Search Documents

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

Masjid-i-Su1aiman.—There have been no new developments in the Masjid-i-Sulaiman oil fields during the year 1938. In spite of the age of this field, the fall in dome pressure shows no appreciable variation from the low rate of about 0.3 lb. per sq. in. per million tons net production. Drilling has been limited to deepening old wells and to new wells required for maintenance of production and general reservoir control. The rate of offtake has been reduced over the past few years, partly because of depletion of the oil column, and it is expected that future offtake from the Masjid-i-Sulaiman field will be stabilized for some years at around the present figure of 3,000,000 tons per annum. Haft Ke1.—An exploratory well to test deeper formations in the Haft Kel field has proved the existence of productive conditions in the Eocene, which underlies the Asmari limestone (the main producing horizon). Drilling to the northwest in the white-oil springs area has revealed the presence of a separate structure with productive potentialities. One well with a satisfactory production rate has been completed. Offtake from the Haft Kel field has steadily increased since it first came on to production in 1929. Naft-i-Shah.—Production from this field has continued to supply market requirements in northwest Iran. The policy of returning surplus products to the reservoir, which was adopted at the beginning of 1936, has been continued.

Jan 1, 1939

By P. Katsabanis

Researchers in the field of blasting have been trying to develop ways of predicting fragmentation in the last few decades. The Kuznetsov equation estimates the average fragment size, XJ~, based on explosive energy and powder factors. Cunningham calculates the uniformity of a fragment size distribution using drilling accuracy, blast geometry and a rock factor A associated with a “blastability index”, which can be estimated from the jointing, density and hardness of the blasted rock mass. Knowing the mean size and the uniformity index, a Rosin-Rammler distribution equation can then be derived for calculating the fragment size distribution in a blasted muckpile. Analysis of existing data has revealed serious discrepancies between actual and calculated uniformity indices. The current integrated approach combines the Kuznetsov or similar equation and a comminution concept like the Bond Index equation to enable the estimation of both the 50% and SOoh passing sizes (X& and X& ). By substituting these two passing sizes into the Rosin-Rammler equation, the characteristic size (Xc ) and the uniformity index (n) can be obtained to allow the calculation of various fragment sizes in a given blast. The effectiveness of this new fragmentation prediction approach has been tested using sieved data from small-scale bench blasts, available in the literature. This paper will cover all tested results and a discussion on the discrepancy between measurement and prediction due to possible energy loss during blasting.

Jan 1, 2001

By S. H. Amini

The effects of CaF2 and ilmenite on dissolution rate and diffusivity of CaO in calcium alumino-silicate based slag in a temperature range of 1500 ? 1600 ºC were studied by using the rotating disk/cylinder technique. The effect of rotation speed on the rate of dissolution in the base slag indicated that mass transfer in liquid slag played a significant role in controlling the dissolution. At a constant rotation speed, the effect of 5 wt% addition of fluxes tothe slag on the dissolution rate was investigated at various temperatures. While CaF2 had the highest effect, addition of ilmenite increased the rate of dissolution significantly. The diffusivity of lime in these slags was quantified using the dimensionless mass transfer correlations for rotating disk/cylinder in the melt. The diffusivity values were deduced using the data on dissolution rate and solubility of lime in the slags. The measured diffusivity in base slag at 1500 C was found to be about 1.32 10-5 cm2/s and increased to 3.07 10-5 cm2/s at 1600 °C. Addition of 5wt% CaF2 increased the diffusivity by a factor of 3 to 5, while 5wt% ilmenite increased the diffusivity by a factor of 2 to 3 in the temperature range of 1500 to 1600 ºC. The two examined fluxes reduced the activation energy of diffusion.

Jan 1, 2006

By D. G. Krige

Using a very large number of chip-sample values from a mined-out area of the Hartebeestfontein mine and accepting these as equivalent to borehole values (also areas of 1 km by 1 km as equivalent to 'mines'), the authors apply a series of borehole-valuation procedures to these 'mines', Large undeveloped sections of existing mines are also regarded as the equivalent of such 'mines'. These procedures start with the orthodox arithmetic mean and then introduce additional information in the form of the Iog normal frequency distribution model for Sichel's 't' estimator. Knowledge of the average log-variance within mines leads to the tH estimator. The mean grade of the 'family' of mines to which a new mine belongs is then introduced via regression or elementary kriging. Next, further information on the macro spatial structure of the grade is used, together with the grades of adjacent existing mines in ordinary and simple macro-kriging procedures; finally, via the distribution model, the grade is seen as a function of the logs of the grades and their variances. These are introduced as spatial variables, and both are estimated by macro-Iog normal ordinary and simple kriging procedures with grades and variances from adjacent mines'. Comparisons are also made between macro-kriging on lognormal transformed values versus untransformed values. Conclusions are drawn on the relative importance of the various items of additional information used, on the procedures followed, and on the significance of the advantages gained

