Search Documents

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven't been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By R. E. Cook

This work presents the development and application of equations of the form developed by Martin1 to describe gravity segregation performance during natural depletion. One-dimensional depletion analyses are applied to several hypothetical reservoirs. Considerable attention is given to the changes in saturation distribution in the dip direction resulting from depletion at various rates. Vertical gas saturation distribution within a sand having vertical permeability is studied to illustrate conditions which provide For low gus-oil ratio production from wells selectively completed away from sand tops, as observed from well performance. Results of performance calculations are shown graphically and illustrate the rate sensitivity of the gravity segregation mechanism and the influence of reservoir geometry and withdrawal distribution. It is shown that for sufficiently high depletion rates gas saturation distribution in the dip direction is characterized by the formation of two discontinuities, or saturation "fronts"; the updip front being the gas-oil contact of the secondary gas cap and the downdip front occurring at a position dependent upon the reservoir depletion rate, withdrawal distribution and reservoir geometry. The gas saturation in the region between fronts is shown to continually increase with time, while that downdip from the lower front remains very low and relatively stable. The effect of increased depletion rate is to reduce the region of stable gas saturation and thus enlarge the portion of the reservoir producing with continually increasing gas saturation. Special attention is given to the performance of reservoirs having sufficient vertical permeability to permit liberated gas to segregate vertically within the sand section before proceeding in the updip direction. It is shown that reservoirs of this type are far less sensitive to depletion rate due to the mechanical control of producing gas-oil ratios afforded by selective well completions away from sand tops. It is shown that gravity segregation performance is adversely af- fected by decreasing reservoir cross-section area in the updip direction. It is also shown that down-dip withdrawal concentrations can restrict gas segregation rates in the dip direction. INTRODUCTION The natural depletion performance of several large producing reservoirs in Western Venezuela has unmistakably shown the significant role that gravity forces play in governing the gas-oil ratio behavior of individual wells and the over - all pressure-production performance of the reservoirs. Analysis and prediction of the natural depletion performance of these reservoirs is of great importance in determining the economics of pressure maintenance operations. In 1957, a method for the analysis of pressure maintenance performance was presented by Martin1 which, in the original and more general form of the equations involved, provides a physically sound basis for the analysis of one-dimensional gravity segregation performance during natural depletion. The work reported herein is an application and extension of Martin's outstanding developments to a series of hypothetical reservoirs in an attempt to explain the general behavior of the gravity segregation mechanism and the influence of such parameters as depletion rate, reservoir geometry and withdrawal distribution. The study considers two types of flow: "distributed flow", where vertical permeability in the reservoir is zero and fluids flow only in the dip direction while uniformly distributed over the sand thickness; and "segregated flow", where vertical permeability is sufficient to permit gas to segregate against the sand top before proceeding updip. This latter type of flow has been recognized as an important mechanism active in the massive sand reservoirs of Western Venezuela. ANALYSIS OF ONE-DIMENSIONAL DISTRIBUTED FLOW SYSTEMS For an inclined reservoir having zero vertical permeability, the velocities of oil and gas flow at any point in the reservoir can be derived from Darcy's equations as

