Search Documents

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By AIME AIME

IN view of the approaching visit to Japan and the Imperial Steel Works at Yawata by our members, the following notes on present conditions in the industry there will be of interest. The data were collected by the representatives of the Bureau of Foreign and Domestic Commerce in Japan and are furnished here through the courtesy of the Department. In connection with the proposed suspension of both new and old Government undertakings and the general depression in building, which is expected to result from the retrenchment policy of the Government, some cuts in iron and steel prices have been made by dealers. It is expected that the Yawata Steel Works may reduce its round bar prices for November delivery by 1 yen.

Jan 1, 1929

By AIME AIME

THE Petroleum Division held a very successful meeting in Los Angeles, Oct. 4 and 5. The meeting was held on the eighth floor of the Chamber of Commerce building, the first day being devoted to technical sessions. Seventy-five members were registered before the opening of the first session. Glenn D. Robertson, vice-chairman of the local section, opened the meeting and introduced Edwin Higgins, managing director of the California Oil and Gas Association, who gave an interesting talk on the recently enacted gas conservation law in California. He explained that the law is an experiment which will be watched with a great deal of interest. The purpose of the law, which went into effect on Sept. 1, is to curb wastage and over-production of gas,

Jan 1, 1929

By W. Lo, M. Brothers, G. Oprea, G. Richard, T. Troczynski

Magnesia-chrome and chrome-magnesia are the most used refractories in contact with iron-rich non-ferrous smelting slags. The corrosion by slag always brings chromium oxide into the slag, causing the precipitation of crystalline phases at the process temperature. This secondary effect of the chromium-bearing refractory dissolution was studied in this work, emphasizing the effect of the other chemical components of the slag at various temperatures. The experimental results showed that the presence of chromium and lead contribute, although in different ways, to the formation of complex spinel phases and their precipitation at temperatures in the range of 1250-1400°C. The XRD and SEM/EDS results were discussed for refractory-slag mixes containing 0-20% Cr2O3 and 0-11% PbO.

Jan 1, 2004

By G. Gaidajis

In this paper, a semi-qualitative methodology is presented and then applied to an aluminium extrusion industrial facility in order to perform an initial environmental assessment. The results of the assessment enable an improved understanding of the environmental performance of the facility and more importantly identify the areas of significant environmental concern. Following, the application of case-specific sustainability indicators related with the areas of significant environmental concern, leads to a more comprehensive sustainability assessment. The applied two-step approach offers a quick and reliable environmental assessment and help focusing on the most environmentally problematic areas. Moreover, the follow-up of the specific indicators seems to be appropriate for the improvement of the environmental performance of the examined industrial facility.

Jan 1, 2008

By T. Watanabe, M. Nakagawa, K. Kimapong

Lap joint of A5083 aluminum alloy and SS400 steel was produced by Friction Stir Welding (FSW) Process. The effect of welding parameters such as rotational speed, traverse speed and tool dimensions on the mechanical properties and the interface microstructures of the joints were investigated. FSW process could successfully produce the lap joint between A5083 aluminum alloy and SS400 steel. The variations of rotational speed, traverse speed and pin depth of a rotating tool gave rise to various characteristic interfaces of the lap joint and had conspicous influences on the joint properties. The increase in hard and brittle intermetallic phase and defects formed at the interface of the joint decreased the mechanical properties such as the shear load of the joint.

Jan 1, 2004

During the nineteen months in which our country was actively engaged in the war, the United States Shipping Board Emergency Fleet Corpn. expanded the shipbuilding capacity of the United States from an unimportant position among the world's producers of ocean-going tonnage to first place. At the same time it increased the overseas merchant fleet of the United States from a negligible quantity to second place. The shipbuilding program has been greatly reduced since the signing of the armistice. There have been suspended or canceled contracts for 754 ships aggregating 3,797,825 deadweight tons, which would have cost $797,564,276 to complete. The cost of canceling these contracts will be about $202,853,456, and the saving effected by cancelations will approximate $594,710,820.

Jan 7, 1919

THE illustration below shows the design of the face of the clock to be erected as a memorial to the American engineers who gave their lives overseas in the World War. It will be placed in the tower of the library at Louvain, which has been rebuilt through contributions from America. Large clocks seldom have figures on their faces, and each hour on this one will be marked by a gold star, the four faces containing 48 stars, one for each State of the Union. Contributions toward the memorial have been received from every one of the States, and from Alaska and Hawaii as well, but additional subscriptions are invited by the Com-mittee which is arranging for the memorial.

Jan 3, 1928

By Walter Wood

The specifications for locomotive-cylinders, which are given in a separate paper at this meeting, have been prepared so that castings (upon the successful use of which so much depends) shall be made to conform to standards that will yield good results. After the essentials, which go with a sound and perfect cauting, the requirements to be borne in mind are those concerning the quality of the material. These have been determined from the actual practice of the largest users,—representatives of the American Locomotive Company, the Baldwin shops, and the Pennsylvania Railroad being upon the Committee. The results called for by the test-bar have been carefully checked by actual experiment upon metal that has given satisfactory service in cylinders.

Jan 1, 1905

By Xu Zhong

The theoretical limit to smelting rate and possibly the size of a smelter is dependent on the rate of heat transfer, and the chemical kinetics of both sulfur removal and minor element volatilization. The fundamental kinetics of volatilization of minor elements such as As, Sb, Bi, and Pb from matte and white metal is being investigated. It has been shown that the molecular form of trace elements in matte depends on the chemical potential of sulfur and the propensity for the minor element to form a sulfide. The impact of the variable molecular form of the minor elements on the volatilization kinetics is unknown and is under investigation in this study. The experimental technique is reviewed and preliminary results are reported in this manuscript.

