Search Documents

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By I. N. Bayless

The subject of Premium Payments for Mechanical Loading was given consideration by the management, having in mind they would prove an incentive for increasing the tons per man shift, make for a lower production cost and allow the ambitious workman an opportunity to augment his earnings over the regular day wage rate, a standard of performance having been established by the operator which would be expected from the employee. Any performance above the standard is looked upon as a saving to the operator of which the employe benefited to the extent of receiving a certain percentage of the saving effected. The premium must be high enough to be worth while to the employee and low enough to in¬sure a saving to the employer. This method of sharing tends to pay men in accordance with their ability and effort. One of the principal advantages of this method of sharing is that a better class of labor may be attracted. Greater earnings furnish an incentive to increased tonnage. Workmen who prove themselves aggressive are readily noticed by supervisors, and, by shifting men to different places and to different working conditions, the crews are made more efficient and the inefficient workmen may be singled out and eliminated, thus permitting better results and better operation of the mechanical loading equipment. This is also evidenced by the fact that men become their own competitors, also working in competition with other crews. In order to do this, without neglect to the care and protection of the loading machines, men are educated to the proper handling and care of the machinery, keeping it in shape and everything clean in general, which has shown good results.

Jan 1, 1932

By Frank Rieber

The discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.' The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as is possible with the more pronounced anomalies.

Jan 1, 1929

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By Murray C. G

A database of over 1300 earthquakes has been used to investigate the relationship between seismicity and tectonics in two areas of eastern Queensland and NE New South Wales. These areas have been monitored by several networks that were installed primarily to monitor seismicity associated with the impounding of large reservoirs. Events that occurred prior to the installation of these networks have been excluded from the analysis because they have large uncertainties in location.Seismicity in SE Queensland and NE New South Wales is concentrated in the coastal regions. Activity also extends off the coast of Queensland and beyond the continental shelf. The coastal activity is mainly within the New England Fold Belt. An area of the fold belt overlain by the Clarence-Moreton Basin is also active. There is an area of activity near St. George that correlates to the Wunger Ridge. Fraser Island and the adjacent onshore area, near Maryborough, are notably aseismic.Within the New England Fold Belt there is a NNW trending zone of concentrated activity that includes the South D'Aguilar Block and the Esk Trough as far as Gayndah. The Nambour Basin, the Gympie Province, and the southern portion of the Yarrol Block are significantly less active.Composite focal mechanisms of several groups of accurately located earthquakes in SE Queensland indicate predominantly reverse faulting. This faulting is the result of the crust being compressed horizontally in a NE-SW direction.Activity in the Burdekin Falls Dam area of central eastern Queensland is confined to the Drummond and Bowen Basins. There is also significant activity offshore from Townsville and Bowen.

Jan 1, 1990

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By W. F. Holbrook, C. E. Wood, E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and .its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. TYPES OF FURNACES Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1938

By Jeff Gore, Jack Dermody, David Gribble, Brett Macaulay, Bart Sharpe, Paul Klaric, Paul Thornley, Ben DeVries

Optimal Fragmentation in Block Caving is difficult to achieve as it is generally defined by the rock mass itself and the way in which the cave is initiated. The lower portion of the cave has even less chance as the material has little time for self comminution. Blast Preconditioning of the Block Cave is designed to engineer the lower section of the rock mass to produce material of a suitable size to assist in the initial cave propagation and improve initial drawbell productivity. At Cadia East a plan was developed to drill 150-metre long, vertical up-holes from the undercut level and blast them fully confined to produce fractures in the rock mass. The blast itself was a simple undertaking. However, in the year preceding the first production blast, all aspects of the process were designed, tested and refined across multiple trials. As this type of challenging application had not previously been encountered in Australia there were many unique situations to address. Products and systems had to be developed and adapted to overcome these challenges. These included: Formulating and manufacturing an explosive that is robust and of a high VoD; designing and manufacturing easy to use electronic initiation systems; and, designing pumping systems to combat high head pressures to allow for successful and safe loading of the holes. Close collaboration with the customer ensured that the trials culminated in successfully blasting a hole containing almost 3.3t of explosive. These trials have since led to the blasting of four holes instantaneously, which contain almost 13t of explosive. This paper describes the various components of the system, the challenges and the final result.

