Search Documents

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By E. P. Burtchaell

A method is presented for evaluating the effect of gravity drive upon the reservoir performance of a high relief pool. Conventional forms of reservoir analysis do not consider the alterations in the basic material balance data caused by gravity segregation of reservoir fluids. A procedure is outlined for structurally weighting physical and chemical data for use in the material balance equation. It is demonstrated how actual pool performance data can be utilized to evaluate the future reservoir performance of a gravity drive pool. INTRODUCTION Conventional reservoir engineering. procedure is inadequate for the analysis of an oil pool which has considerable structural relief, steep dips, and good permeability development. In, pools of this type, gravity drainage has an important part in the movement of oil to the wells and the effects of gravity on the overall pool performance should be included in any analysis of reservoir behavior. Many engineers have the opinion that the force of gravity in the movement of oil is not important until the later life of a pool.' Probably the basis for this belief is that gravitational effects may not be readily discernible until a pool is nearing depletion. This would be especially true for pools not having a high degree of structural relief and permeability development. Actually the effects of gravitational forces are at a maximum when the pool pressure is high, for during this period the hydrostatic head of the oil column is at a maximum and the viscosity of the oil is at a minimum. Oil recoveries from pools having favorable gravity drive characteristics may equal or even exceed recoveries which might be expected from water displacement. Field evidence indicates that in some reservoirs gravity drive has resulted in recoveries greater than that which could have been expected from gas expansion or water drive.'.3 Unfortunately, the possible effects of gravity drive on pool performance have been underestimated and other reasons have been sought to explain the high recoveries obtained. There are unquestionably many reservoirs to which the principles of gravity drainage can be effectively applied. It is the purpose of this paper to illustrate one method whereby gravity drive is included in the reservoir analysis of an oil pool. A hypothetical pool, typical of many California reservoirs, is used as an example. As used in this paper, "gravity drive" is defined as the overall effect of gravitational influences on the recovery of petroleum from the reservoir; "gravitational segregation" as the gravity separation of oil and gas within the reservoir; and "gravity drainage" as the downward movement of oil as caused by the force of gravity. SAND VOLUME DATA Fig. 1 presents a structural contour map of the pool under study. Maximum closure is 1950 feet with dips on the south flank approaching 45". The original gas-oil interface was set at -5200 feet. Average thickness of the producing sand was 200 feet. For use in subsequent calculations ill this paper, the pool was subdivided into 100-foot vertical increments and the sand-volume content of each increment was obtained. If the gross sand thickness is small, under 100 feet, the sand-volume content can be obtained by superimposing an isopachous map upon a structural contour map and planimetering the average thickness of each 100-foot increment. For sand thicknesses over 100 feet, one approacli would be to construct a sufficient number of cross-sections of the pool from which the weighted sand-volume of each 100-foot increment could be obtained. Variations in the sand body with depth, as determined by core data, can also be included in the above process. Table I presents a summary of sand-volume calculations, core data, and the original distribution of reservoir hydrocarbons in the pool. Fig. 2 illustrates the structural distribution of the sand-volume content. A total of 171,398 acre-feet is contained within the productive limits of the pool. Assuming an average porosity of 25% and an interstitial water content of 20%, the original hydrocarbon content was computed to be 227,075,000 barrels. DEPTH-PRESSURE DATA The determination of the initial vertical pressure arrangement in the pool is necessary for PVT and material balance calculations. Whenever sufficient data are available, a plot of pressure versus subsea depth of measurement should be made. From this plot a representative fluid pressure gradient can be established. Lacking sufficient initial pressure data, an initial pressure gradient may he estimated or calculated from avail-

