Search Documents

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By Michel Dupuy, Daniel Calais

The study of self-diffusion of plutonium in E phase has been carried out by the welded couples method. The tracer used was puZ4O which is detected by its X-ray emission (conversion lines of uranium which are computed between 13 and 21 kev). Intensities were measured with a scintillation counter. Each layer was removed in a direction parallel to the original interface with a grinding machine and a thickness measured with a pneumatic comparator. The concentration-penetration curves obtained were corrected for the effect of heating time from room temperature to annealing temperature and for the expansion due to phase transformations of plutonium. They were analyzed by the generalized Gruzin method. Self-diffusion of plutonium in E Phase is very fast cm per sec between 500" and 620°C) and the diffusion zones are 2 to 3 mm wide for annealing times ranging from 30 min up to 10 hr. The Arrhenius law gives the temperature dependence in the form: From the point of view of self-dqfusion, PUE phase falls into the anomalous bcc metals category (Tip , Hfp, Zrp, Uy) with a low-frequency factor and an activation energy lower than those provided by standard correlations. No theory proposed hitherto to explain these anomalies (influence of dislocations, of extrinsic vacancies bonded to inlpurities, of bi-vacancies) can clearly explain the self-diffusion coeffzcients of plutonium. DIFFUSION in bcc metals is a present-day problem. A recent symposium (Gatlinburg, 1964), followed by a book,' has been devoted to it. A great many experiments seem to show that diffusion in certain bcc metals obeys unexpected laws. The activation energies measured are sometimes strangely low (B hafnium, y uranium). For certain metals (0 zirconium, p titanium) the curves of log D (D = diffusion coefficient) as a function of 1/T (T = absolute temperature) are not linear. The frequency factors Do, which are of the order of 1 sq cm sec-' in fcc metals, vary from 1 to 10~6 sq cm sec-'. Various theories have been put forward to explain these anomalies; none is yet satisfactory. We wished to introduce a new experimental result by studying the self-diffusion in c plutonium. This allotropic phase, stable from 475°C up to the melting point (640°C), is in fact bcc. Unfortunately, nothing is known of the characteristics of the point defects in this phase, which limits the scope of the hypothesis which can be made about the mechanism(s) of self-diffusion in plutonium. 1) EXPERIMENTAL METHODS 1) Principle. We used the welded couple method. The two pellets of the couple initially have different 240 isotope contents (X emitter). After diffusion, the concentration/penetration curves are drawn up by the generalized Gruzin method. 2) Gamma Spectrography. The metal used in our study is plutonium, either low in puZ4O (isotopic content 1 pct) or high in puZ4O (8 pct). The latter also contains plutonium 241 (-1 pct) and 300 ppm of ameri-cium produced by the reaction Pu2U-AmM1 + 8-. The emission spectra of these two plutoniums placed in leak-tight vinyl bags have been studied by y spectrograph~. The detector is a thin crystal of thallium-doped sodium iodide. The activity of the plutonium rich in 240 is about twice that of the plutonium low in 240 in the energy band of 17 kev (L conversion lines of uranium); this band was used in these measurements. 3) Preparation and Examination of the Diffusion Couples. Diffusion couples were made from plutonium with a high and low PU"' content. Pellets (6 6 mm. thickness 3 mm) mounted on a polishing disc with ground parallel faces were polished mechanically on both sides. In this way, pellets with two parallel faces were easily obtained. The polished pellets were joined by a 6 phase anneal (420°C, 1 hr) in a small screw press (pressure of 20 kg per sq mm cold); a centering ring enabled the two pellets to be pressed coaxially. The couples then were subjected to the diffusion treatment by annealing in the E phase in sealed silica ampules in argon at atmospheric pressure. The annealing temperatures and times are given in Table I. The couples were encased in a mild steel ring, the joint interface being thus parallel to the ground face of the ring. The diffusion couple/ring assembly underwent successive abrasions by means of a magnetic plate grinder. The thickness of the abraded layer was measured with a Solex pneumatic comparator when it was less than 0.1 mm (accuracy 0.2 p) or with a mechanical micrometer (accuracy 3 p) for passes of the order of 0.2 mm. All these operations were done in glove boxes, as plutonium is particularly toxic. After each abrasion we determined the emission spectrum of the ground face. The emissive surface is defined by means of a diaphragm 3 mm in diam. We noted more particularly the X activity in the 17-kev

