Search Documents

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.' Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By Charles L. Mantell, George Ferment

This investigation determined the jeasibility of current-potential curves as an analytical tool for monitoving manganese electroicinning solutions for metallic impurities. Nine metallic impurities were studied: trickel, cobalt, silver, copper, zinc, molybdenum, catlmiun magnesium, and sodium. The individual effect of each metallic irzplrl,iLy on the standard point-izatiorr was determined for a range of 'concentration. Not all of Ihe impurities affected the polarization curve; correlation between transition current and cotrcetztration of impurity. Molybdenum had an uncorrelated effect on the polarization curie. The effects of binary mixtures of impurities were studied to see if the transition current of the mixture could be predicted. Interactions occurred between impurities which prei'etzted the pvecliction the transition current of tile rrlisLitr.e by additive laws. The polarization curve was shown to be sensitive to metallic impurities which affect the current efficiency of a manganese cell. THE application of current-potential curves in manganese electrowinning is not new but played an important part in the conversion of an inoperative large-scale pilot plant into a continuous comnercial operation.1"" The effects of trace metallic impurities in manganese electrowinning solutions on cathode current-potential curves,5-19 specifically nine impurities (nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium) were studied for a range of concentrations. Cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity: molybdenum had an uncorrelated effect. Binary mixtures of impurities were studied to de-termine if the transition current could be predicted from the values for the individual constituents. Interactions between impurities prevented the prediction of the transition current of the mixtures by an additive law. The polarization curve was shown to be sensitive to metallic impurities which affected the rurrent efficiency of a manganese cell. The electrowinning of manganese relies upon maintaining a high-purity electrolyte. Purification schemes were developed to remove all of the heavy metals, the magnesium and calcium. Concentration limits have been established for single impurities. With high-purity electrolytes, favorable cell efficiencies are consistently obtained; but with impure solutions there is a reduction in efficiency. With the rapid rise to commercial prominence of electrochemical processes, there has been a lag in developing rapid methods for determining whether an electrolyte is sufficiently pure for efficient electrolysis. The most sensitive test for impurities is the behavior of the electrochemical cell. Impure electrolytes will cause a serious reduction in cell efficiency, and in many cases metal deposition will be prevented or reversed. The effects of impurities are not usually evident until after long periods of electrolysis, resulting in a disruption of the process. A method which could predict the behavior of an electrolyte in terms of cell efficiency prior to reaching the commercial cell is needed. Van Arsdale and Maier," Allmand and Campbell,a1'22 and others attempted to develop an electrochemical process for manganese,"3"29 but all met with some degree of difficulty. Jacobs et a studied the effects of metallic impurities in manganese electrowinning. Plant methods were based on a 2-hr plating in a small electrolytic cell. The final method was based on a 24-hr plating run, performed in a relatively large test cell. Here, current efficiencies were calculated with and without impurities in the electrolyte, and the critical concentration was established as the maximum amount of impurity that the electrolyte could tolerate before there was a serious loss in efficiency. The amount of impurity that could be tolerated decreased as the plating time increased, indicating deposition of the impurity. This test duplicated the conditions of commercial practire, and was sensitive to impurities. Small amounts of impurities significantly affect the hydrogen overvoltage at a metal surface, increasing or decreasing it depending upon the nature of the impurity. ockris established the limit for the onset of poisoning at 10-l moles per liter. The effects of impurities were studied by potential-time curves at a constant current density. The technique did not lend itself to rapid analysis in that several hours were needed to establish stable potential-time curves. Serfass and coworkers3' developed calorimetric and spectrophotometric techniques for analyzing for trace impurities. Our method4'" is based on current-cathode potential curves produced by continuously changing the cell voltage at a programmed rate. Starting with a clean stainless-steel cathode, the cell voltage was initially adjusted to yield zero current: the program was then started and the current was plotted as a function of the cathode potential. Fig. 1 is a typical current-potential curve. In initial region A the hydrogen-evolution reaction predominates and the polarization curve

Jan 1, 1967

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.'s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.'s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,'" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer's eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By G. L. Fisher, R. Maddin