Jan 1, 2013

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By E. J. Gleim

"When permissible equipment is first placed in a gassy mine, those in charge may not realize the amount of attention and care they must give it if they intend to secure its full value as safety equipment. If permissible machines are installed as a safety measure, then they must receive regular, intelligent inspection and upkeep to forestall the development of unsafe features.Certain fundamentals have been followed in the design of this type of equipment in order to minimize the possibility of its igniting gas and dust. Hence, some knowledge of these fundamentals is essential to the inspector or official charged with the duty of ascertaining the condition of permissible machines with respect to safety. Familiarity with the constructional details of a machine is of first importance in making a thorough inspection of it. A knowledge of Schedule 2C3 which gives the requirements for practically all types of motor operated equipment receiving the United States Bureau of Mines' approval is also a requisite.There are certain special features in the construction followed by different manufacturers that can not be made clear for the purposes of inspection except by a lengthy description which would be inappropriate in this paper. There are, however, some general points that are applicable to the inspection of any machine employing trailing cable for connection to the power supply, also some that apply to any permissible storage-battery locomotive.The following list, based on the writer's experience in making field inspections, gives these general points in the form of questions which may he used as a guide by the inspector. A brief explanation is given after each question so that the reason for checking up on each point will be understood.1. Is a U. S. Bureau of Mines' approval plate attached to the machine? (Such a plate is necessary in order to establish identification as a permissible machine.)2. Is approval plate clean?(The plate should be clean so that the precautions enumerated on it are readable.)3. Is trailing cable protected by a fuse or other automatic circuit-interrupting device?(Trailing cable must have a fused trolley tap or other suitable means for short-circuit protection in case the cable is run over or splices fail. Proper fusing will minimize the possibility of fire in the cable reel.)4. If a trolley tap is used, does it contain a fuse of the proper capacity? (A piece of trolley wire or, too large a fuse may entirely defeat the purpose of fusing.)5. If a fused trolley tap is not used, how is connection made to the power supply? (The end of the trailing cable must be fitted with an insulated arrangement to minimize shock hazard when connecting the cable to the power supply.)6. Are the main fuses (or overload relays) of the correct size (or setting) for protection of the machine against overload?(Too large a fuse or too high a setting of the overload relay will permit damage to the machine by abuse through sustained overloads.)7. If the machine has a headlight, does the headlight circuit have overload and short-circuit protection?(The wiring of the headlight circuit on a machine is usually of a smaller size than that for the main circuits and therefore requires fuse protection proportionate to the size of wire.) Note: This same question may be asked relative to coal drills sometimes mounted on a machine."

Apr 1, 1932

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

A symposium concerning "The Image of the Coal Industry" was presented at 2:00 p.m. in the Conference center and chaired by Charles W. Margolf, RMCMl Program Chairman and Vice President, Western Coal Development, W. R. Grace & Co. MR. McKEEVER: I'd like to do one thing and that's to introduce our Program Chairman, Charlie Margolf, who will be handling this portion of the program. Charlie and I have been acquainted since late 1973. He has worked together with me on several projects at W. R. Grace here in the west; a dear friend and one that I just want to say thanks to again. I think I have a little token of that appreciation here for Charlie. Here you are Charlie. (present given) I turn the command over to you. Mr. Margolf, a native of State College, Pennsylvania, received a Bachelor of Science Degree in Industrial Engineering from Pennsylvania State University in 1950 and a Juris Doctor Degree from University of Pittsburgh School of Law in 1953. His professional experience has beem as an attorney in the Law Department of Reynolds Metals Company, Richmond, Virginia, where he served as legal counsel to the Geological Department the mining subsidiaries of the parent company both foreign and domestic, the Power Department and the Oil and Gas Division. He was closely associated with Reynolds Mining Corporation's project at Lake DeSmet, Wyoming, from its inception in 1954 and became Manager of the Wyoming Division of Reynolds Mining Corporation when it was established in 1966, holding that position until September 1972 when he joined Cameron Engineers, Inc. of Denver, Colorado as Vice President in charge of its coal, water and environmental activities. Mr. Margolf joined W. R. Grace & Co. in January 1974 as Director of Western Coal Operations. Memberships are held in the Virginia Bar Association, the Wyoming Bar Association, the American Bar Association and its Section of Natural Resources Law, the Wyoming Engineering Society, the Colorado Mining Association, the Rocky Mountain Coal Mining Institute which he has served as vice president for Wyoming, the Society of Mining Engineers of the American Institute of Mining, Metallurgical and Petroleum Engineers, the Minerals Information Committee of the Denver Chapter of AIME and the Denver Coal Club which he has served as Chairman of its Board of Directors. He has also been a member of the Montana Coal Council and served as a director, the Wyoming Water Development Association which he has served as a director for industry and as first vice president and the Wyoming Mining Association. He has been reappointed by Governor Lamm to the Governor's Scientific Advisory Council. He was appointed by the Federal Power Commission, Gas Policy Advisory Council, to its Supply- Technical Advisory Task Force - Synthesized Gaseous Hydrocarbon Fuels and served as Vice Chairman of that Task Force. He has been reappointed by the Secretary of the Interior to the Solid Fuels Unit, Department of the Interior, National Defense Executive Reserve. He also serves on the Advisory Council to the Industrial Ecology Institute of the Colorado School of Mines and was recently elected a member of the Board of Directors of ROMCOE (Center for Environmental Problem Solving). Chairman Margolf presented the symposium from the perspective of: ? A local government official - The Honorable Michael Enzi, Mayor of Gillette, Wyoming ? A former state government official - Harris D. Sherman, former Director of the Colorado Department of Natural Resources ? A representative of a national environmental. organization- Robert Golten, Senior Counsel, National Wildlife Federation ? A representative of the printed news media- Ralph Looney, Editor of The Rocky Mountain News in Denver

Jan 1, 1982