Jan 1, 1969

By H. A. Bourne, E. L. Haden, D. R. Reichmuth

A circumferential-toothed bit with novel tooth form gave improved penetration performance. In this design the exterior flank of all teeth were vertical when in rolling contact with the hole bottom. Rock chips were generated by the interior flank of the tooth displacing the rock inwardly and downslope toward the center of the hole. A unique two-cone laboratory bit assembly enabled evaluation of numerous cone and tooth configurations. Some of the variables investigated, in addition to weight on bit, rotary speed and rock type, were tooth interference, percent tooth, hole bottom angle, attack angle and relief angle. Most tests were conducted dry on a brittle synthetic sandsone or a ductile quarried limestone. Tooth configurations were found to be more significant in the ductile material. This was attributed to the deeper tooth penetration before rock failure. These studies showed that the attack angle (angle beween interior flank of the tooth and rock surface) was the controlling variable; changing the tooth configuration from the assymetric or semi-wedge to the more conventional symmetric or wedge form reduced penetration performance; and penetration performance of circumferential-type cutters was directly proportional to rotary speeds up to 200 rpm. INTRODUCTION Much of the published literature on rock-chisel interactions describe experiments wherein symmetrical wedges are vertically loaded or impacted against a smooth rock surface.1-6 are is usually taken to insure that the indentation is not made near the edge of the rock specimen less erroneous data be obtained. The literature describes relatively few studies in which the investigator deliberately attempted to take advantage of an edge or free surface. In contrast, anyone who chips ice or breaks up a concrete sidewalk almost always works near an edge. Chisel "indexing," which has been considered by some investigator1,2,6,7 makes limited application of an edge or free surface. Probably the best documented investigation into applying this idea to drilling was that of Drilling Research Inc. at Battelle Memorial Institute.' Their "annular wing" percussion bit consisted of paired asymmetric chisels oriented so as to produce and move chips to the center of the hole. They predicted that the lowest energy requirement for chip generation would be achieved with a stepped hole bottom having a median angle of 45" to the horizontal. Results from limited tests showed that approximately 50 percent of the rock fragments were large and semi-circular in shape, as would be expected by a chisel impact near an edge. The remaining 50 percent were fine chips produced by the chisels in re-establishing the steps or ledges. Initial penetration rates with this bit were high, but they rapidly decreased. This was the result of excessive tooth wear caused by the constant friction on the gauge surfaces. The basic idea — circumferentially placed asymmetric chisels — still appears to have merit. If the concept could be applied to a rolling cutter bit, two of the shortcomings of the fixed chisel design could be overcome: (1) reduction in tooth friction, and (2) greatly increased cutter surface. Adapting asymmetric chisels to cutters rolling on an inclined hole bottom is restricted by bit geometry. The basic elements of roller rock-bit construction prevents the practical attainment of a 45" hole bottom angle. Nonetheless, experimentally it was considered desirable to investigate the influence of hole bottom angle to at least 40". This paper describes the laboratory studies conducted in evaluating the circumferential-toothed roller cutter rock bit. EXPERIMENTAL APPARATUS AND PROCEDURE BIT ASSEMBLY The cost of constructing a sufficient number of conventional three-cone rock bits to investigate circumferential cutter performance was prohibitive. Instead, a novel two-cone laboratory assembly which used an external bearing system was designed and constructed. The external bearings made it possible to alter the journal bearing angles and thus allow a wide flexibility in cutter configuration. Fig. 1 shows the laboratory bit assembly, the various bearing mount plates and the appropriate roller cutters for drilling shallow holes having hole bottom angles of 0, 10, 20, 30 or 40". The bit was limited to a drilling depth of 1 1/2 in. at the gauge teeth and a hole diameter of 43/4 in. This more or less intermediate size bit was chosen because it gave a more realistic match between bit teeth and the rock than would a microbit. Also, the rock sample size required was convenient and easy to obtain. CIRCUMFERENTIAL CUTTERS The tooth configuration used in our initial studies is shown in the upper half of Fig. 2. All cutters used in this series had the same tooth form — 43" included tooth angle, 2" positive relief angle and a horizontal tooth flat width of 1/32 in. Each cone cuts alternate rows except for the gauge row. The row-to-row spacing in view was 1/4 in. Static loading tests conducted earlier with asymmetrical chisels had been used to establish this spacing. These tests showed energy requirements for chip production increasing rapidly as the distances to the edge increased beyond