Jan 1, 1949

By E. P. Burtchaell

A method is presented for evaluating the effect of gravity drive upon the reservoir performance of a high relief pool. Conventional forms of reservoir analysis do not consider the alterations in the basic material balance data caused by gravity segregation of reservoir fluids. A procedure is outlined for structurally weighting physical and chemical data for use in the material balance equation. It is demonstrated how actual pool performance data can be utilized to evaluate the future reservoir performance of a gravity drive pool. INTRODUCTION Conventional reservoir engineering. procedure is inadequate for the analysis of an oil pool which has considerable structural relief, steep dips, and good permeability development. In, pools of this type, gravity drainage has an important part in the movement of oil to the wells and the effects of gravity on the overall pool performance should be included in any analysis of reservoir behavior. Many engineers have the opinion that the force of gravity in the movement of oil is not important until the later life of a pool.' Probably the basis for this belief is that gravitational effects may not be readily discernible until a pool is nearing depletion. This would be especially true for pools not having a high degree of structural relief and permeability development. Actually the effects of gravitational forces are at a maximum when the pool pressure is high, for during this period the hydrostatic head of the oil column is at a maximum and the viscosity of the oil is at a minimum. Oil recoveries from pools having favorable gravity drive characteristics may equal or even exceed recoveries which might be expected from water displacement. Field evidence indicates that in some reservoirs gravity drive has resulted in recoveries greater than that which could have been expected from gas expansion or water drive.'.3 Unfortunately, the possible effects of gravity drive on pool performance have been underestimated and other reasons have been sought to explain the high recoveries obtained. There are unquestionably many reservoirs to which the principles of gravity drainage can be effectively applied. It is the purpose of this paper to illustrate one method whereby gravity drive is included in the reservoir analysis of an oil pool. A hypothetical pool, typical of many California reservoirs, is used as an example. As used in this paper, "gravity drive" is defined as the overall effect of gravitational influences on the recovery of petroleum from the reservoir; "gravitational segregation" as the gravity separation of oil and gas within the reservoir; and "gravity drainage" as the downward movement of oil as caused by the force of gravity. SAND VOLUME DATA Fig. 1 presents a structural contour map of the pool under study. Maximum closure is 1950 feet with dips on the south flank approaching 45". The original gas-oil interface was set at -5200 feet. Average thickness of the producing sand was 200 feet. For use in subsequent calculations ill this paper, the pool was subdivided into 100-foot vertical increments and the sand-volume content of each increment was obtained. If the gross sand thickness is small, under 100 feet, the sand-volume content can be obtained by superimposing an isopachous map upon a structural contour map and planimetering the average thickness of each 100-foot increment. For sand thicknesses over 100 feet, one approacli would be to construct a sufficient number of cross-sections of the pool from which the weighted sand-volume of each 100-foot increment could be obtained. Variations in the sand body with depth, as determined by core data, can also be included in the above process. Table I presents a summary of sand-volume calculations, core data, and the original distribution of reservoir hydrocarbons in the pool. Fig. 2 illustrates the structural distribution of the sand-volume content. A total of 171,398 acre-feet is contained within the productive limits of the pool. Assuming an average porosity of 25% and an interstitial water content of 20%, the original hydrocarbon content was computed to be 227,075,000 barrels. DEPTH-PRESSURE DATA The determination of the initial vertical pressure arrangement in the pool is necessary for PVT and material balance calculations. Whenever sufficient data are available, a plot of pressure versus subsea depth of measurement should be made. From this plot a representative fluid pressure gradient can be established. Lacking sufficient initial pressure data, an initial pressure gradient may he estimated or calculated from avail-