Jan 1, 1995

By W. Randolph Van Lewis

In determilling the relative rate and in fi~lding the point where different inlpurities containecl in copper-matte are eliminated during the process of a converter-blow, the follo~ving results were obtainecl : A converter was selected which was starting on its sccolld charge. The first charge after lining had finished its copper " hot," and conseqaently no copper was adhering to the sides of the lining. All the copper and granulated slag from the previous charpc mcrc dumped, thus removing ally possibility of " salting " the matte to be tested. The coliverter worked fast and well during the entire test. Periods of ten minutes were selected. The converter mas brought from the stack to secure each sanlple of matte to be

Jan 1, 1904

WM. A. COWAN, Brooklyn, N. Y. (written discussion*). -This is evidently an excellent continuation of the work described in the article "An Investigation of Fusible Tin Boiler Plugs" by Messrs. Burgess and Merica.1 The present paper gives information of much value in con-nection with the manufacture and inspection of fusible boiler plugs, and the investigation of the cooling curves of tin with various other metals close to the tin side of the diagram is very interesting. These curves corroborate in all cases, except that of antimony, the diagrams given by other investigators. However, only the liquidus curves of the thermal equilibrium diagrams are given, except for copper-tin alloys where one branch only of the solidus (representing the freezing, of the eutectic)

Jan 11, 1919

By J. F. Labuz

Fracture tests were conducted on subsize specimens of Charcoal granite to demonstrate that the extent of the nonlinear region at the crack tip can be significant. The model of the fracture process considers an effective crack length as a traction free portion plus a process zone where closing stresses act; this zone is identified by microcracking and interlocking. A singularity is allowed at the effective crack tip. The effective stress intensity factor is the superposition of the stress intensities due to the effective crack and the process zone. By assuming that the closing stress is a linear function, it is shown that a process zone length of approximately one-third the effective crack is needed to match the compliance-determined crack length.

Jan 1, 1984

By Ralph H. Sweetser

When a furnace-manager is '(blowing in," he generally has no time to consider the composition of the waste gas, and does not bother with it, except to take care that he does not get " gassed." Moreover, the analysis of the gases while the wood is still burning has not much to do with the economy of the normal working of the furnace; yet, on account of the deadly effects of the " blowing-in " gas when inhaled, and of its high explosive qualities, it is interesting to know its composition. In the Transactions there is no record of the analysis of the gas during an up-to-date " blowing-in." Even in Mr. Whiting's admirable paper (Trans., xx., 280) the reported analyses did

Jan 1, 1899

By Allen L. Hatch

Perhaps the greatest challenge to the non-ferrous extractive industry, aside from discovery and cost reduction, is the continuous effort toward the total recovery of metals. This is-and must continue to be-a joint endeavor on the part of the miner and the smelter, the first to trend constantly toward that form of concentration most amenable to the smelter and the latter to upgrade technical efficiency on the product delivered. What follows will be a smelter's-eye view of the relative value of gold, silver, copper, lead and zinc as they each are contained in copper, lead and zinc concentrates. The variety of combinations is obviously of such a magnitude that it will be necessary to restrict the observations to fundamental concepts.

Jan 1, 1966

By J. Partyka

Adequate ventilation is a main concern if Lockerby Mine near Sudbury is to be expended. This study investigate a two-fold problem: (1) the new pressure and volume requirements of the main fans due to the theoretical. deepening of the mine, and (2) the effect of the natural ventilation pressure on the main fans. Field data was analyzed with the aid of a newly developed network simulation program, VNETPC Version 3. 0. The density change throughout the mine is accounted for by performing all computations at reference density. Results of the investigation indicate that the existing fan system must be supported by three to five additional underground fans as well, the density effect is significant. If neglected, it will greatly alter the simulation results

Jan 1, 1991

Chester Wells Purington was killed at Yokohama on Sept. 1, 1923, in the Japanese earthquake. Mr. Purington was born in Boston, Mass., Oct. 27, 1871. He prepared for his entrance to Harvard at the Boston Latin School and graduated from Harvard in the class of '93. He started out soon thereafter investigating gold deposits of the Appalachian system in the South and in 1895, made atrip to Alaska, investigating the gold deposits of that territory. The summer and fall of 1896 found him in the San Juan country of Colorado examining the gold and silver properties in the Telluride and Rico districts and in the La Plata Mountains. In the meantime, he had served on the economic staff of the U. S

Jan 1, 1924

By J. Hanna, J. Jung

Researchers at The University of Alabama have recently developed a two-step method for the treatment of phosphorus sludge. The process includes the bulk removal of phosphorus by physical separation techniques followed by the remediation of the residual P4 in the sludge using a novel, wet, air-oxidation technique known as "HSAD." Tests made on electric furnace, phosphorus sludge samples have demonstrated that an essentially complete and fast removal of the contained P4 can be achieved by the HSAD wet oxidation treatment. Further studies were made to determine the applicability of the two-step process to sludges of different origins, pretreatments, storage conditions and P4 contents. The present work discusses the mechanisms and factors controlling the HSAD, wet, air-oxidation remediation approach.

Jan 1, 1993

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant (WIPP) provides for the unparalleled ability to ensure the safety of the workers, the public and the environment. Although small spatially, the system can vary the airflow from 31.2 to 217.1 m3/s (66,000 to 460,000 cfm). The system can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and they can be adjusted from the surface if necessary. A ventilation remote-monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based real-time mine-ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2003