The rate of self-diffusion in silver single crystals during torsional strain was measured over a wide range of tenperatures and strain rates. The torsional strain was applied in a cyclic manner by reversing the divection of twist aftev a certain fraction of the total strain was reached. Surface roughening was substantially reduced in cyclically strained specimens compared with those strained entirely in one direction. Diffusion coefficients were determined using a special sectioning technique whereby slices could be removed parallel to the surface of a strained torsion specimen. The accuracy of the technique was first determined using roughened specinzens statically diffused to various penetration depths. Simultaneous strain-diffusion experiments were then performed over the temperature range 550' to 800 using strain rates of lo-' to 2.2 x 10' sec-'. The increase in silver self-diffusivity during torsional plastic strain was small. In only one case was the enhancement greater than twice the static value of the diffusion coefficzent. The enhancements increased slightly with decreasing tenzperature and increased with increasing strain rate. A dislocation pipe mechanism of enhancement was found to explain the present results satisfactorily. The magnitude of the enhancements and the tenzperatures at which they were observed suggests that a steady-state dislocation density of 10' to 109 dislocations cm-2 existed during the high-tempevature deformation. The diffusion coefficient in an fcc metal can be increased by 1) an excess concentration of point defects and 2) the rapid movement of diffusing atoms along grain boundaries and dislocations. Plastic deformation may be responsible for enhancements by both of these mechanisms. The results of simultaneous strain-diffusion experiments have caused a controversy over the magnitude of the effect of strain upon diffusion. Experiments reporting large enhancements have been criticized for the manner in which the diffusion coefficient was measured. Several of these experiments have been contradicted by other results obtained in a similar manner. No enhancement was reported by two investigators''' who performed their experiments at high temperatures where strain is expected to have little effect upon diffusion. A recent theoretical analysis3 indicates that strain enhancement by a vacancy mechanism will be small and exist only at low temperatures and rapid strain rates. It is doubtful whether any experiment has yet proven that strain enhancements can occur by an excess vacancy mechanism. In the present research, experiments were performed at extremes of temperature and strain rate in an attempt to measure enhancement of diffusion by strain. Self-diffusion of silver during torsional deformation was chosen since two separate investigations4j5 indicate that at least a small enhancement exists under these conditions. An accurate method of determining the diffusion coefficient, mechanical sectioning, was employed after a technique was devised to apply it to the roughened surface of a strained torsion specimen. First, the accuracy of the technique was determined for different penetrations (2fi). Then diffusion experiments were performed at temperatures between 550" and 800°C at strain rates of 10"" to 10"" per sec. I) EXPERIMENTAL PROCEDURE Preparation of Specimens. The experimental procedure detailing the growth of crystals, their treatment, and the annealing techniques during straining are contained in earlier publications.496 The dimensions and orientations of the torsion specimens are shown in Figs. 1 and 2. licatiin of Torsional Strain. The torsion procedure was changed from that used previously. The specimens were strained in cycles to reduce the gross distortion and surface roughening inherent in twisting to high strains in one direction. For all strains above 0.30, the total surface strain was obtained as follows: the specimen was twisted to 0.10 strain in a clockwise direction; the direction was reversed; the backlash in the torsion apparatus was taken up; and the specimen was twisted in a counterclockwise direction through the initial starting point to 0.20 surface shear strain in the opposite direction. The strain reversal took no more than 1 min to accomplish. The total accumulated surface shear strain was arbitrarily taken as the sum of the 0.10 strain in the clockwise direction plus 0.20 in the counterclockwise direction. Although cyclic torsional strain was beneficial, surface roughening and specimen distortion were not entirely eliminated. The variation in the diameter at various points on the specimen was often much greater than the depth of the diffusion zone. Since serious errors might result if specimens were sectioned in the usual manner, a technique of lathe sectioning was devised to allow sections to be taken parallel to planes of equal concentration.

Jan 1, 1967

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By F. H. Wilson, M. L. Kronberg