Jan 1, 1949

By A. K. Csazar, L. W. Holm

This paper describes our investigation of a post-water-flood, oil recovery process which consists of injecting a slug of propane followed by water. Also described are the results obtained by applying a modification of the process in which gas was injected ahead of the water. Under the conditions of the latter experiments, misci-bility was not achieved between the propane and gas. Preliminary experiments or) uniform, watered-out sandstone cores showed that an oil bank could be formed and produced by applying this recovery process. However, since reservoirs are not uniform in structure, the process also was applied to porous media containing irregular porosity and to stratified sand systems. As a supplenzerrt to the experinlental work, a mathernatical procedure was developed for calculating the performance of the recovery process in a bounded, layered, porous system with crossflow between layers. As a specific example, the method was applied to predict the perforrnance of the recovery process in a 6-ft long, two-layer, stratified, unconsolidated sand model for comparison with experinlental data. The calculations were programed for the ZBM 704 computer. The equations and calcula-tional procedure presented can be extended to systems containing any number of randomly distributed permeability variations or any number of parallel layers. INTRODUCTION The problem of recovering the oil that remains in a reservoir which has been waterflooded is receiving considerable attention now as an increasing number of water floods reach an economic limit. A large number of the waterflood projects are in shallow reservoirs which are at pressures below 1,000 psi. It has been demonstrated in the laboratory that post-waterflood oil can be recover-ered by miscible displacement, but the LPG-gas, miscible flood and the enriched gas drive cannot be applied effectively at pressures below 1,000 psi. Only a few reports have appeared in the literature2-4 on low pressure, partially miscible recovery methods. However, it is possible to use LPG in a partially miscible displacement process in a reservoir where pressures of 200 to 1,000 psi can be achieved. Under these Pressures and at normal reservoir temperatures, propane is miscible with the oil; but, of course, gas or water used to drive the propane slug would not be miscible with the propane. Because of the lack of complete miscibility, it has generally been concluded that excessive amounts of propane would be required to recover oil and that such a recovery method would not be economical; however, we have found that under conditions present in certain reservoirs, an imrniscible recovery process can be applied effectively. The oil saturation in reservoirs at the economic limit of waterflood projects is usually in the range of 20 to 35 per cent of the pore space." A certain portion of this oil is left trapped by water in various size pores of the rock, but a good part of this so-called "residual" oil can be present in the less permeable lenses or layers of the reservoir rock which were by-passed to some degree by the water. The oil in these permeability traps can be produced only if favorable pressure gradients are formed in the reservoirs between adjacent zones of high and low permeabilities. A low viscosity liquid, miscible with the oil in place, which is driven by water through a stratified or heterogeneous porous system can aid in the development of these favorable pressure gradients. The oil that is released thereby from the permeability traps can be recovered by the subsequent water flood. Studies were made to determine how much oil could be recovered from homogeneous and stratified cores and models, which had been water flooded, by injecting a slug of propane and driving it with water. The effect of injecting a slug of gas ahead of the water was also determined. Most of the work described herein was done with the propane-water combination; unless otherwise specified, no gas was injected. The principal objectives of the investigation were to determine (1) if an oil bank could be formed and (2) what ratio of oil recovered to propane injected would be obtained. A further objective was to develop a method for calculating fluid-flow performance in stratified systems which would account for fluid transfer between zones in hydrodynamic communication but of different permeabilities. THEORETICAL ANALYSIS In a theoretical study of the recovery process, analytical expressions were derived to calculate the pressure distribution, the fluid flux in longitudinal (parallel to layers) and transversal (across the layers) directions, and the fluid distribution at any point in the system. The equations were developed for a two-layer porous system in which it was assumed that the fluids in the system were incompressible and that capillary and gravity effects were

By Forrest V. Williams

The dislocatiorl and stacking-fault structuve of epitaxial GaAs1-,PX lms been examined by chemical etching. The layers were groun in the (100) direction and etch Pils were developed on (111} planes which nad been lapped and polished on the epiLaxia1 layevs. Tile effecL of the jollolcing cariables on the quality of the epilaxial layers has been examined: doping leuel, grouth rate, and composition. High stacking-faullL densilies weve found in the GuAsi_xpx layers. These are not observed in heavily dolled epitaxial layers tzar in layers with low phosphorus compositions. The dislocatiorz density in GuAsi-x px was highest at the sub-stvate- epilaxia1 layer interface. Composilion changes introduced dislocations in the epitaxial layers. ManY semiconductor p-n junction lasers of Group TIT-Group V compounds and their alloys have been reported in the past several years. Laser action at visible wavelengths in GaAsl-x,Px was first reported by Holonyak and Bevacqua. GaAs, a direct transition semiconductor which lases, and Gap, an indirect transition semiconductor which does not lase, form a continuous series of solid solutions.2 Laser junctions can be fabricated in GaAsl-xPx crystals with phosphorus compositions up to about 40 mol pct. In addition to the production of coherent radiation in these crystals, the efficient recombination radiation of p-n junctions in this material has equally important potential in the development of low-power semiconductor lamps. To achieve a high conversion efficiency of electrical to optical energy in p-n junctions in this material, the relation of physical properties of the crystal to luminescence efficiency must be better understood. Although the electrical, optical, and device properties of GaAsl -xPx junction lasers are understandably of considerable interest, the work to date indicates that the more serious problems are the chemical and metallurgical difficulties encountered in the growth of this material.3 In addition to the problems of chemical purity, crystal imperfections, such as dislocations and stacking faults, can be expected to affect both the efficiency of the radiative recombination process and the perfection of the p-n junction.3 The last requirement, i.c., that of the perfection of the p-n junction, is a particularly troublesome one in the fabrication of laser diodes. To obtain good laser diodes, the p-n junction must be flat, which permits the radiation to be reflected from the resonant cavity boundaries. Junction planarity is extremely sensitive to the crystal perfection of the semiconductor material. Also, it is known that at high dislocation densities (-105 per sq cm) it has not been possible to build laser junctions in GaAsl-xPx . Few studies have been reported on the crystal defect structure of GaAsl-,P,. The first serious study seems to be that of Wolfe, Nuese, and Holonyak,3 who examined the dislocation structure of monocrystalline bulk (nonepitaxial) material grown by halogen vapor transport. In this paper are reported some observations on the dislocation and stacking-fault structure of GaAsl_,P, crystals grown by a vapor transport process on substrates of GaAs. EXPERIMENTAL Crystal Growth. The GaAsl-xPx crystals were grown in an open-tube flow system, using two sets of reagents. GaAs, Pr(red), and HC1 were employed in one method. The transport reaction is =950JC GaAs+HC1 = GaCl +1/4As4 +1/2H2 and the deposition reaction is 2GaAs1-xPx +GaCl3 Composition control is obtained by the flow rate of the HC1 and the vapor pressure of the P4, which is maintained in a separately controlled furnace. The second method has been described by Ruehr-wein4 and utilizes gallium, AsH3, PH3, and HC1. The same transport and deposition reactions as above are involved. Composition control is obtained solely by the flow rates of the three gases involved. All of the crystals were grown on chemically polished GaAs substrates oriented on the (100) plane. The thicknesses of the epitaxial layers were typically 100 to 300p. Revealing of Dislocations. Dislocations were re-vealed on both the( 111 ) and { l l l }b faces by chemical etching. The specimen to be examined was mounted at 54.7 deg, lapped on glass with 3-p alumina, polished on cloth with 3-p diamond paste, and, to remove work damage, chemically polished at room temperature for

