Search Documents

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By C. M. Loeb, A. M. Gaudin, J. H. Brown

THE object of most size reduction operations in the mineral industry is to liberate the grains of valuable minerals in the ore from those of the gangue. This is usually accomplished by crushing and grinding the entire mass of ore until there is only a small probability that any single particle contains more than one mineral. During this size reduction only limited control exists over size or composition of the particles exposed to the breaking action, and there is no control over the paths followed by cracks generated during the operation. This lack of control usually results in overgrinding and in production of large quantities of very fine material. The first detriment, overgrinding, is costly in itself, but when combined with the second factor it is doubly so. Not only is the fracture of a free particle unnecessary-the fracture of these particles may also make subsequent separation operations difficult, inefficient, and wasteful. It has been pointed out' that if the object of size reduction is to liberate the valuable mineral component of the ore then, ideally, fracture should follow intergranular paths to the exclusion of trans- granular ones. This would result in liberation of the valuable minerals with as little size reduction as possible. This ideal comminution operation is referred to as intergranular comminution, and it was the object of the investigation to determine the extent to which it could be developed by heat treatments.

Jan 4, 1958

By Allen Johnson

WITH a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Labo-ratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. STOKERS INVESTIGATED One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-Stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.-The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plungers, or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal. through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the ,general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1935

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By G. Blight

As part of an investigation of possible water-saving measures at Anglo American Platinum's Mogalakwena Mine in Limpopo, South Africa, a study was made of conditions on the wet beaches of two adjacent tailings dams, each serving a separate plant on the mine. For one of the dams, a special catamaran was designed and constructed to enable the full length of wet beaches to be accessed and sampled immediately after a layer of tailings had been deposited. For the other dam, the wet beach was accessed using conveyor belting and scaffold planks. The length of the beaches was 400 m on the first dam, and 200 m on the second, and each was sampled at 50 m intervals. The parameters reported in this paper, for both beaches, are: > Water content profiles along each beach from the surface to as deep as 2.5 m, at times ranging from 12 hours to 6 weeks from the end of deposition > Particle size distributions at the surface, down the full length of the beaches > Measurements of feed relative density, tonnage and volume, decant and drain flow volumes, as well as rainfall and evaporation for both dams. The surface water contents shortly after deposition have been used to establish the relative density of the settled, decanted tailings and its variation down the beach. This data, combined with the decant and drainage flows, is used to establish the calculated and actual water recoveries from both dams.

Jan 1, 2012

By A. W. Khair

This paper presents an analysis of surface subsidence characteristics in room and pillar mining using physical models and laser holographic interferometry (holometry). The analysis included the effect of various geometric parameters and different overburden materials (sand and gelatin) and resulted in the formulation of a more realistic model material for laboratory simulation of typical geologic overburden. Previous work using this technique involved the use of sand to model over- burden and detailed results are presented elsewhere (1). The main emphasis of this work was to develop a gelatin based mixture which would provide a better model. Initial work during the development of this model included testing various ingredients and monitoring the time dependent characteristics of the model, such as the surface penetration resistance. This value indicated changing deformability/ridgidity of the model with time. Once several models had been developed, holometry techniques were applied. Initial tests showed that the stiffness of gelatin created a bridging effect over the mine models, thus restricting deformation. At this point, a 0.5 inch (1.27 cm.) layer of sand was placed directly over the mine model with the gelatin mixture on top. The approach was to model different zones of overburden movement that exist as an extraction occurs (2). The sand would represent the caved and fractured zones which occur above the excavated area. The gelatin models the continuously deformed zone which occurs between the fractured zone and the surface. Holometry techniques applied to this model yielded successful results.

Jan 1, 1986

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By Dale T. Peters

In the United States, the United Kingdom and numerous other countries, copper has long been the plumbing material of choice. This has been the case since the late 1920s in the United States and since World War II in the United Kingdom. However, in recent years the plumbing tube market has caught the eye of the chemical industry, and several plastic resins have been introduced to the marketplace as substitutes for copper in household plumbing systems. One of these, polybutylene tube, had so many failures in the United States that a class action law suit was filed, and the manufactures of this product were forced to create a trust fund of nearly one billion dollars to repair damages caused by their product. Chlorinated polyvinylchloride (CPVC), in rigid pipe form, on the other hand, has been mechanically acceptable albeit its recent introduction precludes the test of time enjoyed by copper tube in this application. This paper reviews the State of California's portrayal of copper's environmental effects and will be largely based on the data and information assembled by the Copper Development Association Inc. in its presentation to the State of California in August, 1998 in response to the State's Draft Environmental Impact Report for Chlorinated Polyvinyl Chloride (CVPC) Pipe for Use for Potable Water Piping in Residential Buildings. The paper is intended for use as a model for the use of other copper organizations and individuals in responding to similar situations.

Jan 1, 1999

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By V. Annamalai, J. B. Hiskey

Abstract-The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol-1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol-1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 6, 1978

By V. Annamalai, J. B. Hiskey

The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol- 1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol- 1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 1, 1979

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By Andrews Allen

THE large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc. have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired hoisting tonnage can be secured and, since only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining.

Jan 2, 1921

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By Mingju Liu

The coal and gas outburst accident on May 20, 2007 at Sihe Coal Mine is unique in that there was no or very little soft coal in the coal seam and that the coal strength was very high. The outburst also showed that there was a very high gas content of 20-30 m3/t in the coal seam nearby the outburst site. Based on the field test and observations, together with laboratory experiments, detailed analysis was conducted on the controlling factors of coal and gas outburst potential at Sihe Coal Mine. Stress data available from Sihe Coal Mine, northern China, and other parts of the world, were also taken into account to facilitate the analysis. The results shows that the stress level was not abnormal compared to other coal fields in China prone to outbursts, and that gas contained in the coal seam was the main factor that triggered the outburst. All these factors were essentially controlled by the tectonic evolution features in Qinshui Coal Basin, to the Southeast of which Sihe coal field is located. Based on the analysis, assessment of coal seam outburst potential was carried out by measurements of coal seam gas contents, observation, and detection of soft coal layers in the coal seam. The results show that outbursts are limited to only a small part of the whole coal seam and that the eastern part of coal field is not prone to outbursts.

Jan 1, 2009

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970