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.' Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955

By Niels Hansen

The substructure formed by drawing at room temperature in aluminum (99.5 and 99.998 pct purity) and in recrystallized aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum -oxide was examined by transmission electron microscopy, and the flow stress of the drawn materials was measured by tensile testing at room temperature. A sub-grain structure was present after a reduction in area by drawing of 10 to 20 pct, and the subgrain size was observed to decrease with increasing deformation. The tensile data show that the increase in flow stress (0.2 pct offset) by drawing from 10 to 95 pct depends on the reduction in area, not on the composition of the materials. Dispersion strengthening and subgrain bowzdary strengtlzening contribute to the flow stress, and these strengthening processes have been found to be linearly additive. The flow stress (0) can be related to the subgrain size &) by the Petclz relation = uo + k . t, where go is dependent on the composition of the products and k is approximately the same far all materials. THE microstructure of dispersion-strengthened aluminum aluminum-oxide products consists of small oxide plates distributed in an aluminum matrix. The matrix structure depends on the manufacturing history, and in hot-worked as well as cold-worked products the matrix is divided by subgrain (or dislocation) boundaries. For hot-extruded products it has been shown1 that dispersion strengthening and subgrain boundary strengthening are linearly additive, and the flow stress (0.2 pct offset.) at room temperature has been related to the subgrain size (ts) by a Petch equation,2,3 s = so + k . ts-1/2, where s0, increases with increasing oxide content. For cold-worked products containing subgrains no systematic work has been reported, and it was the aim of the present study to examine the microstructure and the relationship between the flow stress and the subgrain size for such products. The behavior of' aluminum aluminum-oxide products depends on the purity of the aluminum matrix, and aluminum of the matrix purity (99.5 pct) was included in the investigation. The literature contains few data about the behavior of this impure aluminum, and aluminum of a higher purity (99.998 pct) was therefore also examined. As regards the relationship between the flow stress and the subgrain size in cold-worked dispersion-strengthened products, no systematic work has been reported. For aged cold-worked structures containing fine precipitates (Fe-Mo carbide) a Petch relation has been found,4 and it has been shown that the k value NlELS HANSEN is Head, Metallurgy Department, Danish Atomic Energy Commission, Research Establishment Riso, Denmark. Manuscriot submitted January 9, 1969. IMD is approximately the same as in iron, whereas the s0 value is higher owing to the presence of the precipi-tates. Investigations of metals such as tungsten,' ferrous metals,4,6 and molybdenum7 cold drawn or swaged at room temperature have shown that the flow stress can be related to the subgrain size by a Petch relation when ts is taken as the subgrain size perpendicular to the direction of deformation. For aluminum no work has been reported on the relationship between the flow stress and the subgrain size after deformation at room temperature, whereas for aluminum tensile strained at different temperatures in the range -183" to 375°C a Petch relation has been found by taking ts equal to the subgrain size.' In the present study two aluminum materials (99.998 and 99.5 pct) and three aluminum aluminum-oxide products (containing 0.2, 1.0, and 4.7 wt pct oxide) were drawn at room temperature to reductions in area from about 10 to about 95 pct. The structures were studied by transmission electron microscopy, and the flow stress (0.2 pct offset) was measured at room temperature. EXPERIMENTAL Materials. The materials are given in Table I together with the chemical analysis. The three aluminum aluminum-oxide products were manufactured from aluminum powder that had been compacted and Table I. Chemical Analysis of Materials Al203 Fe SI Material wt pct wt pct wt pct 99.998 pct* - 0.0004 0.0012 Aluminum 99.5 pctt - 0.36 0.16 Aluminum AlMD13† 0.2 0.16 0.12 Aluminum- -Oxide AlMD105† 1.0 0.26 0.18 Products SAPISML960s† 4.7 0.22 0.19 *Other impurities: O.0004 pct max each of Cu and Zn (supplier's analysis). †Other impurities: 0.03 pct max Cu. 0.02 pct max each of Mn, Mg, Zn, Ti. Table 11. Mean Diameter of Aluminum-Oxide Particles in Extruded and in Cold--Drawn Aluminum Aluminum-Oxide Products Mean Diam. of A1203-Plates* Material State A AlMD105 Extruded 540 Cold Drawn 97 pct 510 SAP ISML 960 Extruded 770 Cold Drawn 95 pct 820 *The standard deviation of the mean is approx. 5 ±pct.

