Search Documents

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By S. Narra, M. Nelles, I. Eickhoff, S. Teitge

"The aim of the research is to develop a holistic process flow for the recycling of glass fibres from glass reinforced plastics (GRP) and carbon fibres from carbon fibre reinforced plastics (CFRP), wherein the dissolution of the fibre epoxy resin matrix, separation of fibre fractions and their renewed material use is intended. In clear distinction to the previous research and development projects, the aim here is to recycle complex composite structures such as dismantled/disused wind turbine rotor blades and end-of-life composite wastes. In the course of the study, mechanical, hydrothermal and thermal processes and their combined procedures will be developed. As the fibre length is a decisive quality criterion in the recycling of composite materials, the further focus of the study will be the development of upstream and downstream material processing, in which the fibres are retained in their original form. The evaluation of the recycled fibres obtained is based on the elemental composition, measurement and morphological evaluation of individual filaments by scanning electron microscope (SEM), micro tensile tests on single fibres and their comparison to virgin fibres. The resulting process water is analysed by gas chromatography and mass spectroscopy (GC-MS) and a potential recirculation is determined. In cooperation with companies from the composite processing industry as well as recycling companies, a return of the recycled fibres to the known manufacturing process will be examined and an energetic and economic evaluation of the overall process will be carried out. Ambitious aim of the study is to achieve an actual recycling instead of the present downcycling or the energetic utilization. INTRODUCTION As global warming increases, so does the awareness of consumption and production of energy. To counteract the effects of global warming, renewable energy has been increasingly used during the last two decades, not only in Germany, but worldwide. Both, hydropower and wind energy, hereby play a fundamental role. After the end of their useful life of 20 to 30 years, the wind turbines (WTs) are being dismantled. Due to their foundations and tower segments, their recycling rate hereby exceeds 90% by mass. So far, the resulting rotor blade waste played a minor role accounting for only 2 - 3 weight-% of the total plant. Rotor blades of modern wind turbines are made of glass and carbon fibers, which are embedded in an epoxy or polyester resin matrix, balsa wood, PU or PET foams as fillers as well as various paints and coatings. These wastes currently end up in waste incineration or are sold to non-European countries."

Jan 1, 2018

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By C. J. Johnson, C. J. Bise

"IntroductionCoal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation· s deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only af1er ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental composition of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines.There are several potential contributions of this type of study to the coal mining industry. First after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies.Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location a mining company could predict anew mine's respirable dust elemental composition In the immediate ventilation return by using exploratory drill core samples of the roof ,coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved.Scope of workTo investigate the variability of the chemical characteristics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and mid western United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee ( 1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs."

Jan 1, 1989

By Ahmed Elmekati, Frederick C. Rhyner, Steven R. Lowe

"The current phase of the Pacific Park development (formerly, Atlantic Yards) in Brooklyn involves constructing buildings on a platform over an existing LIRR rail yard. To preserve the maximum amount of space in the already congested yard and protect the yard which remains in service during construction, high capacity foundations are being designed well above previous capacities in the area. In addition to spread footings and small mats, various diameters of drilled piles are being used at design capacities ranging up to 600 tons. The piles are generally grouted at low pressure, up to about 50 psi. Load tests for various drilled elements, including piles, tiedowns and soil anchors, have confirmed allowable side resistance (bond) stresses in dense sand ranging from 20 to 30 psi. Testing with different rigs and operators has shown that down-the-hole hammers are feasible, but the installation techniques, types of equipment and size of the pile make a significant difference. The results show that more cost-effective foundations are possible when ample testing confirms expectations.I INTRODUCTIONThe Long Island Rail Road has operated a mainline on Atlantic Avenue since the 1800s, with a terminal at the intersection of Atlantic and Flatbush Avenues. In the early 1900s, the mainline was reconstructed in a cut and cover tunnel section. The LIRR’s Atlantic Yard was constructed circa 1908 to service the terminal. It was depressed about 25 feet below street grade to coincide with the LIRR’s mainline tunnel under Atlantic Avenue. Record drawings indicate that the gravity retaining walls lining the perimeter of the yard and other ancillary structures had been designed for an allowable bearing pressure of five tons per square foot (tsf). Perhaps by coincidence, the mat foundation for the tower of the Williamsburg Savings Bank was also designed for five tsf in 1929.Figure 1 shows a typical geologic section through the site. The geology and subsurface conditions in this part of Brooklyn consist of fill generally five to 20 feet deep underlain by dense to very dense sand and gravel; in places, with numerous cobbles and boulders which make pile installation challenging. The sand strata that are on the order of 150 to 200 feet thick were laid down by glaciers during the last ice age and have been heavily precompressed. The sand strata are underlain in places by remnants of the Cretaceous-era Raritan Clay formation and Fordham Gneiss bedrock. Because of this, the sand strata generally provide excellent support for shallow foundations and the allowable bearing of five tons per square foot is usually easily justified."