By V. A. Josendal, J. W. Wilson, B. B. Sandiford

Two radioactive tracers have been tested as a means of determining core saturation in multiphase flow studies. Cesium chloride was tried as a water-phase tracer, but complications in its use in low permeability cores resulted from sorption of cesium by the core or water-wet pads. IodoI3'ben-zene proved very satisfactory as an oil-phase tracer. The synthesis of iodobenzene from the sodium iodide as received from Oak Ridge is simple and direct. The tracer is insoluble in water and there was no evidence of sorption by any of the core materials used. use of the method to determine saturation profiles during capillary and dynamic desaturations and relative permeability measurements on oil-water and oil-gas systems is described. Comparisons of the dynamic and capillary methods of relative permeability determination were made using the tracer to check core saturation and saturation distribution. Other experiments are also described in which mobility of the oil phase at various saturations was measured by displacing labeled oil by flowing inactive oil. Similar experiments were made using water labeled with cesium 134. INTRODUCTION To be fundamentally sound. any laboratory method of determining relative permeability must meet, among others, the following requirements: (1) the core saturation between the pressure taps must be uniform, and (2) there must be uniform pressure difference between the phases in the region between the pressure taps. In practice it may eventually be shown that appreciable departure from either or both of these conditions may be permitted without introducing sensible error. but the magnitude of such error remains to be established. There is need then for methods of saturation determina- tion which will determine the saturation profile in a core as well as the overall average saturation given by the gravimetric or material balance methods usually employed. Methods which have received consideration include resistivity, X-ray absorption, gamma ray absorption, neutron diffraction, and radioactive tracers. The resistivity method has use in the determination of profile, but needs checking by independent means.' The X-ray method has been used successfully, but requires elaborate equipment and calibration.23 4 At present gamma ray absorption is practical only for very large cores. The neutron methodo does not appear adaptable to measurement of saturation variations in short cores since it is a scattering method. Russell, Morgan and Muskat' employed radiovanadium in a study of the mobility of interstitial water. Coomber and Tiratsook used radioiodine as an oil-phase tracer and measured profiles in unconsolidated sand packs. ADVANTAGES OF RADIOACTIVITY METHOD A thorough discussion of the theory of radioactive tracers and the technique of using them to study the movement of fluids in sands is given by Coomber and Tiratsoos and need not be detailed here. The method requires less equipment than the X-ray method; the counting problem is similar, but the generation and regulation of the radiation, which is a major problem in the X-ray method, is not required in the radioactivity method. In the X-ray method it is customary to add up to 20 per cent of absorber, usually an iodine compound, to the phase to be labeled. while in the radioactivity method a mere trace is sufficient. A possible disadvantage of the radioactivity method is that a disproportionate amount of the activity comes from the portion of the core nearest the counter, whereas the X-ray gives a true average saturation in the region traversed by the beam. 011 the other hand, this characteristic of the radioactivity method renders it peculiarly adaptable to study of certain types of radial variations in saturation. As with the X-ray method, a tracer may be added to either the oil or water-phase. An oil-phase tracer is more generally useful. however. since it permits work on oil and gas in the

Jan 1, 1952

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid cobalt and a number of dilute cobalt alloys Was measured in the temperature range 1550" to 1700°C at nitrogen pressures to 1 atm. At 1600°C and 1 atm nitrogen pressure, the solubility in pure cobalt is 0.0047 wt pct [3.8 cu cm (stp) per 100 g Co]. The standard free- energy change for the solution reaction 1/2 N,(g) = gout pct in Co) is iF - 10,000 + 5.24 T cal per g atom N. The alloying elements Cv, Cu, Mo, Nb, Tu, W, and V increase the nitrogen solubility, while Al, Fe, Ni, and Si decrease the nitrogen solubility. THE solubility of nitrogen in cobalt was studied previously by Sieverts, Busch and Dodd,2 and Schenck, Frohberg, and Graf.3 Sieverts investigated the solution below the melting point of cobalt, and Busch and Dodd worked with the liquid metal; however, neither study found any solubility for nitrogen in cobalt. Schenck et al, reported a solubility of 0.005 wt pct N in cobalt at 1600°C. Seagle et al. 4 reported residual nitrogen in cobalt after electron-beam melting, although no reasons were ventured for the presence of this interstitial impurity. This investigation was undertaken to clarify these inconsistencies, and to provide additional data on atomic interactions in dilute metallic solution. EXPERIMENTAL PROCEDURE This study was well-suited to the Sieverts' method, which has not changed significantly since its introduction by Sieverts. 5 The apparatus was of the same design as that described by Humbert and Elliott, 6 with a reaction bulb similar to that reported by Weinstein and Elliott. 7 The buret was not water-jacketed, but the measured gas volumes were corrected for small changes in room temperature. The melt temperature was measured by a disappear ing-filament optical pyrometer sighted through a prism onto the melt surface. Temperature calibration was made based on a measurement of the melting point of pure cobalt taken as 1495°C. The difference between the reciprocal of the observed and the true temperatures was assumed to be a constant, neglecting the changes in emissivity with small additions of alloying elements. The total error in gas-volume measurement caused by accuracy limitations in reading the mercury level in the buret, variation in ambient temperature, and variation in melt temperature was about 0.5 cu cm. This represents approximately 10 pct of the total solubility, and is a larger relative error than in previous studies6-' because of the small nitrogen solubilities encountered in the present investigation. The source and purity of the materials used are listed in Table IA. Recrystallized alumina crucibles were used throughout the investigation. Examination of the crucibles after solidification of the melts showed no reaction or penetration. Alloying of the cobalt melt was accomplished with the dropping technique described by Humbert. 6 The investigation was started using cobalt from African Metals Corp. in shot form, but this material was not of sufficient purity and did not yield consistent solubility results. Sherritt Gordon Mines Ltd. cobalt was then used throughout the investigation. In experiments involving alloying elements which could react with oxygen dissolved in the melt, the cobalt was further refined by annealing at 1400°C in a dry-hydrogen atmosphere. This treatment, described by Woolley and Pehlke, 8 markedly reduced the oxygen content. The oxygen and nitrogen analyses of the cobalt used in this study are presented in Table IB. RESULTS Hot Volume. The hot volume was measured prior to each run and was 50 to 55 cu cm (stp) at 1600°C. It increased linearly with increasing pressure and decreasing melt temperature. Pure Cobalt. Measurements of the solubility of nitrogen in pure cobalt and the temperature coefficient of solubility are summarized in Table 11. At 1600°C and 1 atm nitrogen pressure, the solubility was found

