Search Documents

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

Water infiltration control techniques are designed to reduce the total volume of water entering an underground mine, and thus, reduce the volume of mine water discharge During the development of underground mines, water may be encountered in various quantities This water must be pumped from the mine during active mining, and in many situations, the weight of water removed will be more than the total weight of mineral extracted After abandonment of the mine, infiltrating water either floods the mine workings or discharges from the mine (27, 127) Infiltrating water may enter underground mines from above, below, or laterally through adjacent rock strata Earth fractures such as faults, joints, and roof fractures resulting from surface subsidence are commonly primary causes of water entrance Into abandoned underground mines Factors affecting the quantity of water entering a mine will be the depth of the mine, location of water bearing strata, and ground water flow patterns Investigations of the quantity of water entering underground coal mines have found the average rate of infiltration to range from approximately 6,262 to 10,280 liters per hectare per day (670 to 1,100 gal/acre/day) (27) Water flowing through underground mines flushes pollutants from the mine and may result in their discharge to the environment A reduction in the amount of flow usually results in a reduction in total pollution load discharging from the mine The techniques discussed in this section can be used to reduce the volume of surface and groundwater available to enter the mine system and transport pollutants The selection of a control technique will depend upon the characteristics of the mine system and the expected cost effectiveness of the technique In order for water infiltration control to be effective in controlling mine drainage pollution, the reduction in mine water flow must not be accompanied by an increase in concentration of pollutants (127) REFERENCES 2, 27, 51, 58, 127, 132

Jan 1, 1975

By Frederick Laist

ABOUT six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electro-negative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection-1 mg. or less per liter.

Jan 10, 1920

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. P. Polack

"INTRODUCTION The purpose of this circular is to correlate the information obtained during personal investigations at the sites of four rock tunnels in the process of construction and information obtained from the records and personal views of the constructors of two other tunnels that were not visited during the, excavation phase of construction and to present this information for the benefit of those who contemplate future construction of rock tunnels.Modern mechanized coal mining requires better, safer, properly alined haulageways and beltways; consequently, better understanding of tunneling methods by coal-mining men will be necessary. The possibility of future high-speed haulage systems utilizing rock tunnels in the more solid rock strata above or below the coal beds must not be discounted. In the past, tunnels have been driven for use in draining and unwatering inundated coal mines. At present, the need for such tunnels is very evident in some parts of the coal-mining regions, notably in the Pennsylvania anthracite fields, and studies along these lines are in progress. The average coal-mining man has little time or opportunity to visit tunnels while they are being exca-vated; therefore, it is hoped that this information will assist him in constructing tunnels safely if he is required to do so in the future.The tunnels described herein differ in size, shape, usage, and, in many instances, in their geological aspects. Full-face, heading and bench, and pilot-tunnel, and enlargement methods of excavation were utilized.The roof-support methods show diverse designs and materials of construction to suit each purpose and condition. The superiority of steel roof support over wood is demonstrated beyond doubt and is shown clearly in the photographs included in this circular.The illustrations (photographs taken by the U. S. Bureau of Mines, the U. S. Corps of Engineers, and others) show many of the necessary steps taken during the excavation and the erection of roof support in tunnels under construction."

May 1, 1950

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer's standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

By Phil Jones

"Dilution — planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a sixmonth period in fiscal year 2018 (FY18) that established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned versus actual toe data. These were rig alignment error, collar location change/ error and in-hole deviation.The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimizer system). The trials were undertaken in the same environment: the Cracow gold mine, an operating underground mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160 percent.The increased accuracy reduced stope dilution by reducing over-break of subgrade ore. The new technology was implemented at Cracow during the latter half of 2018. Despite utilizing the new technology for just six months of the year, the mine recorded a 5 percent overall reduction in dilution for the full year compared to the previous year (FY17); from 22 percent down to 17 percent (a net decrease of 22.7 percent). Mine management attribute a significant proportion of this reduction to the new technology, along with sequencing and planning improvements. This opinion is backed by detailed stope reconciliation data taken during the trial from 28 stopes — representing 20 percent of the total tonnes mined during FY18. The data identified that stopes drilled using the new technology recorded 62.6 percent less average dilution."

May 1, 2019

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1.935-36.3/ The present report covering 1,87 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. El Paso samples are reported with the South Rocky Mountain district, and. Amarillo, Tex., has teen included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated on table 1.

Jan 1, 1939

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability.The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employees to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed. IntroductionThis article is the second of three on predictive maintenance at the Louvicourt mine operated by Aur Resources Inc. The first article, published in the October 2002 issue, was about vibration analysis for rotating machines. This article describes how lubrication and oil analysis for stationary machines permitted Louvicourt to save more than $150,000 within two years and presents the evolution of the oil analysis program.Louvicourt mine, located near Val-d’Or, Quebec, is a copper and zinc mining and milling operation that processes 4300 t/d of ore and employs 289 people. Production began in 1994. Louvicourt mine is a partnership between Aur Ressources (30%), Teck Corp. (25%), and Novicourt (45%)."

Jan 1, 2003

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark&apos; makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter&apos; presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940