Jan 1, 1970

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952

By J. Weijdema, D. N. Dietz

In the conventional underground combustion process (dry combustion) much heat is left behind in the swept formation and goes to rva.rte. Econonmy can be improved by heat recuperation through water injection. This is most advantageous if done at the earliest opportunity before much heat is dissiputed to cap and base rock. Water injected simultaneously with the air will flash to superheated steam, which passes through the combustion front together with the nitrogen from the air. A condensation front traveling up to three times as fast as the combustion front drives out the oil. In this type of wet combustion, the water evaporates before it reaches the combustion zone. The evaporation front travels more slowly than the combustion zone. If so much water is injected that the evaporation front overrun the combustion front, combustion in that spot will be quenched and some unburned fuel will be left behind. Air reacts with the oil farther down-stream where steam temperatures occur; at steam temperature, the air reacts rapidly with the oil. Velocity of the combustion front is increased thereby and is governed essentially by the water-injection rate. In the extreme case of high water-injection rate, a short heat wave of constant length is driven through the formation by water injection. Once this wave has been established, no more heat need be generated than that required to make up the heat losses from the short heat wave; a relatively low rate of air injection will suffice. The feasibility of partially quenched combustion has been confirmed in tube experiments. A heat wave at steam temperature is observed. Chemical analyses of flue gas indicate preferential burning of hydrogen while a carbonaceous residue is left in the formation. Introduction A disadvantage of so-called dry in situ combustion is that air-compression costs are rather high. An air consumption of about 400 std cu m/cu m (400 scf/cu ft) of formation swept is an accepted figure. This high consumption is mostly wasted since much heat is left behind in the depleted oil sand. Methods were investigated for recuperating as much as possible of the heat left behind. This paper deals only with basic principles and is confined mainly to one-dimen- sional flow without lateral heat losses; experiments were conducted in relatively narrow, well insulated tubes. If some water is injected with the air, it will turn to superheated steam in an evaporation front, which should travel behind the combustion front. The steam having passed the combustion front causes a steam drive by a condensation front that can travel faster than the combustion front. The latter needs to travel only part of the distance covered by the oil-displacing condensation front, and thus consumes less air. The water-air ratio would seem limited to that at which cold water overruns the combustion. This limitation was deliberately exceeded considerably in theory and experiments. It was found that combustion is then indeed quenched, but only locally. Farther downstream, the oxygen finds residual oil at steam temperature, which is suficiently high to ensure rapid oxidation. Thus, the combustion front uses only part of the available fuel because it is chased through the formation faster than its normal velocity. No heat is left behind. This new process is called "partially quenched combustion". At the upper limit of the water-air ratio, a small heat slug is moved through the formation by the flow of water and steam. Only a small flow of air is needed since it has only to generate sufficient heat to make up for the lateral heat losses of the short heat slug. Theory Although many factors complicate underground combustion, the processes will be presented in their simplest form. For this reason, one-dimensional flow without lateral heat losses is assumed. Heat conduction in the direction of flow also is disregarded. Under these conditions, dry combustion causes very high temperatures. The heat-carrying capacity of the gas stream is small. Heat generated by oxidation of a residual oil saturation is retained in the sand. The available fuel determines the air requirement and the temperature obtained. Accepting the often-mentioned air consumption of 400 std cu m/cu m (400 scf/cu ft) formation, we calculate a temperature of the swept sand of 1,200C (2,192F) (Fig, I). If water is injected at a modest rate with the air, it will flash to superheated steam upon contact with the heated sand. One cu m (35.31 cu ft) of hot formation will evaporate about 0.5 cu m (17.66 cu ft) of water, and thereafter will accommodate (at an estimated 0.80 saturation and an assumed 0.40 porosity) another 0.3 cu m (10.59 cu ft) of water in cold condition. As long as less than 0.5 + 0.3 = 0.8 cu m (28.25 cu ft) of water is injected for every 400 std cu m (14,125 scf) of air (water-