Jan 1, 1967

By J. Kostuik, M. J. de Bastiani

The method of mining the uranium orebody at Denison mine in the Elliot Lake district of Ontario is discussed. Details of the development of haulage-ways and rooms are giuen, as well as methods of ore haulage. The milling and beneficiation stages are noted briefly. Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west, Fig. 1. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10" to 45" on the north limb and 10" to 20" on the south limb, Fig. 2. The Denison orebody, located on the north limb of the syncline, lies between 800 and 3000 ft below the surface. The main ore zone is within 50 ft of the Missisagi-Keewatin contact (see Fig. 3), and it varies in thickness from 6 to 32 ft. This ore zone has a composite dip of 19" to the south and is composed primarily of two pyritized conglomerate beds separated by a band of pebbly quartzite stratum. The upper conglomerate bed of the main zone varies from 2 to 15 ft in thickness, while the lower conglomerate varies from 2 to 12 ft. Over extended areas, mining is carried out over the entire section comprising the two conglomerate layers and intercalated quartzite; in other areas, the conglomerates are selectively mined, depending on the thickness of the quartz-ite. The ore zone contains approximately 6 pct sulfides and 80 pct silica. The predominant uranium-bear ing minerals are brannerite, uraninite, and an unidentified mineral (probably thucolite). Some of the uneconomic metallic minerals identified to date are pyrite, pyrrhotite, and chalcopyrite. MINE LAYOUT Shafts: Underground exploration and development (Fig. 4) were performed through two shafts 1/2 mile apart. The No. 1 shaft, sunk to a depth of 1856 ft with the main station established at the 1600-ft ore level, is a 250-sq ft, 5-compartment shaft capable of handling 4500 tpd. Two 5x5-1/2-ft compartments serviced by a 12-ft diam double-drum hoist, are used for hoisting 190-cu-ft bottom-dump skips in balance. A 30-man cage, offset by a counterbalance, operates within a 5-1/2x11-1/2-ft compartment. The fifth compartment is used as a manway, pipe, and cable-way. This shaft is also provided with an intermediate pumping station used during the initial mining phase as well as loading-pocket and spill-pocket installations and pumping facilities. The 480-sq ft No. 2 shaft, located down-dip from No. 1 shaft, has a 2776-ft depth. Serving as the main hoisting shaft with a maximum capacity of 9000 tpd, it has eight compartments, four of which are used for hoisting ore in 10-ton capacity bottom-dump skips. These four compartments, measuring 5x6-ft in section, are serviced by two 12-ft diam double-drum semi-automatic hoists. A 50-man cage is operated in a 15x8-ft compartment, and it is counterbalanced by a 12-ton weight. Two compartments are used for ventilation, manway, electric cables, and pipes. A station was constructed at the 1325-ft horizon of the No. 2 shaft for relay pumping. The main sta-

Jan 1, 1961

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By Ben C. Gerwick

This publication is intended to document recent innovations and technologies that have the best potential for effectively improving the quality of marine foundations while reducing the cost, time and risk of construction. Marine foundations originated in Neolithic times with the Swiss Lake Dwellers who constructed pile-supported houses, safe from invading tribes. The Queen of Babylonia built the first recorded bridge in 1500 BC across the Tigris. The foundations were large flat stones laid on the river bottom. About the same time in India, builders extended their water well techniques to the construction of ?well? foundations in the beds of their rivers. These were really the first open caissons; brick walls were built up in a circular ring while divers excavated sand from the bottom, sometimes at a depth of 100 feet. The Romans extended the clay-filled cribs of the Middle East to shallow cofferdams, which they sealed by underwater concrete made with pozzolanic cement from Mt. Vesuvius.

