Search Documents

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By Staia. Mariana H.

Thermochemical equilibria of the heterogeneous system Ti-N-H-CI-Fe-Cr-Mo-Ni-Mn-C were calculated by using a commercial software based on the minimization of the free energy. Equilibrium calculations were done for temperatures varying between 800" and l 100°C and an initial molar relationship between reactants, a=NJTiCI,, of 0.1 to 2. The deposition process was considered to occur at atmospheric pressure. The activities of the alloying elements of the stainless steel were considered equal to their molar fractions. It was shown that for the conditions studied the substrate is no inert with respect to the gaseous phase. The existence of liquid chlorides was predicted for temperatures between 800" and 850°C and a ratio between 0.3 and 0.9. The most important metallic chlorides which appears to be present from the calculations in appreciable quantities in the gaseous phase are iron dichloride and manganese dichloride. In the low-temperatures zone and for low initial nitrogen contents, it result that the appearance of the liquid chlorides seems that partially inhibits the production of gaseous HCI. The highest deposition process efficiency calculated is obtained at a temperature 2 900°C and a N2/TiCI, ratios 2 0.7.

Jan 1, 1995

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By J. A. Herbst

Until the past decade, the energy-size reduction relationship was the dominant form of mathematical model used in the description of tumbling mill grinding processes (1,2). Typically, in these models some single measure of product fineness (e.g. the 80% passing size, the size modules, the specific surface area) is chosen as the dependent variable and the energy input per unit mass of material being ground acts as the independent variable. In some instances these models have been useful for the correlation of experimental data, but, invariably, they have been found to be inadequate for meaningful process simulation. During the last decade considerable advances have been made in the development of phenomenological grinding models derived from population balance considerations (3-7). In these models a set of dependent variables is employed, corresponding to the set of mass fractions which constitute the product size distribution, and energy input is abandoned in favor of "time in the mill" as the independent variable. The phenomenological models have been shown to provide accurate simulations of the entire size distribution of ground products produced in batch (8-10), locked cycle(11)and steady and unsteady state, open and closed circuit continuous grinding(12,13).

Jan 1, 1973

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959

By Roy L. Wilfong, LeRoy R. Furlong, Louis P. Domingues

The bulk and apparent densities , particle size , and surface area of ceria powders derived from the ammonium sulfate , carbonate , nitrate , oxalate , and sulfate salts and heated at 950 ° to 1,500 ° C for 1 to 24 hours were studied . The bulk and apparent densities and particle size generally increased , and surface area decreased with increase in temperature and time of heating ; surface area was more sensitive to changes in temperature and time than the other properties studied . These properties of the ceria powders had a marked dependence on temperature and a lesser dependence on duration of heating at a given temperature ; and the source of oxide and thermal treatment cannot be considered optional in the preparation of refractory powders by thermal decomposition . The ammonium sulfate and sulfate salts heated at 950 ° and 1,200 ° C produced oxide powders with the lowest bulk density , the smallest particle size , and the highest surface area . The highest apparent densities were achieved for oxides resulting from the carbonate and the sulfate but the carbonate - derived material was considerably coarser . The surface areas of ceria powders derived from cerium salts decrease in the order of sulfate , ammonium sulfate , nitrate , oxalate , and carbonate . The observation of these physical properties are useful in predicting the sintering behavior of various oxide powders .

Jan 1, 1964

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

By C. E. Corson

THE experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to have received less study and description from the standpoint of the metallographist than many others. The investigation here described was directed to the following points:-Steel containing about 0.50 per cent, of carbon : 1. The structure as related to the temperature, at the same rate of cooling; 3. The structure and physical properties as related to temperature at different rates of cooling; 3. The structure and physical properties as related to different finishing-temperatures and different rates of cooling; 4. The bearing of these observations upon the statement of Prof. Albert Sauveur.1

Sep 1, 1906

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By John R. Lotz

DEVELOPMENTS in Iran currently arousing interest in a considerable portion of the world, particularly on the part. of that country's immediate neighbor on the North and in our own country, an inseparably related to and largely dependent upon the government's attempts to strengthen its economy and improve the standard of living of its people. These efforts are encompassed by provisions of the Seven-Year Development Plan recently enacted and not, in the process of implementation. It is a fine example of what one financially sound but extremely backward and poorly equipped country has undertaken to do on its own account and with its own resources. This Seven-Year Plnil was formally authoriztld by an act of the Iranian Parliament in February 1948. Its stated objects are to carry out such plans for the development of the country and its economy as ail1 raise the standard of livinc: and standard of education of the people, and re- duce the cost of living. A seven-yrar program for carrying out the work within the limits of appropriations was assigned under the law. The total amount to be expended during the seven- year period was fixed at the equivalent of $670 millioil at current rates of exchange.