The low temperature recrystalliza-tion of very heavily rolled copper produces a fine grained structure with a high degree of preferred orientation. Additional heating to within a few hundred degrees of the melting point may induce an abrupt and pronounced increase in the grain size, with the resulting crystals having new orientations. This behavior at high temperatures is commonly termed "secondary recrystallization." Several investigations have dealt with the phenomenon arid have served to bare many features of the beha~ior.1-4 In general,observations have been made on the sizes and shapes of the grains, and data have been presented showing the existence of an induction period in isothermal experiments. Although it has been well established that the orientation before the change is statistically (100) 10011, the so-called "cubically aligned" texture, there is no such agreement on the orientation after the change. For example, Dahl and Pawlek1 describe it as being equivalent to an approximately 30" rotation about the [l00] axis of the ideal cubic texture which is parallel to the rolling direction, the resulting orientation being near (210)[001]; and Cook and Richards2 find an orientation of approximately (110)[L12]. Since the completion of most of the work to be reported in this paper, Rowles and Boas3 have published their ver] illuminating paper on "secondary recrystallization," in which they present convincing evidence for a third orientation and show that their esperiments give no evidence for either of the other two orientations. The orientation is described as equivalent to an approximately 30° rotation about a [ 111] pole of the ideal cubic orientation. The existence of a variety of reported orientations is not unique for copper, for a similar state of affairs exists for other systems that have been studied— aluminum, nickel, nickel-iron alloys, and others. It seems therefore that the existence of this variety does not necessarily constitute a contradiction, but rather indicates that different experimental conditions yield different results. The fundamental nature of the phenomenon has not been elucidated. However, it has been generally recognized that the large grains could be the end product of growth of a few select grains already existing in the sample in minor amounts—too small to allow detection—or that entirely new ones could be formed by a process of nu-cleation and growth. Existing experimental evidence does not distinguish between these two most apparent possibilities. Nevertheless, the former has been more generally favored largely because our current understanding of the state of an annealed metal has not made it seem reasonable to expect a nucleation event to occur at temperatures above those required for the primary recrystallization. Observations on the Preparation and Heating of Twin-bearing Cubically Aligned Copper The starting material used throughout. the investigation was a bar of OFHC copper, forged and annealed at 950°C. Visual inspection showed the grain size to be around 0.5 mm, and did not disclose any preferred orientation. A chemical analysis showed the following composition: Cu + Ag— 99.99 Pct S — 0.005 pct 0 — <0.005 pct For the preparation of cubically aligned copper, ¾ in. thick slabs were cut from the bar, heavily pickled in concentrated HNO3 and cold rolled to sheets about 0.012 in. thick. The reduction in thickness was approximately 98.5 pct. Standardized annealing techniques were followed. Samples to be heated were lightly dusted with alumina in order to prevent sticking and then sandwiched between 1/16 in. copper plates. The resulting sandwich was heavily wrapped with copper sheet, and then annealed in air. The protection was such that only very thin films of oxide were formed. That the associated light oxidation of the samples had no specific effect on the recrystallization behavior was shown by the similar results that could be obtained on annealing in highly purified and dried hydrogen. Two methods were used in bringing samples to temperature: (1) by placing the package directly in the furnace at temperature and (2) by placing the package in the furnace at room temperature, and then slowly increasing the temperature. The corresponding heating rates are illustrated in Fig 1, and will be referred to as "rapid" and "slow," respectively. Unless specified otherwise, all anneals will be of the former type. Metallographic examination was made on samples prepared by electrolytic polishing and etching as described in the Metals Handhook.* STRUCTURES FOUND BEFORE "SECONDARY RECRYSTALLIZATION" OCCURS Annealing the rolled material for 1 hr at 400°C produced a heavily twinned, cubically aligned structure, the grain size being of the order of 0.03

Jan 1, 1950

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,&apos; an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of&apos; calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10&apos; and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).&apos; Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.&apos; They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan&apos;gin&apos; using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By C. E. Sims