Jan 1, 2013

By H. L. Lovell, L. H. E. Weyher

Cyclones have been used successfully in the mineral industries to solve solid-liquid as well as solid-solid separation problems in the processing of fine particles. Substantial information is available about the operation of cyclones as thickeners, classifiers, and concentrators using a dense medium. However, very little is known about the operation of the cyclone as a fine coal concentrator not using dense medium. This application of the cyclone, namely to wash fine coal in water, requires that classification phenomena be minimized in order to arrive at an effective separation of the high density ash and sulfur-bearing mineral particles from the low density coal particles over a wide particle size range. The authors have investigated the role of feed pressure, orifice diameters, and vortex-finder length in the cyclone washing of fine coal (--1/4 in.) in water. The results of this investigation show that cyclone washing of fine coal in water is an effective unit operation particularly capable of reducing the inorganic pyritic sulfur content. The combination of hydrocyclones with complimentary equipment such as Sieve bends, shaking tables, and flotation units appears to be especially promising and may ultimately yield fine coal processing systems that could approximate the high recovery efficiencies of today&apos;s coarse coal cleaning circuits. In the future, fine coal beneficiation can be expected to receive even greater research emphasis as a result of increasing sulfur restrictions on all major coal markets. In a previous paper, work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal was discussed.&apos; The initial evaluation based on that wo-rk demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper selected test data were presented that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of the data as follows: (1) Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity-vs.-pressure drop expressions taken from the literature on classification cyclones. (2) The flow ratio was found to be the most important variable for the separation of the solids. Control of this ratio through various cyclone operating parameters is discussed. (3) The data on the product yield as well as the ash and sulfur assays from the tests were evaluated by means of correlation and multiple regression analyses. Because size-classification phenomena cannot be suppressed completely in hydrocyclone washers, product yield and assay data are regressed against cyclone operating variables separately for different size classes. These equations then reveal how the interactions of the cyclone operating variables vary in terms of the separation for different size classes. (4) Density partitions from additional tests were analyzed by supplementing product-size analyses with sink-float analyses of the separated product size classes. The evaluation of these data show how classification phenomena affect separation by density. The results demonstrate in particular the feasibility of the hydrocyclone washer for removing pyritic sulfur from fine coal. In addition to these specific findings, the investigation points up the value, in general, of using hydrocyclone washers in combination with unit operations such as screening, table concentration, and flotation. In order to make optimum use of the hydrocyclone washers and work out the most effective combination of unit operations, it is important to have careful flowsheet analyses corresponding to the given feed and product requirements. Analyses of this kind are now possible by means of computer simulation of flowsheets and other operation research tools. INTRODUCTION Before proceeding with the detailed treatment and evaluation of our results, it will be useful to review the fundamental aspects of cyclone separators and also restate the experimental procedures and data handling employed in these studies. Review of Cyclone Fundamentals: AS shown in Fig. 1, the basic components of cyclones commonly used

Jan 1, 1970

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By George S. Austin

Adobe, dried mud bricks, have been used since before historic time in the construction of dwellings. Building materials are normally evaluated for thermal performance based on measurements known as R- and U-values. The R-value is an indicator of the ability of a wall to insulate effectively and the higher the R-value, the better it is as an insulating material. The U-value, or value of conductance, is the reciprocal of the R-value and reflects the rate at which heat is conducted through a material. But the "heat capacity of the wall" must also be considered. This measures the length of time that passes before a steady state of heat flow is achieved. The effective U-value measures both the resistance to the transfer of heat and the capacity to hold heat. These latter value make adobe a far more interesting as a modern building material that was formerly recognized.

Jan 1, 1983

By J. C. Carrasco, M. Sánchez, R. Jara, F. Marquez, F. Parada, R. Parra, J. Palacios

In past years, Chile has been the largest copper producer in the world and for 2002 mining represented country average of 10 % of the GDP, accounting for 47 % of the total exportation. As copper sulphides are the main mining resources in the country, the metal is produced using the classical processes of flotation and pyrometallurgical extraction. Seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country produced1,522,000 metric tons of fine copper in 2002, approximately one half of total copper concentrate production, with a notorious environmental impact due to the great amount of slag produced during these extraction steps. In this work, a global characterization of copper pyrometallurgical slags produced and disposed of in Chile and worldwide is done, and the concept of total project development is considered to explain the scopes of the study, recovering different compounds and generating new activities around mining. The presentation is completed with the proposal of various methods and techniques being developed today in a joint project between smelter plants and the University of Concepción, with the support of the Chilean government and mining companies, addressed to generate new materials from copper slag. Recovery of copper, molybdenum, precious metals, silica and iron, that is the most abundant component of the slag, are the goals for this research. Metals, commercial compounds, alloys and different forms of iron oxides for steel industry are proposed products.

