Search Documents

By R. Schuhmann Jr., P. J. Ensio

As a first step in a study of the physical chemistry of copper-smelting slags, experimental measurements were made of the oxygen pressure of simple iron-silicate slags in equilibrium with solid iron. The experiments consisted in bubbling CO2-CO mixtures through the slags in iron crucibles and in finding the equilibrium ratios of CO2 to CO. From the data, activities and partial molal heats of solution FeO and SiO2 in the slags were calculated. THE ternary system FeO-Fe,O,-SiO, is the simplest system which can represent adequately the important chemical properties of the slags formed in matte smelting and converting. Accordingly, the experimental study of slags in this system was started as the first step in a general research program on the thermodynamics of copper smelting. A recent paper by one of the authors' outlines this general research program and shows in some detail how information on thermodynamic properties of iron-silicate slags, especially information on oxygen activities, is essential to a full understanding of the chemistry of copper smelting. The FeO-Fe,O,-SiO, system also is the basis of slags produced in other processes, such as acid steelmak-ing processes, and is important in relation to the behavior of silicious refractories. In addition, data on the physicochemical properties of iron-silicate slags should contribute to a general understanding of the nature of slags, since at present such data for all kinds of slags are relatively meager. The principal quantitative information already available on iron-silicate slags consists in Bowen and Schairer's constitution diagram for slags in equilibrium with metallic iron,' Darken and Gurry's complete and precise thermodynamic study of the Fe-0 system,",' and Darken's study of the phase equilibria in the Fe-Si-o system. From the results of this previous work, it was clear that a complete thermodynamic study of ternary iron-silicate melts was a major undertaking which would have to be broken down into parts, including the working out of the ternary equilibrium diagram as well as extensive activity measurements on slags. The experimental measurement of oxygen activity, using CO-CO, and other gas mixtures as yardsticks of oxygen activity, was the basis of Darken and Gurry's study of the Fe-0 system. From the experimental measurements of oxygen activities over a large range of temperatures and compositions, they were able to calculate the activities of other species such as Fe, FeO, Fe,O,, etc., and also the other important thermodynamic properties in the Fe-0 system. At the start of the present investigation, it appeared that the same approach would be fruitful for the study of iron-silicate melts. Also, the experimental measurement of oxygen activities seemed particularly attractive because oxygen activity itself is a quantitative measure of oxidizing or reducing power, which is an important variable in copper-smelting slags. The slag compositions in equilibrium with yFe appeared most suitable for the first investigation of this kind, for the following reasons: 1—Good constitution data2 were available. 2—An iron crucible could be used, thus affording a simple solution to the refractory problem without introducing contarnination. 3—With Fe activity fixed, at unity with respect to a standard state of solid Fe, measurements of 0 activity could be followed by simple calculations of activities of FeO and other Fe-0 complexes and of SiO,. 4—This starting point afforded several possibilities for cross-checking with previous work,

Jan 1, 1952

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

By J. N. Anderson

Developments in reverberatory furnace practice at Noranda over the period 1928 to 1953 are described. Features of interest are increasing furnace tonnage from 700 to 2000 tons per furnace day, the use of the suspended basic roof, and improvements in furnace fuel ratio. Points of comparison and contrast between Canadian and American furnace practice are given. OPERATIONS at the Noranda smelter have been described in a series of papers published between 1930 and 1945.1-4 In the present paper the development of reverberatory furnace practice over the 25 year period from the beginning of operations up to the present time will be reviewed and current furnace practice will be described in some detail. Particular attention will be given to those features which are characteristic of Canadian practice: first, the use of the suspended basic roof; second, the deliberate driving of furnaces to give tonnages in the range of 1400 to 2000 tons of solid charge per furnace day; and third, the continuous operation of furnaces at high tonnage for many years without any extended shutdown for repairs or rebuilding. Finally, points of comparison and contrast between reverberatory furnace practice in Canada and the United States will be discussed. The Noranda smelter, which started in December 1927, was built for the reduction of ore from the Horne mine where early development had shown a comparatively small tonnage of rich cop-per-gold ore of a grade and character which would require direct smelting. The smelter was designed for a capacity of 1000 tons of ore a day and originally consisted of eight roasters, two reverberatory furnaces, and two converters, together with necessary auxiliaries. The discovery of a large new body of ore in 1928 made it necessary to increase both the size and the scope of the reduction plant. A mill which was ultimately brought to a capacity of 3000 tons a day was built for concentrating low grade ore and in addition the capacity of the smelting plant had to be greatly expanded, so that for the next fifteen years every effort in the smelter was directed toward achieving maximum tonnage. Because the layout and design of the smelter made it impracticable to add a third furnace, it was necessary to increase the tonnage on the two original furnaces by improvements in furnace design and operation, roasting and converting equipment being added as required to meet the demands of increased furnace capacity. The smelter tonnage, which reached a peak in 1941, was curtailed in 1944 when it became necessary to operate on a one-furnace basis because of a reduction in the output of the Horne mine due to a shortage of labor. Two-furnace operation at a moderate tonnage was resumed in 1949. In the early years the smelter tonnage was made up almost entirely of Noranda ores and concentrates. However, since 1937 an increasing tonnage of ores and concentrates from other mines has been treated in the smelter. In recent years, with decreased production from the Horne mine, copper concentrates from several mines in the district, treated on a custom basis, have formed an important part of the smelter tonnage. A review of developments in reverberatory furnace practice at Noranda falls naturally into the following four periods: 1—1928 to 1935, the early years; 2—1935 to 1944, the period of greatest change and development; 3—1944 to 1949, one-furnace op-