Jan 1, 1969

By P. Chiotti, G. R. Kilp

Thermal, metallographic, vapor pressure, and X-ray data were obtained to establish the phase diagram for the zinc-zzrconiz~m system. Five compounds corresponding to the stoi-chiometric formulas ZrZn, ZrZn,, ZrZn,, ZrZn,, and ZrZn14 were observed. All these compounds, with the exception of ZrZn2, which melts congruently at 1180°C under constrained zinc-vapor conditions, undergo pexitectic reactians. The temperature at which the zinc vapor pressure is I atm for a series of alloys was determined from vapor-pressure measurements. The data obtained are summarized in the construction of a I-atm-pressure phase diagram and a phase diagram corresponding to a pressure of less than 10 atm. THE purpose of this investigation was to establish the phase diagram for the zinc-zirconium system. Thermal, metallographic, vapor pressure, and X-ray data were employed in determining the phase regions. Partial investigations of this system have been conducted by Gebhardt1 and Carlson and Borders.' Carlson and Borders studied the high-zirconium region and established the existence of a eutectic at 69 wt pct Zr with a melting point of 1015°C. The terminal phases of the eutectic horizontal were shown to be an intermetallic compound ZrZn and a solid solution of ß zirconium containing 21 wt pct Zn. The ß solid solution decomposes into ZrZn and a zirconium at 750°C. The eutectoid composition is given as 15 wt pct Zn, and the solubility of zinc in a zirconium at temperatures below 750°C is indicated to be negligible. Gebhardt studied the zinc-rich region and observed a lowering of the melting point of zinc from 419.5" to 416°C and temperature horizontals at 545" and970°C. Some preliminary observations by Chiotti, Ratliff, and Kilp were reported by Hayes.2 pietrokowsky3 has reported the compound ZrZn2 to have a cubic MgCu2 structure with ao = 7.396A. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc or Baker analyzed reagent granulated zinc, both 99.99 pct pure and hafnium-free iodide-process crystal bar zirconium obtained from the Westinghouse Electric Corp. The zirconium contained 200 ppm Fe, 200 ppm Si, 100 ppm C, and minor amounts of other impurities. The zirconium was milled or machined into thin chips or shavings. These were cleaned with a nitric-hydrofluoric acid solution, rinsed with water, and acetone, and dried just prior to their use in alloy preparation. The granulated zinc was similarly cleaned using dilute nitric or hydrochloric acid. Weighed quantities of these materials, 20 to 30 g total, were mixed and pressed at 20,000 to 70,000 psi to give relatively dense compacts. During the early part of this investigation the pressed compacts were placed in MgO-15 wt pct MgF, crucibles which were then sealed inside of quartz ampules. The compacts were given various prolonged heat treatments prior to their use for thermal analyses, or vapor-pressure measurements. Because of expansion of the compacts and the relatively high zinc vapor pressure it was difficult to heat to the melting temperatures of the alloys without failure of the quartz ampules. Homogenization at temperatures below the melting temperature gave brittle, porous alloys unsuitable for metallographic examination. It was also difficult to prevent condensation and segregation of zinc on the colder parts of the quartz ampules during heating and cooling operations. These problems were eliminated to a great extent by the use of tantalum crucibles. Tantalum proved to be a satisfactory container with little or no reaction between the alloys and the tantalum. Small tantalum thermocouple wells were successfully welded in the bottom of these crucibles. Pressed compacts were sealed inside the tantalum crucibles by welding on preformed caps under an argon atmosphere. Heat treating and differential thermal analysis were combined into a single operation. The experimental sample assembly is shown in Fig. 1. This assembly was enclosed inside a stainless-steel tube heating chamber which could be evacuated and filled with an inert gas. The thermocouple leads were brought out of the heating chamber between two rubber gaskets used to provide a vacuum seal for the water-cooled head. Most of the compounds in this system undergo peritectic decomposition. After heating above the temperature of a particular peritectic horizontal the sample was cooled to just below the peritectic temperature and held at temperature for several hours. The sample was then reheated through the peritectic temperature and the size of the thermal arrest, if still present, compared with the one previously obtained. If the thermal arrest was not characteristic for the alloy composition being investigated its magnitude diminished and repeated cycling and annealing eventually eliminated it. The peritectic thermal arrests characteristic of a particular composition were established in this manner.