Jan 1, 1968

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20'- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes'5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1'8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.' Esin and his coworkers5'10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,'~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,'~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "'~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By R. H. Jacoby, V. J. Berry

When dry gas is injected into a reservoir containing a volatile crude oil, a significant amount of the reservoir liquid phase may become vaporized. The resultant rich gas phase, when subsequently produced, con-tributes to tank oil production. This contribution assumes greater importance, the more volatile the oil in-olved. Oil recovery may be sub-stantially greater than that predicted by conventional frontal-drive methods, which do not consider the vaporization equilibrium between the reservoir oil phase and the injected gas. A calculation method has been (developed to account for vaporiza-. tion of the reservoir liquid phase during gas-injectiorz operations, and for the tank oil production which results from this factor. Recovery performance calculations are presented for a reservoir containing a highly volatile oil. Tank oil recovery is calculated to be about twice that predicted by the use of the conven-rional frontal-drive equations. In contrastto usual pressure maintenance performance results, in which the gas-oil ratio rises at an increasing rate after gas breakthrough, the pre-dicated gas-oil ratio rises rapidly to about 12,000 scf/bhl and then rises much less rapidly. During gas inje-tion, most of the reservoir liquid phase contacted is evaporated by the dry injection gar. The gas-oil ratio during this period is dependent upon reservoir pressure. The higher the operating pressure, the lower the gas-oil ratio. The predicted behavior i., in accordance with laboratory PVT tests made to .simulate the vaporization behavior. In addition to recovery performance predictions, results of the calculation procedure include complete wellstrearn composition data of value in the design of gasoline plant facilities often used in con-rrction with gas-injection operations. INTRODUCTION In the cycling of gas-condensate reservoirs, dry gas is injected to maintain reservoir pressure during wet gas production and to thereby eliminate or reduce ultimate loss of liquids due to retrograde condensation within the reservoir. Gas injected into crude oil reservoirs has a dual function. It displaces oil to the producing wells and at the same time serves to partially or fully maintain reservoir pressure. Oil shrinkage which would occur upon pressure reduction is thereby minimized or eliminated. Accepted calculation methods are available'= for predicting recovery performance of either gas-condensate reservoirs or crude oil reservoirs which are being subjected to gas injection. In gas-condensate reservoirs, any retrograde liquid formed does not flow, and it is necessary to account only for the vaporization equilibrium between this liquid and the injected gas. Conversely, in normal crude oil reservoirs, both the oil and gas phases flow, but it has not been considered necessary to account for any vaporization of the reservoir liquid which might occur upon contact with the dry injection gas. Recently, high shrinkage reservoir fluids known as "volatile oils" have been found in increasing amounts. These oils are characterized by tank oil gravities above 4.5" API, solution gas-oil ratios above 1,000 scf/bbl, and reservoir volume factors above two. Special techniques have been devised for predicting depletion performance of reservoirs containing such oils.74.5.1; One of the characteristics of reservoirs producing volatile oils is that the reservoir gas phase carries a significant amount of oil which is recoverable as stock-tank liquid. This unusual vaporization be-havior implies that an appreciable amount of reservoir liquid would be vaporized upon contact of the oil with dry injection gas. In a gas-injection operation, tank oil recovery would he obtained not only through frontal displacement of the reservoir liquid by the injected gas, but also through production of the rich gas phase. This means that not only are improved methods needed to predict recovery of such oils from reservoirs undergoing gas injection, but it would also be expected that high oil recoveries might be obtained by such operations. When relatively dry gas is injected in to a volatile oil reservoir, phase equilibrium between the injected gas and the reservoir oil will tend to bc established. Initially the most volatile components, such as propane, the butanes and the pentanes, will account for most of the material transferred from the oil phase to the gas phase. As the partially stripped oil phase is contacted with additional dry injection gas, the heavier intermediate components, such as the hexanes, the heptanes and the octanes, will gradually transfer to the gas phase in increasing amounts. This is because the supply of lighter components in the oil phase dwindles due to the stripping action of the injected gas. This stripping action will usually continue to be effective down