Jan 1, 1955

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By D. L. Albright, R. W. Kraft

Solidification experiments were conducted with the objective of testing the theory of eutectic colony formation. Appropriate control of variables in tests on a series of high-purity aluminum-copper specimens of eutectic composition resulted in the observation of three types of eutectic microstructures, these being a unique structure consisting of lamellae essentially parallel to one another, a banded structure, and the colony structure. Lamellar faults, which are morphologically similar in many respects to edge dislocation models in crystals, produced a complex substructure in these specimens. SOLUTE rejection at the advancing solid-liquid interface of a unidirectionally solidified single-phase metal can cause the liquid immediately in front of the interface to become constitutionally super-cooled below the equilibrium liquidus temperature. Constitutional super-cooling occurs if the solidification rate, R, is too rapid, or if the thermal gradient in the liquid at the interface, G, is too low. 1 This constitutionally supercooled layer in turn stabilizes a cellular rather than a planar interface.&apos; A similar cellular interface has been observed when lamellar and other types of eutectics were unidirectionally solidified, and it has been shown that the cellular interface led to the formation of eutectic colonies.&apos; The lamellar structure is fan-shaped at the edges of colonies (which correspond to valleys or grooves in the cellular interface) because the lamellae grow normal to the local interface. One of the possible mechanisms which might cause the formation of the cellular interface, in the case of solidifying eutectic alloys, is constitutional supercooling of the liquid with respect to a third component rejected by both phases of the eutectic.3,4 On the basis of the analogy between the solidification of single-phase metals and binary eutectics, a eutectic alloy should solidify with a planar interface if the ratio of G/R is sufficiently high to compensate for any impurity which might be present and causing constitutional supercooling. The fan-like microstruc-ture of eutectic colonies should not occur under these conditions and the lamellae should be parallel to one another and to the solidification direction for extended distances. The experiments conducted in this investigation were designed to test these ideas. Following a resume of the experimental procedure, the various microstructures observed during the study are described, and their relationship to the growth conditions which produced them is discussed. EXPERIMENTAL PROCEDURE The eutectic between an aluminum solid solution and 0 phase (approximate composition CuA12) was chosen for this work for the following reasons: it was known that a lamellar structure forms, the eutectic temperature is low enough to facilitate experimental work, and the components can be procured commercially in a very pure form. High-purity copper (est. 99.999 pct Cu, obtained from National Research Corp.) and spectrographic aluminum rods, having impurities other than copper estimated to be Zn-15 ppm, Mg-10 ppm, Fe-3 ppm, Na-2 ppm, Cd-1 ppm, and Mn < 1 ppm, were melted in a stabilized zirconia crucible in a vacuum induction furnace at a pressure of 10 pof Hg. The melt was superheated to about 1000°C to assure mixing, cooled to 780°C and cast into an investment mold which yielded sixteen cylindrical specimen blanks 1/2 in. in diam and 5 1/2 in. long. The casting was allowed to solidify under vacuum. This master heat had an analysis of 32.6 wt pct Cu and 67.4 wt pct A1 by difference. The cylindrical specimen blanks were remelted and solidified unidirectionally in an apparatus illustrated schematically in Fig. 1. An RF induction coil heated

