Search Documents

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

Secondary blast holes are now being pierced in quartzite and sandstone quarries, using multiple hand-operated Jet-Piercing units supplied with oxygen, fuel and water from a compact mobile carrier. A unit of this type, operating in a Canadian quarry, enabled four Jet-Piercing blowpipes to pierce blast holes for two hours without shutdown. The piercing blowpipes used were developed by Linde Air Products Co., a division of Union Carbide and Carbon Corp. The mobile supply carrier was constructed by the quarry from specifications supplied by Linde and modified by the quarry operators for their particular use. Employment of the new self-contained unit, which allows up to four operators to pierce approximately 450 ft of blast hole without shutdown, accelerates rock removal operations. Normally, only two blowpipes are in operation at one time. Large boulders or ledges, which sometimes remain after primary blasting to hamper loading operations, can, in the case of certain hard rock, be prepared for reduction more rapidly with these new units than by any other means. A special feature of the new manual Jet-Piercing unit is the mobile gas and fluid supply carrier. It consists of a standard truck chassis fitted out with four banks of large standard-capacity oxygen cylinders, a steel-holding tank for fuel oil, and a gasoline-driven air compressor and tank for pressurizing the fuel oil tank. Cooling water for the blowpipes is supplied to the unit from a hose extension to the quarry supply line. Feeder lines from the oxygen cylinder manifolds and the oil and water tanks terminate in four sets of take-off stations on the control panel at the rear of the truck. As many as four hand Jet-Piercing blowpipes can be connected to the take-off panel by high-pressure rubber hoses. The hand Jet-Piercing blowpipe used with the mobile supply carrier is a highly portable device which can be manipulated comfortably by one operator. The blowpipe can pierce blast holes at rates up to 60 ft per hour, depending on the properties of the rock. Blast holes can be pierced at any angle from the vertical to the horizontal, making it necessary for the operator to drill from the top of the boulder. Hole diameter is held to approximately that which allows the use of a standard 11/8-in. diameter dynamite. The manual Jet-Piercing blowpipe has these important design features: a burner from which the combustion gases emerge at supersonic speeds (in excess of 6000 ft per sec); a hole-sizing shell which controls the minimum size of the hole and protects the copper burner; and a sliding shield which protects the operator against the steam and spallings ejected from the hole during the piercing. The Jet piercing process has been applied successfully in United States and Canadian quarries within the last several years as an advanced method of "drilling" blast holes.

Jan 1, 1952

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By M. Tirmarche, J. Brenot, J. W. Piechowski

INTRODUCTION Statistical analysis of results obtained by workers survey is very often limited to the determination of the collective dose and mean annual values. This information is not sufficent by itself for radiation protection purposes since the cumulative exposure of a worker during his working life is not taken into account. A more complete analysis would be obtained by considering both: [ ] These two notions are different. The former depends on the evolution of the protection with time and is related to annual limits (ICRP, 1977 and ICRP,1977 a). The second depends mainly on the works performed during the period of survey, the interference of protection evolution is weakened. So it is useful to foresee how the individual average annual doses would be when considering survey periods of 5, 10 years, or more. STUDIED POPULATION In order to analyse the two previously mentionned notions it is necessary to follow up a well defined population of workers which is continuously exposed to the radiological hazards on a long enough period. The selected population is that of the workers of the French uranium mines always present during the 1971-1979 period (9 years). The number of individuals is 937. The radiological hazards are: 1. exposure to radon and short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation. The workers of the uranium mines are exposed to these radiological risks in different ways according to the work performed. It is therefore necessary to subdivide the population into more homogeneous groups with respect to the radiological risks. Three groups are considered: - Group 1 : 227 individuals whose radon and dust exposures are always nil - Group 2 : 449 individuals whose radon and (or) dust exposures are different from 0 every year - Group 3 : 261 individuals represent a mixed category. Some features of these groups are given in table 1. [ ] The 937 followed individuals represent approximatively the half of the whole population of the French uranium mines. Taking into account the procedure adopted to select the studied population, it appears clearly that this population is not representative of the whole miner population. DOSIMETRIC RECORDS Three risk indicators are considered .Individual annual exposures to radon and its shortlived daughters. They are determined by ambient monitoring based on radon concentration measurements and recording of the times elapsed in the various workplaces. For each worker the annual exposure is represented by the mean annual air concentration and is expressed as a fraction of the maximum annual concentration (MAC). Given the administrative arrangements and the effective state of equilibrium between radon and its daughters, the maximum annual concentration is practically equivalent to 1 Working Level = 2.08 x 10- 5 jm-3. (UNSCEAR, 1977). . Individual annual exposures to long-lived ore dust which are also expressed in fraction of the maximum annual concentration. . Individual annual doses of external irradiation (X and [y] rays) expressed in mSv (= 10-3 Sievert). Irradiation monitoring is based on use of individual film badges.

Jan 1, 1981

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

The Enquirer of October 13, 1835 carried a letter signed "G," calling attention to the great number of Virginians who were leaving the state and to the lack of enterprise shown in not developing the ample natural resources available. He mentioned coal in particular and in closing said: "Besides the coal mines owned by individuals, the Black Heath company of colliers are carrying on extensive operations. Owing to the derangement of the currency, and the immense expenses incurred in boring and sinking new shafts, I understand that their dividends have not yet been so large, as they may be confidently expected in future.-Another company, under the title of the Midlothian Coal Mining Company, is now about being organized by the Messrs. Wooldridges of Chesterfield, for the purpose of establishing an extensive coal business. Having examined the lands embraced in the charter and the principles upon which the company is designed to be organized, I am persuaded that more productive stock can no where be found. The charter embraces a space nearly equal to a mile square, adjoining the mines of the Black Heath company, those of Mr. N. Mills, and those of Stone Henge, which space must contain coal of great thickness of excellent quality, as the strata of coal of those other mines pass through it; exhibiting a field so extensive, that centuries may elapse before it is exhausted. A shaft has been sunk on these lands, from which a very large quantity of the best coal is being raised. The terms of the charter require the Proprietors to sell one-half of these lands and mines, from the sale of which they will appropriate $100,000 as permanent capital, to purchase hands and engines, and to sink other shafts to work the property and thus going into operation with such decided advantages, as to produce a profit as great as a reasonable man should desire. Here is an opportunity for investing capital, which I think should satisfy the wishes of many Virginians who speak of emigrating. Will they not embrace it?-I have confined my remarks to the coal mines, because they are in the heart of our State, and their operations are familiar to many who can verify the statements. I might extend them to the other mineral treasures of our State; but if I do so, they must be reserved for another number, this being longer than I intended, and perhaps longer than you can conveniently find room for in your crowded columns. G." In January 1828 the Tuckahoe Canal Company was authorized to construct a canal along Tuckahoe Creek, from the James River up the stream about five miles; later this was amended to allow the use of the stream with a depth of water of two feet, no tow path was required, or provided: A toll of one cent per bushel was collected and the canal company made large profits. The service was so poor that in December 18, 1835, John G.,

Jan 1, 1942

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Steele, S. D. Brady

THE Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains mineable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon¬galia Co. thence south and southwest across the state to Wayne Co. near Huntington. The Pittsburgh coal is also mineable in the Upper Potomac region but is now practically exhausted there. The total mineable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13% billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio river as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern. West Virginia District comprising Wetzel, Monongalia, Marion, Preston, Harrison, Doddridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 188o (when the Monongahela River Railroad, now B. & O. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgantown and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Monongahela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of mineable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. ECONOMIC IMPORTANCE The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1948