IN an earlier paper by Sims, Moore, and Williams: data were given to show that hydrogen contents of 0.3 relative volume (0.00033 wt pct), existing at the center of 4-in.-square cast-steel coupons, could be removed by aging at 400°F for 125 hr. At the end of that time, complete restoration of normal ductility for the steel was obtained. Replicate specimens of the same steel were aged at room temperature up to 555 days or .18 1/2 months. At the end of that time, the hydrogen content at the center had fallen to 0.13 relative volume or 0.00015 wt pet, but there was no perceptible change in the ductility. On the basis of experience with accelerated aging of 1-in. and 4-in. coupons and room temperature aging of 1-in. coupons, it was predicted that, some time after two years and when the hydrogen content has been reduced to about 0.10 relative volume, there would be some recovery of ductility. One set of three bars remained, and these were held for 1310 days, or more than three years. Then tensile test bars were cut from the center, and these bars were sampled for hydrogen analysis at the time they were broken. The sample specimens were cylinders % in. in diam x 1 1/4 in. in length. The data showed that in this time the average hydrogen content had fallen to 0.096 relative volume or 0.00011 wt pct, and the ductility had increased sharply. Elongation had risen from 10 to 17.3 pct, while reduction of area increased from about 16 to 27.5 pct. On the basis of these data, fig. 1 was drawn to replace fig. 15 of the earlier paper. Extrapolation of the curves of fig. 1 indicates that it would require a period of about 2200 days or approximately six years at room tem- perature to reduce the hydrogen to the minimum value and to recover full ductility in the center of the coupons. The aging process apparently involves the movement of hydrogen from the interior to the surface of the bar and evaporation at the surface. This flux of gas presumably follows some diffusion mechanism, and an effort was made to use the aging data, obtained at room temperature and at 400°F, to calcu-late coefficients of diffusion, in the hope that they might indicate the nature of the diffusion. The conclusion was reached. however. that the data were inadequate for such a purpose.

Jan 1, 1951

By L. D. Jaffe

THE data recently published1-" on heat treatment of titanium alloys have not been readily systematized into an overall picture. When the ß titanium phase transforms isothermally at low temperatures, the hardness follows a typical age-hardening pattern, going through a peak as schematized by the "hardness" vs "time of isothermal transformation" coordinates of Fig. 1. As the temperature is raised, the peak will decrease in height and occur at shorter times; slowing must however take place as the /3 transus is approached. The brittle microconstituent in the region of peak hardness has been termed /3&apos;. Its structure is still undetermined but it is clearly a transition stage from soft /3 to the £ + a that is found at the right of the peak. On continuous cooling, high cooling rates correspond to short times on Fig. 1; abscissa labeling has been added accordingly. Extremely rapid cooling will retain soft /3; very slow cooling will precipitate soft a; intermediate rates give hard 8&apos;. Increasing distance from the water-quenched end of a Jominy hardenability bar corresponds to slower cooling (right on Fig. I), but the range of cooling rates covered by a Jominy bar is only a small portion of that shown in the figure. The p-stabilizing alloying elements retard the transformation process, moving the material to the left on Fig. 1. A lean alloy is harder water-quenched (P&apos;) than air-cooled (/3 +a); a rich alloy is harder air-cooled (/3&apos;) than water-quenched (/3). Examples of the position of various compositions with respect to the curve, based on limited data in the literature, are given at the top of the figure. Oxygen and carbon accelerate the transformation process, moving the material to the right on Fig. 1. If an alloy quenched quickly enough to retain soft /3 is reheated below the £ transus (tempered), it ages, going through a hardness maximum as time increases (moving right on Fig. 1). Material which after cooling from the /3 range lies on or right of the hardness peak, will move still further right on tempering, and so soften. Since the rate of the tempering (aging) reaction increases with temperature, the figure also may be used to represent the variation in properties with tempering temperature, at short tempering times. The simple picture given here neglects martensite transformation, as well as differences between decomposition products of /3 formed by direct isothermal transformation and those formed by quenching and tempering. It may nevertheless be of use as a guide for practical heat treatment and for further research.

Jan 1, 1955

Discussion of the paper of CHARLES H. MACDOWELL, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 103 to 114. GEORGE S. RICE, Pittsburgh, Pa.-I am especially interested in the mining side of this important question. In 1911, when in Europe investigating mining matters, giving special attention to subsidence clue to mining, for there is a very big problem of that kind, as many of you know, in the Pennsylvania anthracite region, I visited Stassfurt, which is one of the chief centers of potash mining, and which was pointed out as the place to see surface subsidence. We found the town much askewsome of the streets having sunk from 15 to 30 ft., leaving many ancient buildings pitching at various angles. One old church, 500 or 600 years old, has been sunk about 20 ft., cracking it badly. I understand that this condition came about because in early mining clays they were careless about leaving proper supports and used no filling or packing. The Stassfurt mines work along a buried anticline the sides of which pitch at 45° on the average. Through this careless mining they had a break of the hanging wall which let in water from the overlying marls and sands. The water rapidly dissolved the salts in the pillars, and spreading through the entire chain of mines, caused their complete loss, with serious trouble for the old city. They had to start new mines some distance away, and take care to prevent roof caves. The packing system is of interest. They were driving large rooms into the rock-salt foot wall and using the rock salt as dry filling. The application of hydraulic filling, using a saturated solution, was under contemplation at some plant nearby. Whether 6r not the plan was carried out I do not know. I was reminded of the plan by Mr. MacDowell&apos;s remarking on the use of a saturated salt solution in the core drilling. His reference to the apparent breakdown of the potash syndicate raises an interesting question. We have had the German system of syndicates pointed out as perhaps one means of solving our troubles in the soft-coal mining industry due to overproduction. It seems to have worked out admirably in the case of the Westphalian coal-mining syndicate and also in the syndicate of Upper Silesia; but apparently the syndicate plan did not work in the potash industry. .