Jan 1, 1950

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By J. Kang

Large-scale land reclamation has been undertaken in Singapore since the 1960s. In the early years, the fill materials excavated from the hills. In recent years, sea sand is the main source of the fill materials. The contractors used to import the sea sand from the neighbouring countries such as Indonesia. However, in early 2000, the sea sand import from Indonesia and Malaysia was banned. Cambodia, Myanmar, and Philippine therefore became the alternative sources for sea sand. Distance between the jobsite and these countries is over 1,200 km, and transporting sea sand from these areas became a critical issue that could affect the contractor?s performance. Figuring out the right combination of transportation means for a longdistance sand transportation would be challenging because of uncertain situations. We developed a stochastic simulation model, using ARENA, to figure out the right quantity of small-size barges, bulk carriers, and loading/unloading equipment, which could help project managers yield the most production for sand transportation. This paper presents how we developed the simulation model, how it was applied to figure out the optimum combination among various size barges, different bulk carriers, and various types of loading/unloading equipment, for the sand transportation project in Singapore.

Aug 1, 2013

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By A. Steiner, K. L. Komarek

Activities of aluminum in solid Ni-A1 alloys have been determined between 20 and 60 at. pet Al and 1200" and 1400°K by an isopiestic method in which nickel specimens, heated in a temperature gradient, are equilibrated with aluminum vabor in a closed all-alumina system. The activity of aluminum shows a strong negative deviation from Raoult's law at low concentrations but increases by three orders of magnitude within the ß(NiAl) phase. The partial molar enthalpy and entropy of mixing are negative. Using Wagner and Schottky's theory of ordered compounds, a degree of disorder of 4 x 10 -4 for NiAl and 1.25 X 10-2 for FeAl has been calculated THE Ni-A1 system has been studied by a great number of investigators, and the results, as far as the phase diagram is concerned, have been compiled by Hansen.1 The phase boundaries from 0 to 50 at. pet Ni are well-established. At higher nickel contents the boundaries are still in dispute and an additional phase, A12Ni3, has been reported.' The phase diagram is dominated by a very stable high-melting compound, NiA1, with a relatively wide range of homogeneity. Heats of formation of solid alloys have been determined calorimetrically by Oelsen and Middel3 from 20 to 95 at. pet Ni and by Kubaschewski4 from 25 to 80 at. pet Ni. According to the most recent compilation5 no other thermodynamic investigations have been reported for the Ni-A1 system. Due to the corrosive nature and the low vapor pressure of aluminum, a method has been employed for determining activities of aluminum which was previously developed for the Fe-A1 system.= Nickel specimens, heated in a closed evacuated alumina system in a temperature gradient, were equilibrated with aluminum vapor from a source within the system kept at constant temperature. After complete equilibration the specimens were analyzed and activities calculated from the known vapor pressure of aluminum. APPARATUS AND EXPERIMENTAL PROCEDURE Materials. The nickel specimens were made from wafers of electrolytic nickel (International Nickel Corp.) of 99.99 pet purity which were rolled to a 0.001-in.-thick foil by Driver-Harris Co. and to a 0.005-in.-thick sheet in our laboratory. The aluminum (Aluminum Corp. of America) had a purity of 99.99+ pct. The alumina tubes and crucibles were made of impervious recrystallized alumina with an alumina content of 99.7 pet (Triangle RR, Mor-ganite Inc.). Experimental Procedure. Annular specimens were punched from the sheet, the punching burrs removed, and the specimens degreased in carbon tetrachloride and acetone and weighed on a micro-balance to within an accuracy of ±0.01 mg. The specimens were positioned with alumina spacers along an alumina tube, and the positions measured. Aluminum metal was machined into cylindrical shape, and placed into an alumina crucible. The tube with the specimens was then inserted into a hole drilled into the aluminum metal. An alumina tube with its closed end at the top was slipped over the specimens so that its lower end fitted snugly into the alumina crucible. The assembled reaction tube was inserted into a mullite tube with a water-cooled brass head which had an opening for a quartz thermocouple protection tube and a metal-to-glass connection to a conventional vacuum system. A Pt-Pt 10 pet Rh thermocouple could be raised and lowered in the quartz tube which was placed along the outside of the alumina reaction tube. The mullite tube was heated by two separately controlled resistance-tube furnaces so that in the experimental temperature range an over-all temperature gradient of approximately 150o to 250°C could be imposed on the reaction tube. The position of the mullite tube was adjusted so that the surface of the aluminum metal was always at the temperature minimum. The reaction tube was thoroughly evacuated before and during slowly heating the assembly up to the melting point of aluminum. A pressure of less than 2 µ (Hg) was maintained during an experiment. Once the aluminum had melted, it isolated the contents of the alumina tube from the surroundings. Several times during an experiment the temperature gradient was carefully measured. An experiment lasted from 3 to 6 weeks and it was terminated by air cooling the evacuated mullite tube. For further details of the experimental procedure the paper on the Fe-A1 system6 should be consulted.