Jan 1, 2016

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By R. W. Van Dolah

A premature detonation of an explosive charge occurred on January 30, 1961, at a face being prepared for blasting in the underground Jefferson Island Salt Mine, Diamond Crystal Salt Co., Jefferson Island, Iberia Parish, La. The accidental blast injured the powderman fatally; his helper was injured also, but recovered. The accident represents the first fatality reported to the Bureau of Mines in connection with the use of ammonium nitrate-fuel oil (AN-FO) blasting agents in underground mining in the United States. Representatives of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activity conducted the investigation, upon request of the manufacturer of the ammonium nitrate being used and with concurrence by the mine management.

Jan 1, 1962

By J. K. Wen

The Mojiang nickel deposit is situated in Mojiang county, yunnan province, a tropical area in the southwestern China. The known geological resource (measured and inferred) includes 4 million tons of nickel sulphide ore at an average grade of 0.50% Ni and 0.34% As. Nickel minerals are mainly gersdorffite (NiAsS), millerite(NiS), morenosite (NiSO4?7H2O), and more than 50% nickel minerals is gersdorffite which contains arsenic. Pyrite is the dominant sulfide mineral, 22% in the ore and part of nickel minerals are locked in pyrite. It is difficult to attain the nickel concentrate quality allowed by a smelter and the acceptable nickel recovery through flotation due to the high arsenic in the ore and the nickel minerals locked in pyrite. The shake flask tests and column tests for nickel recovery from the Mojiang nickel sulfide ore had been finished by the end of 2003. The column bioleaching tests were carried out using the columns with diameter of 120 mm and height of 1200 mm, and 70% of nickel dissolution was attained in 300 days. A 10,000t pilot test heap was built in the Mojiang Nickel Mine by June 2003. The ore used in the test heap was supplied from the underground mine and was crushed to -20 mm before being feeding to the test heap, which is 4~5 m high, 30 m wide and 50 m long. The naturally adapted mesophile and moderate thermophile have been inoculated into the leaching pile by June 2003. The operating temperature in the heap ranges from 38? to 55?, varying with season. 30% of nickel dissolution was achieved in 3 months and the typical pregnant leach so-lution (PLS) contains 2~3 g/L Ni and 20~30 g/L Fe. The Ni sulfide which was produced by us-ing Na2S 10 t/t?Ni contains 16%~20% Ni and Ni recovery was 98%. 70% of Ni dissolution is expected in 12 months. The test heap was scaled up to 60,000 t of ore per year by mid of 2005. In this paper metallurgical studies and performance of the pilot test heap will be described. The results of mineralogy, shake flask tests and column tests on bioleaching of the nickel sulfide ore are reviewed. The key test heap operation parameters, the performance of bio-heap leahing-Na2S precipitation, ferrous oxidation-ferric precipitation-Na2CO3 precipitation, bacteria in the pile, water and acid balance, effluent disposal, capital and operation costs are also discussed.