Jan 1, 1962

By C. A. Stout, S. W. Nicksic

The materials that stubilize emulsions of some Southern California crude oils were isolated from the produced crude. These substances were separated into acidic and nonionic fractions by ion exchange chromatography. Each fraction was further broken into groups of homogeneous molecular weight composition by gel permeation chromatography. Both ionic character and molecular weight of the individual fractions are reflected in the properties of the original crude oil emulsion. Specifically, the more acidic and the higher molecular weight fractions appear to be the most effective stabilizers. INTRODUCTION The treatment of oilfield emulsions is a continuing problem for the oil industry. In almost all cases, these are water-in-oil emulsions. Much more is known about the formation and stabilization of oil-in-water (O/W) emulsions than of the water-in-oil (W/O) type. To understand W/O emulsions, more information is needed on the materials responsible for their formation and stabilization. This is especially true in the case of oilfield emulsions where the stabilizing materials are complex mixtures of large asphaltene-like molecules. To study the chemical and physical properties of these emulsion stabilizers, it is necessary first to separate them from crude oil. This separation was achieved in the case of two Southern California crude oils. The materials that were isolated appear at first to be little different from an asphaltene mixture. However, if a mixture of distilled water and mineral oil containing about 1 percent of the natural emulsion stabilizers is passed through a colloid mill, the W/O emulsion formed may be stored in the laboratory for many months without any sign of breaking. This could not be done using undifferentiated asphaltenes from the same wells, indicating that there is a real difference between these materials and ordinary asphaltenes. The colloid mill used to generate the emulsion was required because tile natural emulsion stabilizers had very little effect on oil-water interfacial tension. The one characteristic — complexity of composition — that emulsion stabilizers share with asphaltenes makes virtually impossible the exact structure determination of the components of the mixture. For this reason, it was decided to investigate first the influence of molecular weight on the ability of these materials to stabilize emulsions. The emulsion stabilizers were first separated into acidic and neutral fractions according to whether or not the material was retained on a weakly basic ion exchange column. The extraction procedure was not designed to remove basic components from tile oils, and no attempt to isolate such a fraction was made. Following this separation, selected fractions were analyzed by gel permeation chromatography. Gel permeation separates according to molecular size, largely independently of chemical or polar characteristics. A heterogeneous mixture is separated into a number of fractions having much more homogeneous molecular weight distribution. A number average molecular weight of each fraction is therefore close to the true molecular weight of the principal component of that fraction. The fraction weights, expressed as weight percent of the sample, and the number average molecular weight of a representative selection of the fractions, will be referred to in this paper as the molecular weight profile of the original sample. DESCRIPTION OF GEL PERMEATION ANALYSIS The first reported gel permeation analyses were for separating partially hydrolyzed protein molecules in an aqueous system using expanded starch granules. Most of the theoretical work on gel permeation has been done by biochemists.1 This theoretical treatment is still incomplete, but the

Jan 1, 1969

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Richard W. Graeme, James J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona project, located in Hualgayoc, Cajamarca Department, Peru, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, project development occurred against the backdrop of a presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as an unprecedented demand for engineering and technical skills. Project “Lessons Learned” are discussed in the context of an evolving strategy. The Cerro Corona project forms part of a porphyry copper-gold deposit situated within the Hualgayoc Mining District in northern Peru. It is located in the highest part of the Western Cordillera of the Andes, close to the headwaters of the Atlantic Continental Basin. It lies approximately 90 km (56 miles) by road north of the Department of Cajamarca’s capital city and near the village of Hualgayoc. Access to the Cerro Corona project from Cajamarca is by two roads, one from Cajamarca to the Yanacocha Mine 45 km (28 miles), and then from Yanacocha to the village of Hualgayoc and the town of Bambamarca 45 km (28 miles).

Jan 1, 2007

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

By A. W. Popp

After forty years of exploration and development, the heavy mineral sand deposits of the Murray Basin are on the eve of substantial exploitation by Iluka Resources Limited, Southern Titanium NL and RZM/Cable/Bemax, whom plan to initiate mining and processing operations in 2005. A trial mining and processing operation was undertaken on the Wemen North strandline deposit in 2001-2003 by Murray Basin Titanium, a joint venture of Sons of Gwalia and RZM/Cable, which brought to light a number of mining and processing problems which have since been the subject of extensive studies and process development work. The mineralogy of these weathered strandline deposits is complex by industry standards due to the variety of the heavy minerals present, coatings on the mineral grains and the extensive weathering and alteration which has taken place during the past 50 million years. This paper provides an overview of the complex mineralogy that, in turn, dictates the processes that can be used to recover the valuable heavy minerals. The Murray Basin encompasses some 300,000 km2 and has been a depositional basin, often land locked, since the start of the Cenezoic Era. The economic heavy minerals include ilmenite, altered ilmenite, leucoxene of highly variable composition, rutile, and zircon. There are also other heavy minerals present such as cassiterite, chromite, and monazite in quantities that pose both problems and opportunities. The clay content and overburden thickness also play a major role in the selection of the deposits to be mined. Project Services Consultants (PSC) has undertaken the preparation of this paper as part of its ongoing participation in the mineral sands industry and in particular the project development activities in the Murray Basin region currently being undertaken by Iluka Resources. PSC has been involved with the mineral sands business for several years with senior staff having in excess of 30 years global industry experience. The company is well placed to provide a range of services to clients like Iluka Resources in the areas of project development, execution and strategic development and industry advice.

Jan 1, 2005

By Blanchard R

The discussion submitted by Drs. Stillwell and Edwards is at once helpful and gratifying to the authors. Their contribution deals with two phases of the problem-(I) an additional suggestion for the relative solubility of galena and marmatite, and (2) submission of an alternative explanation for the greater leaching of the Northern ore-body. With the first we agree in principle, and herewith present recent data which will help to substantiate the idea, though the mechanism is not believed to be as simple as indicated by Stillwell and Edwards. Concerning the second suggestion, the original explanation put forward. in the paper is held to fit the facts more closely.In view of the influence, as shown by Garrells&apos; paper,in which the presence of Cl&apos; ion may have upon the relative solubilities of lead and zinc, it is perhaps worth noting that Broken Hill mine water carries a higher content of Cl&apos; than has been reported from many of the other lead-zinc districts.Since our paper was published, an analysis of water issuing from the newly-opened Northern ore-body on the 2,600-ft. level has been made (12/1/43). It is compared with that quoted in the original paper as follows:

Jan 1, 1943

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007