Search Documents

By C. W. Phillips, R. S. Busk

With most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and micro-porosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. Measurement OF Grain Size By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscopc are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Abom, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurcment. The A.S.T.M. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method4 or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.5 The chart was constructed by photographing at Ioo diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargemcnt of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By John M. Hartman

On May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings mere provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November loth, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous upand-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow stems that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in firebrick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to tarn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By M. S. Hunter, W. L. Fink, R. H. Brown

Early workers attempted to study the structure of alloys by measurement of equilibrium electrode potentials in aqueous solutions containing ions of the metals from which the alloy was made.' The method was subject to such limitations (e.g., the difficulty in attaining electrochemical equilibrium at low temperatures) that it has not been widely used by metallurgists. Recently, Seltz and co-workers have introduced a greatly improved method for studying alloys by measurement of equilibrium electrode potentials in molten salts.2"4 The mathematical treatment is the same, of course, as for equilibrium potentials of amalgams in aqueous solutions.5 This method will probably find extensive use, since it makes possible not only the determination of phase fields of equilibrium diagrams but also the determination of certain thermodynamic quantities which can be used advantageously in metallurgical calculations. However, the method presents difficulties. With many metallic and alloy electrodes, reversibility is not readily obtainable. Also, the difficulty of obtaining suitable material from which to make the cells is increased as the temperature is increased. Moreover, the necessity of carrying out measurements in a vacuum requires additional apparatus and introduces considerable difficulty, especially at the higher temperatures. Apparently, no consideration has been given heretofore to the metallurgical use of irreversible electrode potentials that exist when a specimen is immersed in a suitable aqueous solution at room temperature. The apparatus and the method required for such measurements are very simple, and if the results of such measurements could be demonstrated to be reproducible they might be very valuable in studying the structure of alloys. The method would not have the scope of that developed by Seltz and his co-workers because no thermodynamic quantities could be calculated from the data. However, the utility and the simplicity of the method might warrant extensive use for the determination of phase fields and similar applications. Theory of Irreversible Potentials A brief review of the theory of irreversible potentials will be given before showing how to interpret the potential readings in terms of alloy structure. It is known that heterogeneity of a metal surface in an electrolyte will produce points of different potentials, with the result that current flows between these points and electrochemical reactions occur. The points at which oxidation reactions are localized are known as anodes, and those at which reduction reactions are localized are known as cathodes.6, 7, 8 For the benefit of those who are not familiar with the terms anode and cathode as applied to a primary cell, the potential difference between anode and cathode of such a cell can be measured when

Jan 1, 1941

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By Torgrim Eftestoel, Leif Olsen, Ove Sandberg

IN the vertical contact Soederberg electrode for aluminum furnaces more or less serious cracks are sometimes formed in the electrode, with harmful effect on furnace operation. The problem of crack formation has been studied on a laboratory scale to obtain a better understanding of this phenomenon. The primary cause of crack formation is the shrinkage of the electrode carbon, which is opposed by the normal thermal expansion of the steel contact studs. The forces thus set up are active in the temperature interval from which the electrode obtains a rigid structure (450" to 500°C) to furnace operational temperature (950°C). A visualization of our reasoning is given in Fig. 1, which shows the different behavior of mild steel and electrode carbon during baking. Research work performed to determine relationships between crack formation and shrinkage will be described. A brief description of the method developed for measurement of shrinkage will be given, as well as a critical analysis of this method. Also, raw material quality and paste composition variables will be related to shrinkage phenomena. Laboratory Test of Crack. Formation To test the tendency toward crack formations of Soederberg electrodes from different pastes, experiments were performed to simulate conditions of actual commercial electrodes, and are described as follows. A cylindrical test electrode is prepared by tamping the electrode paste to be examined in a sheet iron casing, 350 mm diam by 700 mm height. The casing is perforated, with the holes (2 mm diam) 50 mm apart, to facilitate the escape of volatile matter during baking. A cylindrical steel stud of actual service size, 100 mm diam, is welded eccentrically to the bottom steel plate, and protrudes up through the paste. During baking, a crack may thus occur in the weaker part of the test electrode. The electrode is baked by lowering the assembly slowly into an electric furnace, the temperature of which is kept constant at 900°C. After baking of the electrode, the sheet iron casing is removed and the electrode inspected for cracks. The pictures in Fig. 2 are of three different pastes baked according to the present method. Electrode 1 has a large crack; electrode 2, a somewhat smaller one; and electrode 3, only a minor crack. As will be seen from the simplified sieve analysis diagram of Fig. 2, the compositions of the pastes in question are very different. This subject will be discussed later in greater detail. Crack Formation and Shrinkage Relationships It is well known that shrinkage occurs in coke in the higher temperature ranges of coal