Jan 5, 1915

By J. W. Leonard

Comments The venerable straight-line equation Y = Bx + A is again being rediscovered, but this time by economists, mining engineers and geologists. Two economists, William Sharpe and Harry Markowitz, from the University of Chicago and Stanford University, respectively, won the 1990 Noble Prize in economics by showing that the price of individual stocks can be related to the Dow Jones industrial average (DJIA) using the straight-line equation. According to Bill Chidester, Investment Analyst, Scientific Investment, Sharpe and Markowitz strongly emphasized the role of the beta (B) value while considering the alpha (A) value to be "pretty unimportant." Chidester claims that alpha is the "mystery" value that causes individual stocks to behave independently of popular stock-market indices, such as the DJIA. For many years, mining engineers and geologists have routinely called alpha the "nugget" or surprise element in geostatistical analyses in which a designated distance (x-axis) is related to the variance of the grade (y-axis). Because the influence of the independent variable (distance) over the dependent variable (grade variance) is ideal when alpha is equal to zero, any increase in alpha represents a loosening of influence or control within the relationship. This can be good news or bad news - good news if you are an economist sorting out off-trend stocks and bad news if you are a mining engineer trying to predict sulfur in a coal seam. With many mining trends, such as those involving the relationship of distance to the variance of grade, a mathematical relationship can be formed. In geostatistical analysis, the point where a mathematical trend ends is known as the sill. If the difference between the variance of grade at the sill and at alpha can be determined, then an estimate of the relative control for a given distance can be obtained by comparing the sill value to alpha. The extent to which alpha approaches the value of the sill provides an indication of independence or loss of trend. The alpha concept may find application with distance, time or fluid problems. The point of change can be either a change in trend or the trend limit. However, even without a clearly defined point of change or trend limit, increasing alpha values always infer loss of trend. Alpha analysis should be regarded as a valuable tool when sorting out many sets of mining data. The application of this user-friendly concept to reserves, material transport, fluid flow and other areas has been, and will continue to be, the basis of many important past and future developments in mining and geology.

Jan 1, 1996

By Harvey S. Mudd

AMONG the highly skilled craftsmen of the Renaissance were those who worked with ores and metals. The author of this book, Vannoccio Biringuccio, was a master craftsman in the practices of smelting and of metalworking. Contrary to the customs of a trade, Biringuccio was moved to impart his knowledge to all and thus he has given us the earliest hand- book on metallurgy-in fact, the first printed book dealing with the applied metal arts and the processes of ore reduction. We should remind ourselves that metallurgy is an ancient art and then it fair1y may be said that Biringuccio sought to describe the techniques that had been in course of development since the Bronze Age of western civilization. Whether Biringuccio was a man of learning or a scholar according to the standards of his time we do not know, but today we recognize him as a man of science who gave his wisdom to succeeding generations. It was not until the coming of the Power Age at the end of the eighteenth century that progress was resumed in the science of which he wrote more than two hundred years before. Little is known of Biringuccio&apos;s training in his native Siena. It can be surmised that there, as in Florence, where his contemporary Benvenuto Cellini lived, he received his training in the craftsman shops where the industrial arts were taught and flourished alongside the fine arts. Perhaps he and Cellini were acquainted, although there is no mention of Biringuccio in Cellini&apos;s autobiography-an omission that Cellini&apos;s vast egotism makes understandable. He was the great artist, and Biringuccio was a practical, studious, unromantic figure with no favors to dispense. In the April 1940 issue of Mining and Metallurgy Dr. Smith describes Biringuccio&apos;s book under the title of "A Neglected Italian Metallurgical Classic." The article, revised and extended, forms the basis of the introduction to the present volume, and I urge all who take up Pirotechnia to read what Dr. Smith has written in the Introduction. Biringuccio&apos;s work is a classic and in its translation Dr. Smith and Dr. Gnudi have brought to bear the high degree of scholarship that it deserves. Dr. Gnudi made the translation at Dr. Smith&apos;s request and it was then refined "in the fire" of his scientific knowledge of the subject. The result is a book which the Institute is proud to place before its members and which the Memorial Fund Committee considers it a privilege to publish.