Jan 1, 1992

FRANCIS B. SILSBE,* Washington, D. C. (written discussion?). ?This paper is an interesting example of the -solution by the methods of metallography of what seemed at first a purely chemical problem. The authors have shown: in detail, how the well-known corrosion of spark-plug terminals is due to the dropping out of the individual crystals of the metal as it becomes surrounded by an oxide film. This corrosion is usually quite slow but in special cases may become a serious factor in limiting the life of spark plugs. There still remains the problem for the metallurgist to produce a material that will be entirely free from, this trouble. One of the most startling results of the work is. the demonstration that it affords of the deleterious effect of a mechanical stress continuously applied to material that is at the same time subject to adverse chemical or thermal conditions. The particular style of spark plug shown in the illustration, and in which serious trouble was caused by this corrosion, has the side terminals fastened at both ends and the method of assem-bling is such that a considerable initial tension is applied to the wire. It is without doubt this superimposed tension that causes the inter-crystal-line network to line up, as it were, into a few continuous and deeply penetrating transverse fissures instead of forming a great number of shallow surface cracks. This result is clearly shown both in the case of

Jan 11, 1919

By Behram H. Wadia, Robert S. Lehto

A new metallurgical treatment for capturing as much of the values as possible from zinc refinery feed has been devised by personnel in Cerro de Pasco's Peruvian operation at La Oroya. Results from a pilot test illustrate that 50 metric tons of throughput can be maintained whereby substantially all the silver and copper report in the sponge iron while zinc and lead with indium and cadmium volatilize in the fume. This new technique named the Zileret (zinc leach residue treatment) process complements the electrolytic system used in the refinery so that all values in a zinc concentrate are economically recovered. In the system, dried zinc leach residue is pelletized with soluble zinc sulfate which already exists in the leach residue and a finely divided reducing agent such as anthracite coal. Upon heat addition, the loose anthracite in the charge maintains a reducing atmosphere while the free space above the charge has an oxidizing nature. When the charge reaches the reaction zone at about 1100°C, metals such as zinc, lead, cadmium and indium volatilize from the pellets, are oxidized in the upper kiln atmosphere, and are then carried in suspension as an oxide fume to the cooler and baghouse. The copper and silver content in their reduced forms, along with the iron, discharge from the kiln as a calcined product which is then cooled to below 130°C before being exposed to the air.

Jan 9, 1969

No greater opportunity for public service has ever been presented to the engineers of the United States, as a class, than the campaign to make thrift a permanent American habit, conducted through the Savings Division off the Treasury Department. The engineer owes a duty to his community, to his country, by reason of the very fact that he is an engineer. By reason of his position and influence, his education and experience, he owes to his country the duty of public service. The public understands that the opportunities of the engineer have allowed him to equip himself to handle logically and properly questions affecting the public. He has been trained to maintain a constructive viewpoint. His work is constructive and he builds for the future. The qualities that the public deems necessary for public service have been bred in him. The time has gone by when the professional man can perform his whole duty to himself and his community by shrouding himself and his calling in mystery and locking himself away from the public in office or laboratory. The duty of public service is calling for every man whose training has fitted him to perform that service. The engineers of the country have demonstrated their capacity and their willingness for public service. Throughout the war period they, have been found in every branch of governmental and. civilian activity which could contribute to national success, doing their share to promote national efficiency. Their duties are not over.