Jan 1, 1960

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.'s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.' P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,' R. T. Hukki,' D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.'s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott's western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott's Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per 'C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons' interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3' All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.'s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.'s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967

By W. F. Campbell

One of the deepest coal operations today is the Springhill No. 2 mine of Cumberland Railway & Coal Co., subsidiary of Dominion Coal Co. Ltd. Mining is now conducted at a slope distance of 14,000 ft, with 4400 vertical ft of cover. The record of Springhill No. 2 can be said to contain the history of bumps in the Province of Nova Scotia. The Springhill coal field forms part of the Cumberland field of Carboniferous age. There are seven mineable fields in the area, numbered in the order they were discovered. Mining has been carried on in all but the No. 4 and 5 seams, but present operations are confined to the No. 2. Fig. 1 shows a vertical section through the seams. Opened in 1873, No. 2 mine was first worked from parallel slopes driven from the outcrop of No. 2 seam down to the 7700 level. As the mine went deeper, a two-place auxiliary slope was driven from the 6900 level to the present workings. A transfer level at the 7800 connects the main haulage with the auxiliary haulage slope. The No. 2 mine plan is shown in Figs. 2 and 3. The seam is bituminous, averaging 8.5 to 9 ft thick. There is a well defined parting 14 to 16 in. from the roof, and this roof coal is harder than the rest of the seam. Average pitch at the outcrop is 30°; at the 6500 level, 20°; at the 7900 level, 16°; and at the 13,800 level, 10°. Immediate roof and floor strata consist of beds of variable thicknesses of shales, grading to arenaceous shales to shaly sandstones to sandstones. A characteristic of the strata is the appearance and disappearance of sandstone bands, of considerable thickness, over distances of several hundred feet. MINE HISTORY Entrance to No. 2 mine is obtained by three parallel slopes, separated by 100-ft pillars except in the upper portion of the mine where the pillars are smaller. Main haulage levels were originally driven 600 ft apart for room and pillar extraction. A parallel drainage and intake airway was driven below each haulage level and a parallel return airway (counter level) above. Pillars 80 to 100 ft wide separated these two servicing entries from the center haulage level. Inclines up to 700 ft apart were driven off the levels up pitch to the upper levels, and at 40-ft centers level rooms 12 ft wide were driven off each side of the inclines, separated by crosscuts every 50 to 100 ft. The rooms were driven up to 350 ft or until they were holed into the room from the adjoining incline—a plan followed until the level reached its boundary. When the entire area between two levels had been divided into pillars, the pillars were extracted from the boundary back to the slope pillars. As depth of cover increased, mining conditions required larger pillars, and at the 3300 level, where NECESSARY PRECAUTIONS FOR MINING AT DEPTH In Room and Pillar Extraction: 1) Pillars must not be too small. 2) Pillar size must be uniform. 3) Extraction lines must be kept as straight and as uniform as possible. If they are irregular they should be brought back into line slowly. 4) Peninsulas of coal surrounded by gob must be avoided. 5) Pillars should not be disturbed after they have been formed. If it is necessary to increase the width of an opening, stripping or ribbing should be done gradually over a long distance. If increased width of openings is necessary at certain locations and can be anticipated, the openings should be widened during development. 6) Under no conditions should small pillars be left in the gob that would interfere with caving. In Long wall Operations: 1) Pillars formed during development for retreating longwalls should be uniform in size and shape. 2) Pillars should not be split after development, but if pillar splitting does become necessary it should not be carried out within the zone influenced by the working faces. 3) Width of levels should not be increased after the levels have been developed. If it does become necessary to widen a level it must be done gradually over a long distance by stripping or ribbing the coal ribs. 4) Extraction lines should remain uniform. If several walls are worked together—one behind the other—a uniform distance must be maintained between them and the wall faces must be kept as straight as possible. If the walls do get out of line, they must be brought back into line gradually to allow for a gradual change in the stress distribution over the area. 5) Stumps of coal, roof supports, etc. must not be allowed to remain in the gob to interfere with caving. 6) Midwalls should be built as rigidly as possible and properly maintained.