Jan 1, 1958

By C. W. Phillips, R. S. Busk

WITH most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and microporosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. MEASUREMENT OF GRAIN SIZE By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscope are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Aborn, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurement. The A.S.T.M.. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method' or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.', The chart was constructed by photographing at i00 diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargement of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By R. A. Bergman, C. J. B. Fincham

THERMODYNAMIC properties of many high-temperature systems containing sulfur, such as slags, metal sulfides, and solutions of sulfur in liquid metals, have been studied by means of equilibration with known gas mixtures.'" This method presupposes a complete and accurate knowledge of the thermodynamic data for all possible components of the gas phase at high temperatures. However, a survey of the data available up to 1952 on the thermodynamics of gaseous sulfur species and compounds, by Richardson and Jeffes,' showed that there was considerable uncertainty in the values of the free energies of formation of S, SO, HS, and CS. In many cases, this uncertainty made it impossible to decide whether or not these species would form a significant proportion of the sulfur present in the gas phase in any given system. After the review by Richardson and Jeffes had been published, St. Pierre and Chipman6 measured, by an indirect method, the free energy of formation of SO. This also enabled a clear choice to be made among the three possible spectroscopic values for the dissociation energy of S2 into atoms10 thereby determining the free energy of formation of S from S2, and fixing the free energy of formation of HS more accurately" The main purpose of the present investigation was to measure the free energy of formation of CS, which was still in considerable doubt. For example, at 1600°C, it could be estimated to be +6 +25 kcal per mole,* most of the uncertainty being in the * Based on the dissociation energles of CS6 and S2,5 the heat of sublimation of graphite, and, the assumption that the entropy of formation of CS is the same as that of CO. value of the dissociation energy." A secondary purpose of the investigation was to determine more accurately the equilibrium sulfur pressures over dilute solutions of sulfur in carbon-saturated liquid iron. General Method Dilute solutions of sulfur in liquid iron, saturated with carbon, were brought to equilibrium at 1600" and 1800°C, with known gas mixtures consisting, initially, of A and CS2. After equilibrium had been reached, the melts were quenched and analyzed for sulfur. In the high temperature region of the furnace, an equilibrium was set up between the various possible sulfur species and compounds in the gas phase; namely, CS2, CS, S2, and S. (It can be calculated that the amounts of S6 and S, are negligible at these temperatures:) Morris and Bueh17 and Kitchener, Bockris, and Libermana had previously studied the corresponding

Jan 1, 1958

By Lloyd R. Jackson

IN the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: I. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalid strains in determining the effect of plastic flow on the work-hardening of metals. FUNDAMENTALS INVOLVED IN PLASTIC FLOW In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Never- the less, as will be shown, metals are close enough to being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of .isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables-six being stress variables, and six being strain variables. ) From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining. This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses . and one for strains) that have received most attention are the following: [ ]

Jan 1, 1946

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By Joan M. Hartman

ON May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings were provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November 10th, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous up-and-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow steins that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in fire-brick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to turn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By J. D. McClung