Jan 1, 2004

By Paolo Cavalcoli, Marco Ziller

"ABSTRACT: In the year 2010 the State of Denmark together with the Municipality of Copenhagen, launched a very important and complex Project : the complete construction of a new double Subway Line :the CITYRINGEN.Copenhagen is the capital with a metropolitan population of 1,9 million.This line is like a ring placed in the very town center which includes all the most historical and monumental buildings and churches, with a total length of 17 km, and the presence of 17 stations plus 4 service shafts.The buildings have been built in the last centuries in an area where the groundwater is near to the surface and there are lakes and channels: the techniques adopted were advanced for those times, but limited as far as regards settlements and resistance to horizontal movements.The soil consists in 2 main groups.1.Upper sediments of the glacial ages : thickness total = 5-20 m composed by clay- silt-sand-gravelcobbles- granite boulders and flint in blocs and in layers : frequency and size of these obstacles wherenot determined.2.Limestone layers : 2a. upper limestone : highly fractured ,highly permeable2b.Itermediate limestone : less fractured, medium permeability.2c. Lower limestone : almost not fractured, low permeability.2d Bryozoan limestone : composed by fossils with microscopic dimensionsIn all the limestone formations there are important layers of flint , having thickness variable up to 3 m and important extensions. Water : in a part of the areas of the Cityringen the water is drinkable and utilized in the public waternet.Pollution: there are polluted zones due to previous industrial activities. Benzene areas have been identified, and for those areas special protections against pollution have been implemented.METROSELSKABET ,the public owner of the Cityringen,has set as priority to operate for the construction of the Cityringen the full protection of the environment and the respect of all the stakeholders :Very strong limits for the exhausted gas emissions have been introduced, by far stronger than those applied from the State of Denmark, very strong limits for the acceptable noise emission. And last but not least very important safety measures and procedure to avoid any accident on site."

Jan 1, 2014

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

By Eduardo Poltronieri Trés, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Anderson Denadai Thomzini

The first industrial applications of roller presses at the comminution were in 1984 in the cement industry. Since then, the equipment has taken more space in the mineral industry. However, many challenges are still present in this equipment, more specifically regarding to ore breakage predictability. The application of this equipment in the pellet feed preparation is fundamental to increase the surface area (blaine index) of the mineral using reduced energy consumption. However, even after several pressing steps, it is still challenging to achieve granulometry in percentages required for the pelletizing process. Currently these levels are reached in wet milling processes, typically carried out in wet ball mills. For the of pellets formation in pelletizing plants, both pelletizing and the firing processes requires finer granulometry. The motivation of this work is to study the pelletizing process, comparing the physical quality of the pellets produced only through comminuted ore in roller press the pellets produced in conventional comminution using circuit with ball mill.

Oct 1, 2019

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By D. F. Malan, Y. Jooste

"SynopsisScattered mining was practised on Kusasalethu Mine (previously Elandsrand Gold Mine) prior to 1998, but at deeper mining levels it was no longer feasible, since it would have resulted in unacceptably high stress levels and energy release rates. Longwall mining was not adopted at these depths as the mine required a more flexible mining method owing to the highly variable grade and the presence of geological structures. A mining method was developed that consisted of dip stabilizing pillars for regional support, as well as bracket pillars to clamp geological structures. A strict sequence of extraction was followed and this, together with the particular layout, was called the ‘sequential grid mining method’. This method addressed two key problems, namely negotiating adverse geology and the erratic grade of the Ventersdorp Contact Reef (VCR) orebody. However, a significant drop in production rates resulted in the need for alternatives and improvements to the original mine design. Modifications to the design were proposed in order to increase production rates, and an investigation to consider the rock engineering implications of these modifications was conducted. The study indicated that the modified method, called the ‘multi-raise mining method’, appears to be feasible and might address some of the production problems that were experienced with the original sequential grid design. An analysis of actual seismic data showed no significant differences between the original sequential grid mining and the implemented multi-raise mining. The numerical modelling of the mining layouts showed slightly higher interim energy release rates (ERRs) and average pillar stress (APS) levels during the extraction process. The final values are nevertheless identical to that of the original sequence. The study also investigated the use of a modelled moment method to analyse future seismic trends. The study illustrated that the expected seismic trends will be very similar for the multi-raise method compared to the original sequential grid mining method. This study is nevertheless considered of a preliminary nature and ongoing monitoring and analysis of seismic data at the mine is required to verify the response of the rock mass to the modified sequence and increased extraction rate. In particular, future work needs to investigate the effect of mining rate (advance rates in individual panels as well as volume of mining in particular raise lines) on the level of seismicity."

Jan 1, 2015