Jan 1, 1964

By Luc Delaey, Horace Pops

The structure and morphology of thermoelastic and burst type martensitic phases that form upon cooling in Cu-Zn-Si p phase alloys have been studied by transmission electron microscopy. The martensitic phases are composed of a lamellar mixture of two close-packed structures with different stacking sequence, namely ABCBCACAB (orthorhombic) and ABC (fcc). Striations within thermoelastic martensite are most likely produced during interaction with impinging burst-type martensite and not as a consequence of secondary shears. In a study of the martensitic transformation in ternary Cu-Zn based 0 phase alloys1 the dependence of the martensitic transformation temperature, M,, with composition shows variations for elements within a constant valence subgroup and between different subgroups. Such variations are not reflected in a change in habit plane, which is approximately the same for each ternary alloy, namely in the vicinity of (2, 11, 12 Ip. The fact that the habit plane remained constant, despite large differences in M, temperature and electron concentration, suggested2 that the crystal structures of the martensitic phases could be nearly the same. Crystal structures of ternary Cu-Zn based martensites have been determined recently for alloys containing the three-valent elements gallium3, 4 and aluminm. The present studies have been made to examine the structures and morphology of the martensitic phase in ternary Cu-Zn based alloys containing a four-valent element, silicon. I) PROCEDURE Two alloys were prepared by melting and casting weighed quantities of the component high-purity metals in sealed quartz tubes under half an atmosphere of argon. They were subsequently remelted by levitation under a protective atmosphere of argon. After allowing for losses of zinc as determined by the difference in weight before and after casting, the compositions in atomic percent of both alloys were established to be Cu-33.5 Zn-1.8 Si and Cu-27 Zn-5.0 Si. These alloys were homogenized in the P-phase field for 2 days at 800" C. Bulk samples consisted of a martensite phase at room temperature, the M, temperature being approximately 30' and 200" for the 1.8 and the 5 pct Si alloys, respectively. Thin disks were cut from the ingots using a spark machine, and they were heated for 5 min at 800' and quenched into water in order to obtain martensite. These slices were thinned chemically at room temperature in a solution consisting of 40 parts HN03, 50 part H3PO4, and 10 parts HC1 and thinned further electrolytically by the Window technique, using a voltage of 15 to 25 v and a mixture of 1 part HN03 and 2 parts methanol, which was kept at a temperature near -30° c. Foils were examined by transmission electron microscopy using a Philips EM 200 electron microscope. 11) RESULTS AND DISCUSSION 1) Structure and Morphology. Fig. 1 shows the martensitic phase in the alloy containing 1.8 at. pct Si. This phase is composed of contiguous platelets, each containing striations. The direction of the striations changes at the boundary between individual platelets. These internal markings resemble the striations that are usually identified as stacking faults, as for example in Cu-A1 martensites6-a or the lamellar mixture of two close-packed phases in Cu-Zn-Ga marten-sites.3p '9 lo In the present alloys, selected-area diffraction experiments have been obtained in order to determine the nature of the striations. Figs. 2(a), (61, and (c) are electron diffraction patterns of an area inside a single martensite plate. Fig. 2(a) contains diffraction spots which correspond to two close-packed structures with different stacking sequences, namely ABCBCACAB (orthorhombic) and ABC (fcc). Spots belonging only to the fcc structure are indicated by arrows. By tilting the foil either the orthorhombic structure, Fig. 2(b), or the cubic structure shown in Fig. 2(c) may be obtained. When the foil is oriented so that only the diffraction spots of the orthorhornbic structure are present, bright-field illumination shows small lamellae, as seen in Fig. 3. In this figure the lamellae that belong to the fcc structure are bright bands inside the dark extinction contours of the orthorhombic structure. The boundaries of the lamellae are parallel to the basal planes of the orthorhombic structure and to the {Ill} planes of the cubic structure, the close-packed directions of both structures being parallel. The 5 pct Si alloy shows similar features as those described for the 1.8 at. pct Si alloy.