Jan 1, 2014

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By W. G. Pariseau

This paper is concerned with the problem of calculating ground movement that occurs as a consequence of mining. Solution to this problem is straight forward in principle but rather complex in practice. The complexities of the problem arise from the ever present constraints of technology and economics. However, the identity of these constraints is often obscured by a faulty understanding of the fundamentals of the problem and a lack of appreciation of current computational capabilities and costs. As a consequence much time and effort are sometimes wasted on gathering information that is of little direct value to ground control programs while important input data are neglected. This paper therefore reviews the essentials of the process of formulating the ground movement problem. Emphasis is upon application to longwall mining, although much of the discussion applies to other mining methods as well. In many instances, the hardrock term stope could be substituted for longwall panel because the fundamentals of the problem are independent of the excavation dimensions and numerical values of rock properties. The latter affect the outcome of a calculation, of course, but not the underlying formulation. Only the major features of the problem are discussed in this brief review. The objective of the discussion is the generation of a reliable basis for developing a technically sound ground control strategy. Any rational ground control strategy must be consistent with basic physical laws. For example, under static conditions, equations of equilibrium must be satisfied. Operational, that is, tactical, details may vary widely with local conditions, but the basic approach must be based on physical laws. The alternative empirical route is intrinsically unreliable and unnecessary as well. Empirical descriptions of ground motion caused by mining including recent statistical curve fits to specialized data sets (for example, surface subsidence data) as well as antiquated "theories" of ground pressure and so forth, however dignified with mathematical formulas, are hardly worthy of the label "theory". Extrapolation of statistical data is always accompanied by rapidly diverging confidence limits, while empirical equations simply lack predictive capability under circumstances even slightly different from those of the original development. For example, applications of surface subsidence curves generated empirically in the United Kingdom to coal mines in the United States generally result in considerably greater subsidence and wider subsidence troughs than actually observed. Locally, empirical criteria for specific ground control actions may be made practical through trial and error, but such tactics are no basis for the development of a general ground control strategy. In this regard, it is worthwhile to recall the traditional scientific distinctions between speculation, hypothesis and law, between the empirical and the proven.

Jan 1, 1982

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man's potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth's outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By Paul M. Tyler, R. M. Santmyers

Platinum and its allied metals osmium, iridium, rhodium , palladium, and ruthenium are the most costly of the better-known metals and combine properties that make them unique among the elements . For a number of isolated uses substitutes have been found which are cheaper and quite as satisfactory ; but none will replace platinum in many of its varied uses , and there is a large and growing demand for purposes for which no economical substitutes are known . As this paper is being written the supply of platinum tends further to increase as a result of the exploitation of newly developed resources and the expansion of production from older sources . In obedience to economic law prices have declined steadily . Buyers , always reluctant to commit themselves on a falling market , have maintained a waiting attitude , and consumption trends are not clearly indicated . Should platinum again approach the price of gold , the natural tendency would be to use more of the metal . In recent years , however , the industrial and scientific uses of platinum have become subordinate to its consumption in jewelry . In matters of personal adornment the popular whim and not practical utility is the dominant factor in demand , and it does not follow that lowered prices will stimulate demand . The substitution of white gold and certain plated goods for platinum may be checked by cheaper platinum , but a fickle public that turned from gold to platinum when platinum became the more costly metal can not with certainty be expected to buy more platinum jewelry because more of the metal than formerly may now be had for the same price . The dearth of platinum during and for some years after the World War had a profound effect upon prices , and this in turn wrought important changes in the field of consumption . When prices advanced the chemical industry, formerly the leading consumer of platinum, was forced to economize in its consumption of the metal and to substitute other metals whenever it could . Somewhat similar conditions resulted in the electrical industry and in the use of platinum in dentistry . Some of these former outlets are permanently closed , and others may be reopened now that platinum prices have receded to pre-war levels , but despite the general expansion of industrial and scientific activity since 1913 the demand for platinum outside the jewelry trade has suffered a net decline . Since the metallurgy of platinum is relatively simple the reason for its high price is its relative scarcity in the earth's crust . An interesting speculation set forth by certain geologists attributes the extraordinarily high density of the interior of the earth in part to the presence of iron alloyed with substantial amounts of platinum and other related metals . In support of this hypothesis it may be said that platinum is often found in meteorites , and known deposits in the earth's crust are all of deep - seated origin . However , even if there were a high concentration of platinum in the interior of the earth it would be next to impossible at the present state of our knowledge to make it available , and the world would continue to depend for its supply on deposits found within minable depths below the surface . For many years before 1914 the world obtained its supply of platinum metals primarily from Russia , which before the war produced as much as 300,000 troy ounces in a year , or approximately 95 per cent of the world output . Despite fluctuations due to internal political disturbances Colombia managed to account for 3 to 4 per cent , leaving the rest of the world to furnish the remaining 1 to 2 per cent .

