on the rock matrix. Within the past 1 1/2 years, successful measurements have been made with a research model logging tool in wells in California, Tex as, Utah, Louisiana and Wyoming. NUCLEAR MAGNETISM SIGNALS Polarization, Relaxation and Precession Many atomic nuclei possess magnetic moments and spins; that is, they are similar in some respects to bar-magnet and gyroscope combinations. Molecules and their nuclei are subject to thermal motion, which has a scrambling effect, tending to leave as many nuclear spins oriented in any one direction as in any other. However, if a magnetic field is applied, the magnetic nuclei tend to align in the direction of the field. The scrambling and aligning forces compete with each other, with the result that a few more spins are oriented parallel to the field than in other directions. This gives a net magnetization, or polarization, which is directly proportional to the strength of the applied magnetic field (aligning influence) and inversely proportional to the absolute temperature (scrambling influence). When the magnetic field in, or temperature of, a liquid sample containing protons is changed, the new equilibrium value of proton polarization is not established immediately but requires an amount of time which depends on the nature of the hydrogen-containing materials. The process of approaching the equilibrium value of polarization is called relaxation.&apos;.&apos; Polarization is a vector quantity, and the components parallel to and perpendicular to the magnetic field must be considered separately. Relaxation of the component parallel to the field is called "thermal relaxation", or "longitudinal relaxation", and the corresponding time for this component of non-equilibrium polarization to decay by a factor of e (natural log base) is denoted T. The relaxation of the perpendicular component is called "transverse relaxation", and the corresponding relaxation time is denoted T,. The potential energy of a magnet in a uniform field depends on the angle the magnet makes with the field; therefore, a change of the component of net polarization parallel to the magnetic field involves an exchange of energy between the spin system and the thermal motion of the molecules, leading to the term thermal relaxation for the relaxation of this component. Suppose we subject a sample to a strong magnetic field at right angles to the earth&apos;s field for a time greater than TI. A polarization, thus, is established at right an-

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By PAUL P. ZElGLER

Rapid growth of the aluminum industry continued through 1948 with an acute shortage of the metal in all forms marking the year. Estimates based on shipments made during the first nine months indicate that, in 1948, the industry shipped more than two billion pounds of aluminum products or roughly four times the amount shipped in the greatest peacetime year prior to the war. The rapid expansion of the aluminum industry is particularly reflected in the production of sheet. Last year, the industry as a whole shipped an estimated 40 per cent more sheet than was produced in the peak war year of 1944.

Jan 1, 1949

By James D. Bennett

Relationships among mine and injured miner characteristics and HSAC&apos;s degrees of injury are examined for 91,404 injuries in under- ground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner&apos;s age, whether the miner was using powered equipment, the year which the injury occurred, and the location in the mine where the injury happened. Injury severity is not related to the injured miner&apos;s total mining experience, job experience, and experience in the mine in which the injury occurred.

Jan 1, 1984

The Coal Utilization review arrived too late to appear in the May issue. Coal utilization technology is improving due to the urgency with the 1990 Clean Air Act and the incentives provided by the Clean Coal Technology (CCT) program. Advances in the CCT are the subject of this report because of their broad industry application, support and involvement. Clean coal demonstration program Projects in the $5 billion Clean Coal Technology program are jointly funded cooperative agreements - not contracts - between government and industry. The industry participant in each project contributes at least 50% of the total cost. The participant takes primary responsibility for the project and is awarded any patent rights for inventions that may occur during the demonstration. The government, on the other hand, ensures that schedules are met, costs are controlled and project objectives are met.

Jan 1, 1991

Delay in classifying the war minerals claims geographically and by minerals&apos; has resulted because a part of the claims is in the hands of the commission which is holding hearings at points easy of access from the mining districts. It was necessary for the commission to take many claims for use at these hearings. Twenty days will be allowed claimants to file typewritten or printed briefs based on the record made by the commission&apos;s findings. At the end of twenty days, the case will be finally submitted to the Secretary of the Interior. No new facts will be considered, those which have been submitted to the commission only being given consideration. The Attorney General has issued a decision whereby only such claimants as were directly requested by the government to start operations will receive consideration under the War Minerals Act.