Jan 1, 1942

By E. P. Mathewson

DURING the past 35 years it has been my privilege to deal with hundreds of recent graduates from engineering schools all over the world. In consequence, I, feel that I have learned something about the training of, engineering students. In the first place, I believe that too great specializa-tion is a mistake. A student should receive general training in engineering for at least three out of the four years of the course, and any specializing that may be required should come in the fourth year. Too great emphasis can not be laid upon the fact that the four years&apos; training does not make an engineer; on the contrary, the graduate is only fitted to enter the pro-fession. He becomes an engineer in the true sense of the word only after years of practice; the college train-ing merely shows him where to look for information and develops his intellectual powers. Some of our engineering schools have lengthened the term of study to five years and talk of increasing it still further. This, in my opinion, is a mistake. A young man who spends more than four years in college is apt to become too academic and theoretical. It is better to stiffen the matriculation examinations than to prolong the years of study in college. No matter how good the faculty may be and how carefully selected the course of study, the graduate can never become an engineer unless he has some natural qualifications for the vocation. There are one or two subjects in which most recent graduates seem to be weak; these are accounting, the command of English, and training in the writing of reports. A short course in general accounting should always be included in the curriculum. To this should be added instruction in the preparation of estimates and cost statements. In making reports it should be borne in mind that these reports are to be submitted to busy men,-and not to technical men. The busy man wants the gist of the report summarized on the front page of the report. He wants to know that if he expends a certain sum of money in a certain way, he will get certain results and make so much profit. This should be put clearly before him in short statements, free from technical terms. The details of the report can follow .at greater length; it should be remembered that the employer is not going to read these details, but will confine his attention to the summary.

Jan 1, 1923

The Telfer Project, one of the world&apos;s newest gold mines, is located about 300 km (190 miles) northeast of the Mt. Newman iron ore project in the northern part of Western Australia. The first mineral claims were staked in 1972; and by mid-1975 ore reserves of 3. 8 million mt (4. 19 million st) of 9.6 g per mt (0. 28 oz per st) ore had been indicated. It is interesting to note that Newmont spent more than 10 years and A$10 million in Australia for extensive mineral exploration before finding the Telfer deposit, and then spent approximately A$3 million in exploration and feasibility engineering on Telfer. Including this A$3 million, a total of A$27 million was spent to complete construction of the mine, village, gold treatment plant and associated roads, airport, water and services. Over 50% of the capital cost is in the metallurgical facility, or approximately A$10, 000 per ton per day. All economically significant gold mineralization at Telfer occurs in a series of layered quartz-limonite reefs in which the former pyrite has been oxidized to limonite to a depth of 100 m (330 ft). The most important gold reef occurs at the base of the siltstone-shale horizon within the enclosing sandstone dome -like structure. At the Main Dome structure the dipping ore horizons will be mined to a vertical depth of about 60 m (200 ft) by open-cut methods. The waste-to-ore ratio is approximately 12:1. Eventually 44 million mt (48. 5 million st) of ore and waste will be mined. Mining of the waste is by contract; however, the ore and a thin layer of waste is company-mined. Dilution from mining the geological ore reserve is about 10%. The ore is completely oxidized and the gold occurs free within the reef, material as discrete particles of varying but mainly fine grain size. Most of the gold is "free milling"; that is, over 50% of the gold is coarse enough to be recoverable by gravity concentration. Two duplex mineral jigs receive the two cyclone underflows from the grinding circuit. The rougher jig concentrate is up-graded on a continuous strake from which the concentrate is tabled to produce a final free gold product. Jig tailings are returned to the ball mill and the concentrates are amalgamated. Gold amalgam is pressed, retorted, and melted into gold bars. The gravity gold recovery circuit is the same as was used in many of the gold mills in California in the 1930s.

Jan 1, 1981