Jan 1, 1959

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.' The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of ' However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-' have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h') formed by the reaction where, accorhng to the notation of Kroger and Vink,6'7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i' and Fe3' ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.'-' A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i' and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965

By Fuming Wang, Changrong Li, Dan Wu, Wei Shen, Yaxu Zheng

In order to improve the oxidation resistance of Cr–Mo–V steel for high-speed railway brake discs, a higher Cr was added to the steel. Effect of temperature on the oxidation behavior of brake disc steel with different Cr contents was studied by OM, SEM and XRD. The results show that the oxidation curves at 500 °C obey a linear oxidation law in 0–2 h and 2–20 h, respectively. The oxide layer is thin and the oxidation products are Fe2O3 and Fe3O4. The oxidation curve at 700 °C follows a linear law within 2 h. With the oxidation time extending, the oxidation curves follow a parabolic law and the oxide layer becomes thicker. Moreover, the oxide layer is divided into two layers. The outer oxide layer is loose and is mainly Fe2O3, while the inner layer is denser and consists of FeO and FeCr2O4. The oxide layer thickness reduces and the oxidation resistance of the steel is improved with Cr content is increased.

Mar 1, 2018

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By William S. Springer

A NEW preparation plant has been put in - operation to treat coal from the recently opened Concord mine, located about 15 miles west of Birmingham, Ala., by the Tennessee Coal, Iron & Railroad Co., a U. S. Steel subsidiary. The mine produces metallurgical grade coking coal from the American seam for use as coke in the company's blast furnaces at the Fairfield and Enseley works. The capacity of the operation is 1000 tons of run-of-mine per hr, approximately half of which is delivered to the by-product coke plant at Fairfield after beneficiation to metallurgical grade. The remaining portion of the mine run is rock and refuse removed during preparation. No boiler coal or other fuels are produced by this mine. Preparation of the coal is done both under- ground and on the surface. The underground primary crushing station removes some tramp iron, and screens and crushes the oversize, most of which is rock, to protect the main slope conveyor. The surface plant consists of a crushing and screening plant, large blending bins, a two- process washing plant, a water clarification and

Jan 1, 1950