Jan 7, 1919

By Maynard Stenberg

Judging from the progress made in August 1989, drilling and raise boring of a 400-m (1312-ft) pilot hole at the Elura mine of Pasminco Ltd. in Southeastern Australia, an observer would never guess that the project had been delayed nearly a year. Moreover, two pilot holes had been abandoned in previous attempts. The challenge was to drill a 93-mm (3.66-in.) H size exploration hole between Elura's 400- and 800-m (1312and 2624-ft) levels. The hole needed to be kept within a 300-mm-diam (12-in.diam) target cylinder over the 400 m (1312 ft) distance. The deviation restriction of the initial core hole was necessary to precision ream a pilot hole to 330 mm (13 in.) and then raise bore a 6-m-diam (20-ft-diam) shaft, planned as the primary men and materials access between the two levels. Core was not really necessary to gain an accurate geological picture of the steeply dipping formation. Rather, the core barrel was used because it tended to drill a straighter hole. Using rock bits in the steeply dipping formation would have simply aggravated the problem of deviation. The core barrel and diamond bit optimized the probability of a straighter hole. However, on the first two attempts to drill the pilot hole, the bit was out of the 300-mm (12-in.) target cylinder within the first 50 to 60 m (164 to 197 ft), and the holes were abandoned.

Jan 1, 1990

Masjid-i-Su1aiman.—There have been no new developments in the Masjid-i-Sulaiman oil fields during the year 1938. In spite of the age of this field, the fall in dome pressure shows no appreciable variation from the low rate of about 0.3 lb. per sq. in. per million tons net production. Drilling has been limited to deepening old wells and to new wells required for maintenance of production and general reservoir control. The rate of offtake has been reduced over the past few years, partly because of depletion of the oil column, and it is expected that future offtake from the Masjid-i-Sulaiman field will be stabilized for some years at around the present figure of 3,000,000 tons per annum. Haft Ke1.—An exploratory well to test deeper formations in the Haft Kel field has proved the existence of productive conditions in the Eocene, which underlies the Asmari limestone (the main producing horizon). Drilling to the northwest in the white-oil springs area has revealed the presence of a separate structure with productive potentialities. One well with a satisfactory production rate has been completed. Offtake from the Haft Kel field has steadily increased since it first came on to production in 1929. Naft-i-Shah.—Production from this field has continued to supply market requirements in northwest Iran. The policy of returning surplus products to the reservoir, which was adopted at the beginning of 1936, has been continued.

Jan 1, 1939

By William H. Spice

No devclopment of major importance has been made in the south central fault-line district of Texas during 1939. Four new fields have been discovcred, all of which appear to be of minor importance, with small wells in the Navarro sand, the Taylor marl or the Austin chalk. Drilling along the fault line has not developed any new prospects in the Edwards lime, the most prolific producing horizon of the district. At the close of the year, a few deep tests for lower producing horizons have been projected and should prove to be of interest, and plans are under way for further development of the Pearsall field, which has been under the control of a single company until recently. Production from the 46 producing fields was maintained at 8,460,000 bbl. for the year, a decrease of approximately 400,000 bbl. under 1938. This decrease is due in part to natural decline of production and in part to decreased allowed production. Approximately 55 producing wells were completed on proven acreage in the Darst Creek and Salt Flat fields. No new lease plays were made during the year, although approximately the same amount of land, 600,000 acres, remained under lease during the year. Some geophysical operations of various types were carried on along the fault-line area itself and also in the Edwards plateau and in the area south and southeast of the main fault line.

Jan 1, 1940

By William H. Spice

No devclopment of major importance has been made in the south central fault-line district of Texas during 1939. Four new fields have been discovcred, all of which appear to be of minor importance, with small wells in the Navarro sand, the Taylor marl or the Austin chalk. Drilling along the fault line has not developed any new prospects in the Edwards lime, the most prolific producing horizon of the district. At the close of the year, a few deep tests for lower producing horizons have been projected and should prove to be of interest, and plans are under way for further development of the Pearsall field, which has been under the control of a single company until recently. Production from the 46 producing fields was maintained at 8,460,000 bbl. for the year, a decrease of approximately 400,000 bbl. under 1938. This decrease is due in part to natural decline of production and in part to decreased allowed production. Approximately 55 producing wells were completed on proven acreage in the Darst Creek and Salt Flat fields. No new lease plays were made during the year, although approximately the same amount of land, 600,000 acres, remained under lease during the year. Some geophysical operations of various types were carried on along the fault-line area itself and also in the Edwards plateau and in the area south and southeast of the main fault line.