Jan 1, 1969

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By C. E. Sims, F. W. Boulger, H. A. Saller

Most of the data on equilibrium constant and the deoxidations potentialities of those elements, considered to be stronger deoxidizers for steel than is silicon, have been calculated from thermodynamic data. The reason for this is, primarily, the obvious difficulty of obtaining direct experimental evidence of equivalent accuracy. This is an excellent use of the principles of thermodynamics and has given valuable data not otherwise available. Such results, of course, can be no more accurate than the physical constants used in the calculations, and one can never be sure that the basic data are either complete or accurate. In fact, as in the case with silicon,1 there are not only discrepancies among the calculated theoretical values of the equilibrium constant for deoxidation of steel but also between the theoretical and experimental values. It is highly desirable, therefore, to obtain experimental values for checks on calculated results whenever possible. If they disagree, both cannot be right, but if there is good agreement, their value is enhanced. The present work was done in an effort to obtain experimental evidence in regard to some of the common alloying additions but more particularly the so-called "strong" deoxidizers for steel. The method used was to determine the minimum concentration of the deoxidizer that would effect a certain definite degree of deoxidation in steel. The criterion of deoxidation was the change from the large globular Type I sulphide to the eutectic Type II as described by Sims and Dahle.2 This change is sharp and definite, and inasmuch as it can be produced with equal facility by aluminum, zirconium, and titanium, it is considered a manifestation of a certain degree of deoxidation and not an alloying effect. Ostensibly such a procedure could give only a comparison of deoxidizing powers and no absolute values. Nevertheless, repeated observations have shown that, when increasing increments of aluminum are added to a steel, the residual aluminum content begins to increase simultaneously with the appearance of Type II inclusions. Thus it seems warranted to postulate that the Type II inclusions appear coincident with the virtual elimination of FeO as an active constituent of the steel. Experimental Procedure The data obtained were primarily from the microexamination of polished and unetched specimens and from chemical analysis. Experimental heats weighing 200 to 250 lb were made in a basic-lined high-frequency induction furnace. The base composition was nominally that of a medium-carbon casting steel to which the appropriate additions were made. Specimens were poured into sand-cast ingots 3 in. in diam as shown in Fig 1. Sand-cast ingots were used to prevent chilling and to allow sufficient time in freezing for normal inclusions to form of a size large enough to be studied readily. In the first few heats, the tapered wall ingot was used, but in the majority, the extra large riser was used to prevent piping in heavily deoxidized steels. Specimens for microexamination were taken from the location shown in Fig 1, and drillings for chemical analysis were taken from a similar location. The procedure was to melt the base composition and deoxidize with the usual manganese and silicon additions and then to pour an ingot. The furnace was then tilted back, and the first increment of strong deoxidizer or special alloy was added and allowed to disseminate through the melt, with enough power on to hold the temperature constant, for 45 sec. Then a second ingot was poured. After this, another increment was added, and after the same holding time another ingot was poured. In this way from 9 to 12 ingots were poured from each heat, each successive ingot having progressively larger total additions of alloy. Eighteen heats were made altogether, and the range of alloys used and additions made are outlined in Table 1. The three principal types of sulphide inclusions found are illustrated in Fig 2. The globular Type I sulphides are characteristic of silicon-killed steels, the eutectic Type II are characteristic of steels deoxidized with a small amount of aluminum, while the larger, angular Type III are usually found in steels with a residual aluminum content above about 0.02 pct. In all specimens studied, the transition from Type I to II either did not occur at all or was very abrupt and clear cut. There never was any doubt as to just which increment produced the change, although the individual additions were small, in the order of 0.01 pct. The change from Type II to Type III was considerably less sharp, and, in some cases, both types were found together. Inasmuch as the formation of Type III sulphides is apparently not a deoxidation phenomenon, they will not be discussed here.

Jan 1, 1950