By Arne Bergholm

Australian rutile was chlorinated in the presence of CO or carbon. The chlorination velocity in CO was found to be strongly influenced by temperature and proportional to the CO concentration, but independent of the Cl, concentration. In the presence of carbon, the reaction velocity is much higher. The reactivity of the carbon and the distance between the carbon and the rutile surfaces are important variables. The reaction velocity is approximately proportional to the Cl, concentration and independent of the CO concentration of the surrounding atmosphere. Experiments with fluidized-bed chlorination of carbon-rutile mixtures indicate that the motion of the bed has little influence on the reaction velocity. At low temperatures, the chlorination velocity of dense tablets is much greater than that of TiO, coke mixtures suitable for fluidization. The reaction mechanism is discussed. In the industrial production of TiCl, rutile is chlorinated in the presence of carbon. Disregarding intermediate steps, the reaction may be expressed by the following equations: The ultimate object of this study was to find out whether the reaction velocity was higher in fluidized bed operation compared with chlorination of pelle-tized carbon-rutile mixtures. From a literature survey and preliminary experiments it was learned that some basic knowledge about the reaction mechanism was needed for a good experimental design. Therefore the following sets of experiments were carried out: 1) Studies on the reaction velocity in the chlorination of rutile with CO as the only reducing agent. 2) Chlorination of separate rutile-carbon tablets. 3) Chlorination of rutile-carbon tablets at different temperatures with various kinds of carbon, various grain sizes, and various tablet-making techniques. This series of experiments was carried out not only with pure chlorine but also with mixtures of chlorine with argon, CO and CO,. 4) Chlorination of rutile-carbon tablets made in a strictly standardized manner. 5) Chlorination of static-bed rutile-carbon mixtures. 6) Fluidized-bed chlorination of the same mixture. The experiments 4 to 6 formed the final and direct test of the main question: Static bed vs fluidized bedo. Although there are many patents and papers dealing with the general aspects of chlorination, only few experiments from which detailed information can be obtained have been reported in the literature. Pamfilov and coworkersl3 have studied chlorination of TiO, with CO or carbon as the reducing agent. They found that the weight decrease per hour at 600o to 800°C amounted to 11 to 14 pct with CO and 45 to 51 pct with carbon. They suggest that phosgene might be an intermediate in the chlorination of TiO,. Takimoto and Hattori have chlorinated reduced titanium oxide (TiO) and found a very high rate of TiC1, -production. They proved that the composition of the gas from the chlorination of rutile-carbon mixtures contained mainly CO. They reported for instance 74.7 pct CO, and 5.6 pct CO at 800°C at which temperature the Boudouard equilibrium composition is 12 pct CO and 88 pct CO. Seligman and Segerchano6 have studied the chlorination of TiO. They proved that Ti0 and chlorine react rather rapidly at temperatures as low as 300°C. Above 400°C, the reaction was complete. At 500°C the velocity of this reaction was much higher than was chlorination of TiO, + C. McTaggart,7 Nishimura, et al. and Wilskam have chlorinated mixtures of carbon and various kinds of rutile or beneficated ilmenite. Nishimura, et al. also report the results from reduction of TiO, with H2, CO, or carbon. At 900°C only 1 pct Ti O is formed in 2 hrs. At 1100°C 23.1 pct Ti, 0, was formed if elementary carbon was present. No carbide formation occurred below 1400°C. McIntosh and Cofferll have observed that the CO, content of the exit gases from chlorination of rutile and calcined petroleum coke is appreciably higher than found in the Boudouard equilibrium. At 900°C the ratio (CO, /CO + CO) is about 80 pct, whereas the equilibrium value is about 2 pct. W. E. Dunn12 has studied the chlorination rates of several TiO,-bearing minerals with CO + Cl, or COCl . Chlorinations were carried out either in a fluidized reactor or a fixed-bed reactor, both having a 30-mm diameter. The results obtained in both reactors were comparable. It was proved that benefi-ciated ilmenite (i.e., ilmenite from which the iron oxide had been removed by chlorination) was chlorinated 10 times faster thanrutile. Sore1 slag showed an intermediate rate. When phosgene is used, the