Jan 1, 1940

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

By Rolley P

In the course of reviewing grade control practices at the Marvel Loch gold mine in Western Australia in 1992, FSSI Consultants developed and implemented a novel approach to ore selection using a method to maximise financial return (the MP method*). The approach was based on improved grade control sampling and an ore selection method which directly incorporates both a measure of the uncertainty in knowing the true grade of selection units in the definition of ore, as well as the operating cost and revenue parameters of the mining operation. During the past four years, FSSI Consultants have evaluated and refined the use of this approach and have implemented customised variations of the MP method at seven gold mines and a gold-copper mine in Australia. The previous methods of ore selection at most of these operations were based mainly on polygonal - sectional methods of grade estimation. At all of the sites where grade control optimisation has been given a fair trial over several months of production, the use of the MP method has been consistently rewarding to the mining operations. The benefits include increased run of mine ore stockpiles and low-grade stockpiles and decreased fluctuation in the production grade. Most operations have also benefited from a consistent ability to improve production grade through high-grading of the increased ore production. The increase in ore production has the logical benefit of reducing stripping ratios, increasing mine profitability and mine life.

Jan 1, 1997

By Jacob Feld

Introduction The best way to eliminate the possibility of rapid excavation in tunnel work is to start an argument between Owner Engineer and Contractor. And arguments are readily started when work is progressed without a frank open agreement on the rules of the game. Fifty years ago a tunnel contractor took a job to excavate and line a tunnel, providing all labor and materials under the guidance and continuous instruction of the Engineer who provided all survey work, checked each new heading and set the lines for the next round of drill holes, usually designed and ordered protective measures, kept record of progress and controlled payment for the work. In my first job in a tunnel, muck cars were loaded by hand and hauled by donkeys. Progress was, at today's criteria, not rapid. The Contractor or in the case of a large concern, his executive field representative was always at the site, knew most of his men by name, and there was a mutual feeling of respect between him and the Engineer in charge of the work. Misunderstandings were cleared up when they came up, expeditiously and fairly, even though satisfaction was not always expressed. The Owner came for the ground breaking and usually for the holing through shot. The Owner had full reliance on the Engineer's ability and integrity. The Engineer recognized the Contractor's expertise in being able to man the job and produce results.

Jan 1, 1974

THE papers by G. F. Loughlin and I. A. Ettlinger discussed the distribution of formations and ore-bodies in two of the main mining districts of the Southwest. The convergence of the deeper orebodies at Cripple Creek points to their common hypogene ori-gin, as do the occurrences of the copper ores of, central Arizona. E. L. Bruce described the areas in southwestern On-tario around Red Lake and Woman Lake, another prom-ising gold district. Of special interest was a series of lantern slides showing the use of power-driven boats and of hydroplanes as means of transportation. Within a few years, no doubt; such devices will revolutionize the mining industry and reconnaissance mapping in these relatively inaccessible areas. Much interest was evinced in the paper by J. W. Finch on "Sedimentary Metalliferous Deposits of the Red Beds." It was written as a caution to people at-tempting to mine these deposits. The discussion of the chemical equations presented in the paper brought out the fact that a large amount of study of such ores is necessary before we shall be able to write equations to explain their formation. Especially pertinent were the discussions by David White as to the relation of decay-ing plant tissue to metalliferous deposits and the color of sediments; also the point brought out by T. S. Lover-ing that chemical compounds produced by bacteria may greatly affect the deposition and reorganization of sedi-mentary metalliferous deposits.

Jan 3, 1928

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

Discussion of the paper of Herbert F.. Miller, Jr., presented at the New York meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 409 to 413. HENRY D. HIBBARD, Plainfield, N. J.:-Looking at the illustrations, it seems to me that a furnace made with the width of port that is shown here would not be a good working furnace. The economy of brick and gas might be all right, but I do not think it would melt the steel properly. I should say that the flame would not spread out suitably to fill the whole hearth of the furnace, and there would be undue waste, and it seems to me that it would be an undesirable furnace to adopt. The question as to whether a producer-gas flame would lie down in the furnace, hugging the bottom better than the natural-gas flame, is settled, not so much by the specific gravity of the gases themselves, as by the relative temperatures at which they enter the laboratory of the furnace. We know in that case that producer gas would be lighter than a natural gas which had not been run through a regenerator and expanded four or five volumes in consequence. I would like to hear what Mr. Miller has to say about the action of the flame spreading properly over the charge to give good metallurgical results in the form of furnace which he presents.

Jan 5, 1913

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957