Jan 9, 1919

In May 1952, a total grant of $750 was made for the establishment of a scholar- ship in petroleum engineering for the academic year of 1952-1953, to be ad- ministered by AIME and to be known as the AIME-Socony-Vacuum Scholarship in Petroleum Engineering It will be given In the general field of petroleum engineering The scholar selected must be an undergraduate who is expected to complete academic work during the period of the award In other words, upon completion of the award period, the recipient is expected to be ready to enter industry The establishment of this Scholarship and the selection of the Scholar there under will Impose no ob1igation upon the Scholar or upon Socony- Vacuum with respect to employment The Scholarship is being administered by the Mineral Industry Education Division of the AIME

Jan 1, 1952

By G. A. REINHA

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-On studying this paper it has occurred to the writer that possibly it was the drilling of the test cores that produced the strains which affected in-juriously the authors&apos; unrested bars. They found that the machining had only a slight effect, but did they also investigate the effect of the drilling by trying rest applied to the bloom sections before the cores were drilled from then? The writer has heard of a similar effect of rest after machining on test bars from castings, and it would seem more reasonable that the ductility was increased because the rests relieved strains pro-duced in chilling the test cores from the blooms, than because of any peculiar combination of solidification and rolling strains in the blooms which did not exist in smaller billets.

Jan 11, 1919

By Mikael Ersson

A fundamental mathematical model of lance blowing on a bath surface has been developed with a purpose to increase the understanding of various phenomena in top blown oxygen converters. The model is based on the Navier-Stokes equations and turbulence is predicted using the k-model. In the present model the deformation of the liquid surface, caused by the impinging gas jet, is described using a VOF formulation. The mathematical model results have been verified by comparing predicted penetration-depth data with experimental results from physical model trials. The fluid dynamic modeling has also been coupled with the thermodynamic modeling to predict the reaction rate/distribution occurring in the vessel. The focus has been on carbon and a qualitative comparison of the predicted carbon content in the hot spot area and in droplets with experimental data from laboratory trials has been done.

Jan 1, 2006

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

By R. J. Manser

A mathematical model of a shaking table is being developed, for inclusion in a package for the simulation of gravity concentration. The general form of the modules and how they fit into the package is briefly described. The separation on a shaking table is controlled by a number of operating variables and the importance of these variables in the model development is discussed. The influence of wash water, feed pulp density, deck slope, deck amplitude and mass feed rate are reported. The form of the model is described being based on the probability of a particle of defined size and density reporting to a specific discharge site. The mathematical relationships which relate size and density distributions to variations in the operating parameters are presented. The use of these functions in the prediction of the performance of a shaking table is outlined.

Jan 1, 1986

By Theron Wasson

The Central Michigan area held first place in the state during the year. Midland and Isabella, the leading counties in 1932, produced most of the oil in 1933. The Porter field southeast of Mt. Pleasant and along the same structural trend saw the greatest drilling activity. In Porter during the year 117 new wells were drilled. Under proration these wells produced 3,583,617 bbl., or nearly one-half the total for the state, which has been estimated at 7,947,695 bbl. The Porter field is already outlined on all sides except the northwest. It probably reached its peak in 1933. Unless a new field of some magnitude is developed in 1934, Michigan will see a continuous decline. The Greendale extension to the old Mt. Pleasant field furnished the new flush for 1932. In 1933

Jan 1, 1934

By Thomas A. Post

The methodology of determining the optimum SX pumper-mixer system based on bench top, pilot, or small-scale solvent extraction systems, is demonstrated. The design of small-scale SX-plants is different than a full-scale plant. The difference is explained here. The use of dimensionless parameters Nh, Nq, and Np that describe the head, flow and power of the pumper is shown and how to use them for the scale-up. Additional data is required to determine the optimum operating range. Applications of this methodology were used to design well known currently operating SX plants. The emphasis on the optimization of hydraulic efficiency will be shown on examples, including how the hydraulic efficiency is affected when the throughput of the system goes beyond the design. Designs of all sizes of equipment will be shown which optimize the hydraulic efficiency.

Jan 1, 2003

The fall meeting of the Coal Division t was held at Pittsburgh, Oct 21-22, with the William Penn Hotel as headquarters The registration totalled 168 Secretary Parsons, George Otis Smith and J T Breunich were the official representatives from Institute headquarters Eighteen papers were presented There were five sessions altogether Monday morning and afternoon were devoted to papers on miscellaneous subjects, on Thursday morning there were two sessions, one on combustion of coal, the other on miming subjects, and on Thursday afternoon the outstanding feature of the meeting occurred when the members of the Division met in the Cathedral of Learning, University of Pittsburgh, to hear the prize-winning papers read by J F Bottomley, of Harrisburg, I11 , and William Bellano, of Crested Butte, Colo All the students of the School of Mines at the University attended this session The informal

Jan 1, 1937

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James-Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1934