Jan 1, 1962

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By H. J. Hutson

BRS, Inc. has utilized Carlson's Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming's Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

Statistical summary of the mineral industry world production, exports and imports 1964-1969 Published by Her Majesty's Stationery Office, London, on behalf of the Institute of Geological Sciences (1971) The Statistical Summary contains a wealth of care fully garnered information on the production, exports and imports of the principal minerals and mineral products throughout the world for the period 1964-1969, and it should therefore be of particular interest to economic geologists and others concerned with marketing and selling minerals. In view of the intractable nature of the source data it is quite an achievement to have published figures for 1969 so expeditiously. On picking up the Summary this reviewer instinctively compared it with the Annual Yearbook published by the United States Department of the Interior. The Yearbooks have been issued annually since 1882, and today each consists of a set of three separate books containing five volumes. Apart from abundant statistics on the domestic and international mineral industries, the Yearbooks are known for their perspicacious reviews and articles on a host of different facets of the world's minerals industry. Physically the Summary is a much slimmer publication than the Yearbook, and it contains no commentary whatsoever other than occasional footnotes. The principal contents are a series of tables showing production, exports and imports of fifty-nine of the world's more important minerals and mineral products. Each table shows the weight of the material produced or traded, by countries, with figures for each of the six years in adjoining columns. In some cases (e.g. diamonds) values in British currency are quoted in addition to weights. Most of the data have been abstracted from national reports and returns, although in some instances estimates are quoted where national sources are silent--as for example the production of platinum in South Africa. One wonders in passing if any useful purpose is served by the continued suppression of this particular figure. The four South African producers must surely be able to estimate each other's production fairly accurately by now, and one imagines that the national export figures can likewise be synthesised. This reviewer has two minor criticisms of an otherwise praiseworthy publication. Firstly it seems an unnecessary anachronism to perpetuate the split between 'Commonwealth' and 'Other' countries-the split can have little practical significance today. Secondly, what is one to make of the statement that the 1966-1969 figures for exports from Rhodesia of chrome ore and copper, to take two examples only, are 'not available'? It seems improbable that no estimates of these figures have been made since the imposition of sanctions, and inevitably one suspects that the figures have been excluded on policy grounds. Hopefully this problem will have been solved when the next Summary is published. M.J.M. South Africa, land of Challenge by Maurice Tyack France Interpresse, 323 pages, price R18-00. Is South Africa God's richest acre? In its mineral wealth it certainly is, but what of the many other complex overlays of emotions, traditions and racial problems? South Africa, Land of Challenge, provides the background. This is reported to be the first comprehensive documentary work of its kind on South Africa. It is a handsome volume measuring 12ft by 9f', is illustrated by at least 600 photographs of South Africa, more than half of which are in colour, and contains 21 original maps and charts. The book covers the full spectrum of South Africa's very existence, its geography, pre-history, its customs, countryside, natural resources and its cities. The more controversial categories are thoroughly discussed, the people, their policies and politics. Mr Tyack is eminently qualified to write on South Africa, being the author of over 20 books on other African countries and having spent more than three years of research, in the field, in South African archives and also in various libraries and museums, in preparation for this book. The book claims to be free of any party political bias and appears to be an honest attempt at a factual survey. However, a work of this magnitude will undoubtedly leave an impression on the reader and the tone of this book is decidedly patriotic. This is a useful reference work on South Africa that most South Africans will be proud to own. J.P.H. Ergonomics and physical environmental factors This publication by I.L.O. of a symposium in Rome in September 1968 has much useful information for the mining industry in regard to the health and productivity of its labour force. The first subject dealt with is mechanical vibrations. From this section it is clear that men who drive, for many hours each day, vehicles which vibrate in the 6 Hz range are subject to serious physiological and psychological effects. The former may show as changes to the vertebral column (which has a resonance in the 4-5 Hz range). The circulatory system is adversely effected by values in the 6-10 Hz range and the vision is impaired at between 40-100 Hz. Less definite knowledge exists of the effects of vibration on the hand-arm system from mechanical drills etc, although Raynauds disease of the blood vessels of the hand and degenerative diseases of the elbow and shoulder joints occur in men using drills which vibrate, respectively, in the higher and low frequency ranges. Industrial noise is extremely well dealt with and the latest knowledge is summarized. Clear information is given on the relationship between time of exposure to