Feb 1, 1931

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete walls. PRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

MR. SHUBART: Mr. Miller's paper mentioned the two processes that seemed to be a success, the Smith process and the Piron process. I suppose the main difference is this, that Smith's process is to furnish domestic fuel and the by-products while the Piron process that Ford is installing is for fuel for power plants. I would like to ask Mr. Miller something about the commercial cost of the process. With the briquette you must make it cheap enough to sell. What are the commercial possibilities of Smith's briquette? MR. MILLER: It is pretty hard to say what the cost would be at this time, owing to the fact that slack has advanced double, or even more at the time I was in New York with the plant, but at that time it was costing $1.10 for the operation. You can add to that, of course, the cost of the coke. One dollar and ten cents was the entire cost of plant operation. It takes about one and one-half tons of coal to make a ton of briquettes. One dollar and ten cents takes care of all the material, cost, labor, handling, etc. Labor was much cheaper then. I would say it would cost about $2.20 now. The cost of coal is what you can buy it for on the market. I don't think, however, that the carbocoal process will ever meet with any great favor for the simple reason that it is really a prepared fancy fuel. It is going to be nice for people in offices where they want a grate or for families where they want a nice clean fuel. It leaves no stain on the fingers, no odor to it. It seems in carbonizing coal we change the carbon molecule. For instance, we are all familiar with the diamond. It is carbon, yet it requires a tremendous heat to burn a common little diamond. But you can set a piece of charcoal afire, which is also carbon, with a match. The molecular form has been changed in carbonizing coal, i. e., it is larger. Carbocoal will fire very readily, it can be started with a piece' of paper. I think the Piron process will be the process, i. e., to simply take out the tars and light oils, then fire direct-have the distillate plants right on the job. CHAIR: Can Mr. Shubart tell us something of the mechanical part of the Piron process? MR. SHUBART: The Piron process is of interest because Mr. Ford is taking it up. He has made so few mechanical mistakes it makes us feel that it is a success. Piron is a chemist of high accomplishment and reputation. The thing about the proces is its simplicity. Mr. Smith's is a very elaborate process, but Piron has gotten around all that. Piron feeds the raw coal in at about one-half inch mesh or smaller. He feeds it into a retort about 55 feet long, 16 feet wide over all. He has a hearth about 6 feet wide and the length of the retort. The base of the hearth that carries the coal is a conveyor, a flat cast iron conveyor, a very massive affair, very accurately made, so that there is no loss of coal. Between the upper and lower strands of the ' conveyor is a bath of molten lead which gives an accurate control of temperature. For best results he must have temperature of not under 800 F., not over 1,300 degrees F., about 1,100 or 1,200 F. seems to be ideal for getting greatest yield of oils and the best tars and other by-products. This lead bath has a system of flues running through it that

Jan 1, 1923