INTRODUCTION The ever increasing demand for coal sues that meet exacting specifications has made necessary the installation of thousands of dollars worth of crushing equipment by the coal industry. At one time the operator at- tempted to recover as much lump as possible but today he is confronted with the necessity of crushing to facilitate the mechanical cleaning process and to meet the demand for a variety of uniform sizes. As a matter of fact, about 65 percent of the coal mined in the United States today goes through preparation plants where it is crushed and cleaned. One becomes more aware of the importance of the art of comminution when it is realized that practically all of the operations in mining are involved in comminution in one way or another. Whether the coal is mined conventionally or by continuous miners it is separated from the solid by a breaking, ripping or milling action which essentially amounts to a comminution operation. Even degradation resulting from material handling from the mine working face to the preparation plant might in a broad sense be so classified, Then of course crushing is usually necessary in the plant before the coal is ready to be marketed. THEORY Despite the various comminution operations there is a lack of satisfac- tory information concerning the fundamentals of crushing and their relation to the variable factors associated with the operation. There are certain laws and theories on mechanical reduction, such as those of Rittinger, Kick and Bond that are helpful and useful. The difficulty in developing exact mathematical relationships for specific crusher applications is due to the many variable physical characteristics found in coal. Hardness, as measured by the Hardgrove grindability index, is one parameter that has been used for years to determine the resistance of coal to comminution. While the coal properties as measured by grindability are complex, recent work has shown that a high correlation exists between the grindability of some coals and their petrographic analysis. Early research on the hardness of petrographic entities from an Illinois coal2 demonstrated that durain was the hardest constituent followed by clarain, vitrain and very soft fusain. Other research demonstrated that, for different size fractions of the same coal, a wide variation in hardness commonly exists. For example, the fines in about half of 39 coals studied were softer than their corresponding coarse sues while most of the remaining coals were uniformly hard in all sizes. A few coals contained fines which were harder than their coarser constituents. These variations in hardness give insight into the heterogeneous nature of coal.

Jan 1, 1968

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Christopher J. Bise

INTRODUCTION Face haulage in underground mines and pit haulage in surface mines are the principal domains of rubber- tired haulage vehicles. In underground mines, cable- reeled or battery-operated shuttle cars and diesel-powered load-haul-dump vehicles are used; trucks are primarily used in surface mines. Although many concerns go into the selection of rubber-tired haulage vehicles, such as clearance and tire life, the most important factor from a mine-planning standpoint is the production capability of the vehicle in the mine environment. Therefore, this chapter will address this topic. UNDERGROUND FACE-HAULAGE VEHICLES The selection process for underground face-haulage vehicles is, in some respects, much simpler than that of the other haulage systems discussed to this point. It is simpler because these vehicles, which transfer the mined material from the face to the intermediate haul¬age system, are manufactured in various size ranges to cope with the confinement of underground opening widths and heights. However, since these vehicles oper¬ated in an intermittent fashion in conjunction with a constantly advancing face, the system&apos;s lack of perma¬nence and overall dynamic nature create a more diffi¬cult situation for predicting productivity. The emphasis in this section will be on prediction of productivity. There are three fundamental steps that must be taken to analyze the productivity potential of any face¬haulage system: l) Recognize the geologic (seam thickness, etc. ) and mining (opening widths, etc.) constraints that affect the velocity/clearance aspects of the haulage equipment, and select equipment from manufacturers&apos; specifications with these con¬straints in mind. 2) Secure the elemental times of the face-haulage system. 3) Incorporate the elemental times into an accepta¬ble mine plan. By recognizing the geologic and mining constraints that affect the system layout, parameters, such as vehi¬cle payload, tonnage to be hauled per cut, and haulage distances, can easily be determined. Elemental times can be developed in two ways: 1) In an existing operation, a time study of the dynamic system can be conducted by placing three time-study engineers at the following static locations; (1) near the loading machine, (2) near the change-out point outby the face, and (3) near the dump. By synchronizing their watches and recording the actions of the haulage vehicles at these three locations, their time studies can be reduced to provide elemental times, such as vehicle tram rates (empty or loaded), vehicle discharge times, and loading rates. 2) In the absence of an existing operation, average values for the elemental times can be provided from other mines operating in similar condi¬tions, or by the manufacturers themselves.

Jan 1, 1986

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45&apos; to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;&apos; Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944