By E. P. Whittemore

Experience with the ASC multipoint gas lift system was obtained in Colonia zone of the West Montalvo field near Oxnard, Calif. The wells in this pool produce from depths varying from 10,500 to 12,000 ft. Oil gravity is generally 14 to 15' API with a few extremes of 12 and 20" API. Some salt water is produced which causes some very viscous emulsions. Viscosities at 150F (which is the approximate wellhead temperature) vary from 5,000 to 100,000 SSU. Most of the production is by gas lift, although a few wells are produced by rod and hydraulic pump. About half of the gas-lift wells are on continuous flow and the remainder are on intermittent lift using large, ported, pilot-operated valves for single-point transfer of gas from casing to tubing. Gas-liquid ratios vary from about 6 to 10 Mcf/bbl of gross fluid lifted. Wells are produced to a 450-psi trap system. The following remarks will be confined to intermittent lift only, since this is the type of lift which has been achieved with the ASC valve system. The maximum gross fluid which has been produced by single-point intermittent lift is about 350 B/D in 3-in. tubing and 200 B/D in 21/2-in. tubing with gas-liquid ratios of approximately 7 to 9 Mcf/bbl. Some design changes could reduce this ratio. The ASC multipoint system has provided production as high as 480 BOPD in 21/2-in. tubing with gas-liquid ratios just under 4 Mcf/bbl. To be able to apply the multipoint system, it is recommended that a detailed explanation be obtained concerning transition-point pressure and stabilizer setting—what its significance is to the string design, how it may work for or against the operation of the well, how it is related to tubing sensitivity and how it affects the unloading operation. The unloading operation may only be of academic interest in a technical paper, but to the production foreman, unloading and setting the valves in operation is a very real problem and should be understood in detail. One item touched lightly in the paper was the unloading valve. This valve controls the maximum pressure at which the well can be operated. When lifting heavy viscous fluids, it is most important to set this valve for the maximum possible realistic operating pressure at the surface. If the well lifts easily, it is simple to set the ASC valves at a lower operating pressure and the unloading valve will remain closed; but if the well happens to be heavier to lift than anticipated, it may be desirable to operate on the unloading valve itself and use all the energy obtainable at the bottom of the hole. In the Colonia pool very heavy wet-gas gradients are experienced due to the viscosity of the liquid and the dense mist which is left behind a slug of fluid. There are many combination strings of 3- and 21/2-in. tubing. This aggravates the wet-gas gradient problem and provides wet-gas gradients of about 50 to 70 psi/1,000. An advantage which multipoint lift has provided is increased slug efficiency through better maintenance of pressure under the slug and decreased fall back as the slug passes up the tubing. By using multipoint injection, wet-gas gradients have been reduced to about 30 psi/1,000. This has reduced bottom-hole operating pressure and given a production increase. The ASC valve is not a simple device. It's operation is difficult to understand, and it must be understood to be used efficiently in gas-lift design. Operating problems are difficult to diagnose—whether they be caused by the fluid lifted, valve malfunction, lift gas rate, or operating pressure. Calculations and reasoning are required to find out what is causing the problem. Inherent in the ASC valve is the inability to create large pressure differentials across a slug. Large differentials may be required to overcome the inertia of very viscous fluid as it is being accelerated in the bottom of the hole. This is tied back to the design of the unloading valve and is one reason for the importance of setting the unloading valve for the highest possible operating pressure. ~u; to the narrow spread the ASC valves provide, it is impossible to cycle slower than about 24 cycles/day on choke control. If small production of 150 BOPD and less is expected, a surface time-cycle controller will be required if the most economical operation is to be achieved. To achieve a satisfactory operation, the operator must keep a record of any changes made in the operating pressure of the ASC valves. Anything which may cause changes in casing pressure in excess of the stabilizer setting will change the valve operating pressure, and if this is not noted from daily inspection of the well casing-tubing pressure recorder charts, the operator will lose control of the well. Significant results can be achieved using ASC valves; however, considerable knowledge is required to design with them, and attention to detail is required for satisfactory field operation.

Jan 1, 1965

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By N. Van Wingen, Norris Johnston

Laboratory flood pot testing of California sands has progressed to a considerable extent in the past 18 months. Flood evaluations have been carried out on over 200 large core samples. Many of these were heavy oil sands of high permeability and completely unconsolidated in nature. The oil frequently formed a bank, though some of the oil was recovered in the subordinate phase of the flood, by viscous drag. Flood pot recoveries as high as 1400 bbl/acre ft have been recorded. Reservoir analysis suggests a conformance factor of 0.4 to reduce laboratory recovery to probable field practice. Oils with viscosities up to 1800 cp have been successfully handled in flood pot evaluations. The shallow, loose sands are not well adapted to the application of- high pressures to offset the high viscosities. INTRODUCTION Secondary recovery may be said to have started 60 years ago when accidental floods occurred in the Bradford sand in Pennsylvania. About 1921 artificially conducted water drives came into extensive use and since that time the great Bradford field has been almost completely subjected to water flooding. During the last 30 years, most of the known medium and deeper production in California has been discovered and is being exploited by primary recovery methods supplemented in some instances by high pressure gas injection. The California area is just beginning to feel the need for secondary recovery in view of an unprecedented market demand and the rapidly rising cost of new pool discoveries. With the presently recognized desirability of secondary recovery in California, there must also be appreciated a number of serious differences between the water flooding problems here as compared to the territory east of the Rockies. California sands are generally thicker, and are frequently soft and argillaceous. The oils are often heavier and asphaltic. Much of the oil is below 15°API, occurs at shallow depth, is cool and free from appreciable dissolved gas, which results in relatively high reservoir oil viscosity. Secondary recovery is particularly beneficial where primary recovery has been poor and where no natural water drive exists. These conditions apply particularly to the heavy, shallow, clean production from soft, often argillaceous California sands so abundantly found at depths less than 1500 feet. Often, too, there is a totally insufficient supply of water of satisfactory quality to inject at a reasonable cost. Also, the crude oils are priced far below the premium Bradford crude. Although these and a number of minor problems beset the operator desirous of starting secondary recovery, great progress has been made in the past few years in finding how to adapt previous Mid-Continent and Eastern experience to water flooding in California. There are about nine projects for subsurface injection of water which can be said to classify as secondary recovery operations. Subsurface water disposal would so classify when the sand receiving the water is a nearby oil producer, as is often the case. When water is injected subsurface into a barren sand, the operation does not classify as secondary recovery. Several of the most active operators avail themselves extensively of preliminary engineering and laboratory work to guide their decisions, while others enter small scale flooding operations directly in the field. It is the laboratory work pertinent to several of the California secondary recovery projects that this paper discusses. PURPOSES OF LABORATORY FLOODING TESTS Experience in areas where water flood operations have been carried out has indicated that careful engineering planning is an important requisite for subsequent economically successful field operation. Floods that fail are more frequently those where operations were instigated without a prior engineering investigation to determine the effectiveness of the injection fluid as an oil displacing medium. Laboratory data are essential in the evaluation of an oil property for secondary recovery possibilities. Success or failure of secondary operations can under certain special circumstances be determined directly by cores and their subsequent routine analysis. This is particularly the case where flushing of the cores in the course of coring is negligible and where the results of the analysis can be compared with existing secondary recovery operations. Where these conditions cannot be' fulfilled, the application of core analysis is more limited. In such event, the results obtained by water flooding core samples in the laboratory have been found to be of prime importance. Cores may be flooded "raw" as taken from the well or in the event flushing and depletion of the cores in the process of drilling are major factors the fluid content may be artificially restored prior to the flooding. Laboratory studies should also be made to determine the suitability of the water selected for injection. Thus interaction between injected and formation water may cause precipitates to be formed which may plug the sand. Even more important, especially to California operations, is the possibility of the hydration of formation clays by the injection water. The aims of flood pot and associated tests are basically to determine the residual oil saturation after flood, the water-oil throughput ratio and to establish whether an oil bank is formed. Additional information which can be obtained from flood pot tests pertains to the pressure differential required to effect displacement, the relative permeability to oil in the oil bank and the relative permeability to water in the watered out region behind the bank.

Jan 1, 1953